topic i can,t get full data transfer rate on cisco 3602 AP in Wireless

i can,t get full data transfer rate on cisco 3602 AP

RASHID ASGHAR — Mon, 05 Jul 2021 07:08:54 GMT

version 15.2

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

hostname Php

logging rate-limit console 9

enable secret 5 $1$icM5$N/nc3E1UFeA6He0/WUtO/1

no aaa new-model

no ip routing

no ip cef

dot11 syslog

dot11 ssid Php

authentication open

guest-mode

dot11 band-select parameters

cycle-count 3

cycle-threshold 200

expire-supression 20

expire-dual-band 60

client-rssi 80

dot11 network-map

dot11 adjacent-ap age-timeout 1000

dot11 guest

username Cisco password 7 106D000A0618

username admin privilege 15 secret 5 $1$N9mw$Bzw6WJypMzG0hCc9XaRQV/

bridge irb

interface Dot11Radio0

bandwidth 10000000

no ip address

no ip route-cache

encryption key 1 size 40bit 7 8A0DE8A0C95E transmit-key

encryption mode wep optional

ssid Php

antenna gain 0

stbc

speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0

station-role root

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

interface Dot11Radio1

bandwidth 10000000

no ip address

no ip route-cache

encryption key 1 size 40bit 7 D20EB4C0DC26 transmit-key

encryption mode wep optional

ssid Php

antenna gain 128

peakdetect

no dfs band block

stbc

speed basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0

channel dfs

station-role root

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

interface GigabitEthernet0

no ip address

no ip route-cache

duplex auto

speed auto

bridge-group 1

bridge-group 1 spanning-disabled

no bridge-group 1 source-learning

interface BVI1

ip address 192.168.1.11 255.255.255.0

rate-limit input 2000000000 512000000 1024000000 conform-action transmit exceed

-action transmit

rate-limit output 2000000000 512000000 512000000 conform-action transmit exceed

-action transmit

no ip route-cache

ip default-gateway 192.168.1.1

ip forward-protocol nd

ip http server

no ip http secure-server

ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag

bridge 1 route ip

line con 0

line vty 0 4

transport input all

end

Re: i can,t get full data transfer rate on cisco 3602 AP

Scott Fella — Tue, 11 Feb 2014 13:05:45 GMT

First off, to achieve better rates you need to look at 802.11n standards.

You need to use open or WPA2/AES, WEP and WPA/TKIP is not supported. WMM needs to be enabled on the WLAN and under the 5ghz radio, you need to have channel width set to 80. You also need to have a 802.11n client or an 802.11ac client to see the higher speeds. How your ap
Is configured, you will see the basic rates.

Sent from Cisco Technical Support iPhone App

Re: i can,t get full data transfer rate on cisco 3602 AP

Rasika Nayanajith — Tue, 11 Feb 2014 17:54:40 GMT

Just to add, since your 3600 does not have ac module on it, max channel width you can set is 40MHz on Radio 1 interface.

Here is suggested configuration to get it working. I have used WPA2/AES with PSK

dot11 ssid Php

authentication open

guest-mode

authentication key-management wpa version 2

wpa-psk ascii

interface Dot11Radio0

encryption key 1 size 40bit 7 8A0DE8A0C95E transmit-key

encryption mode wep optional

encryption mode ciphers aes-ccm

ssid Php

speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0

speed default

station-role root

bridge-group 1

interface Dot11Radio1

encryption key 1 size 40bit 7 D20EB4C0DC26 transmit-key

encryption mode wep optional

encryption mode ciphers aes-ccm

ssid Php

channel width 40-above

speed basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0

speed default

station-role root

bridge-group 1

As long as you have a device with 3SS support on 5GHz you should get highest data rates ( theoratical max 450Mbps, practically around 200Mbps). If it is 2SS then you will get max 300Mbps (theoratical). Below should help you to get an idea about those MCS data rates

HTH

Rasika

**** Pls rate all useful responses ****

i can,t get full data transfer rate on cisco 3602 AP

Scott Fella — Tue, 11 Feb 2014 18:02:34 GMT

Good catch... I was thinking it was a 3702:)

Thanks,

Scott

*****Help out other by using the rating system and marking answered questions as "Answered"*****