topic This was a UX AP that was not in Wireless

AP 1532 Flashing Green and RED

Jose Lucas — Mon, 05 Jul 2021 12:07:43 GMT

Hello

I have a controller 5508, with, internal antennas 2700 Series and external antenas. All APs work fine, internal APs have green led and when somebody connect turn to Blue.

But with the external antenas i have the led blinking green and red, I check the AP and is perfectly recheable by ping, is registered fine on WLC,and have user connected and ALL works fine!! ...

My question is what means blinking Red and green ???

PD: in the WLC log not show nothing wrong

Thanks

does your 2700 have enough

jiflorwi — Wed, 25 May 2016 19:14:54 GMT

does your 2700 have enough power?

Refer link for led status :

mohanak — Tue, 31 May 2016 01:44:18 GMT

Refer link for led status : http://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/7-6/b_1532_dg/b_1532_dg_chapter_01.html#topic_F403431A3EF44764B7AC38527D0A50B6

- Most probably not enough

Mark Elsen — Thu, 02 Jun 2016 12:16:24 GMT

- Most probably not enough power, check your ap-log (too), either from the ap-console or else from a remote connection.

i was looking and inline

Jose Lucas — Sat, 04 Jun 2016 03:37:34 GMT

i was looking and inline power is close to the limit of use.

Thanks for the Hint !! I Will solve it changin some aps to other switch with more free inline power.

I have changed the AP to

Jose Lucas — Mon, 06 Jun 2016 14:14:50 GMT

I have changed the AP to other switch with POE+ and enough free inline power and the problem persist.

in the AP log not show nothing rare, in the controller log the same, nothing rare.

This is the loading secuence

blinking green
Cycling through RED, GREEN, AMBER, and OFF
After a while blinking red and green.

In the controller i saw the AP registered OK working at fullpower 30 Watts.

Could you give any idea what could be hapenning?

Thanks!!

I have the same issue. The

npnilssonab — Thu, 29 Dec 2016 23:02:44 GMT

I have the same issue. The power is normal. Only this device connected to a switch providing 150W the port can also deliver 34,4W the max usage of the AP1532E is 48V x 0,7A = 33,6W

There is no SSIDs announced,

The current power usage of the port is at around 5W

The device is UX and not enroled in any country but the Controller has only one Country code selected.

led blinking red and green

npnilssonab — Thu, 29 Dec 2016 23:07:03 GMT

led blinking red and green and off

It's not listed....

To UX device:

Alexander Borodavko — Fri, 06 Jan 2017 20:01:02 GMT

To UX device:

You will see the APs LED blinking red and green even though the AP has obtained the IP address and joined the controller. This is because there is no regulatory domain set on the AP, and it has not been primed with the correct domain.

Universal AP Regulatory Domain Deployment Guide http://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/8-0/AP_Regulatory_Domain_DG/b_universal_AP_regulatory_domain_DG.html

This was a UX AP that was not

npnilssonab — Thu, 09 Feb 2017 07:48:38 GMT

This was a UX AP that was not attached to a region. For future referens, this is not clear in the documentation.

http://www.cisco.com/c/en/us/td/docs/wireless/access_point/ux-ap/guide/uxap-mobapp-g.html