topic The problem for us was that in Wireless

Transfer cannot happen because at least one AP is upgrading

fabianwickman — Mon, 05 Jul 2021 08:40:54 GMT

Hi,

We have 10 WLC5508 in our environment, and I am upgrading them to code 7.6.120.0.

I am stuck with one controller, wich is saying "Transfer cannot happen because at least one AP is upgrading", when i type "transfer download start" in cli. All the other controllers, wich were on the same code hasn't presented any problems. All the APs on the controller have different images, some have the new(7.6.120.0) and some the old, wich is 7.4.121.0

I have tried rebooting the controller, but nothing changes.

I cannot start to transfer the code...

Issue reset system forced

Saurav Lodh — Wed, 08 Oct 2014 01:14:53 GMT

Issue reset system forced from CLI

Have tried that. Still the

fabianwickman — Wed, 08 Oct 2014 12:09:24 GMT

Have tried that. Still the same result when trying to transfer new code to controller. Thanks for tip!

When we ran into this, we

Darren — Wed, 08 Oct 2014 16:53:26 GMT

When we ran into this, we would reboot the AP that is stuck downloading. Then while that AP is rebooting, you can start your code transfer.

Interesting. Thanks Darren.

fabianwickman — Wed, 08 Oct 2014 19:38:45 GMT

Interesting. Thanks Darren. Well, the problem is that there are 0 APs downloading, so we can't find wich AP that is stuck. One solution would be to move the APs to another controller, only it's pretty much work, about 450 aps on that controller. Or to reset them all, and meanwhile start code transfer, seems risky though. The 7.6.120.0 code doesn't seem stable.

We were succcessful to

fabianwickman — Thu, 09 Oct 2014 07:39:42 GMT

We were succcessful to transfer the code when:

Resetting all the APs on the controller, and then found one that didn't reset(in cli). We shut the port on the one that didn't reset, and then issued reset on all APs again, and then started the code transfer. That worked. Thanks for all input.

i have the sami issue with a

Marco Matera — Thu, 23 Apr 2015 09:29:03 GMT

i have the same issue with a cisco 8510 controller with Version 7.4.121.0 (2500 AP's are registered).

I have tried to download a new WebAuthCert for a Hotspot SSID but the following failure occurs

--> Transfer cannot happen because at least one AP is upgrading , but thtere is no ap in downloading or upgrading modus???

The problem for us was that

fabianwickman — Thu, 23 Apr 2015 09:57:30 GMT

The problem for us was that one or a couple of APs were stuck in some form of download. The only way to to find those APs was to reset all APs and then look in the cli for those APs that didn't reset. Shut the switchport of those APs. Not very neat, but it worked.

thx for your fast reply

Marco Matera — Thu, 23 Apr 2015 14:22:34 GMT

thx for your fast reply fabian. But i think there is no way to reset all 2500 AP's. I Hope to find another solution

Had issue were some APs were

ROB ADAMS — Thu, 07 May 2015 18:57:04 GMT

Had issue were some APs were in downloading status on 7.4. Shut AP ports. Set WLC back to 7.2. Enabled ports to get the handhelds working on 7.2. Then downloaded 7.4 again. Rebooted and resolved APs downloading issue.

hi rob,thx for the answer but

Marco Matera — Fri, 08 May 2015 06:57:43 GMT

hi rob,

thx for the answer but for a productive enviroment it is not so easy to downgrade or upgrade over 2500 Access Points. We solved the Problem that we rebooted the controller over the Prime Infrastructure and then it was able to start the transfer.