topic Service ports are only in Wireless

interfaces on WLC

codflanglers — Mon, 05 Jul 2021 12:20:33 GMT

I have a couple of things to clarify on 5508 WLCs set up in HA:

Service ports are only accessible via SSH and not HTTPS correct?

Should I be able to access the redundancy-management interface on the standby controller? I assume via SSH again and not via HTTPS. The reason I ask is I can access the redundancy-management interface via SSH on the active controller but not the standby.

Service ports are only

Leo Laohoo — Thu, 30 Jun 2016 22:14:25 GMT

Service ports are only accessible via SSH and not HTTPS correct?

Service ports can be accessed using Telnet and/or SSH, HTTP and/or HTTPs.

Should I be able to access the redundancy-management interface on the standby controller?

Yes.

The primary is the only one

mohanak — Fri, 01 Jul 2016 02:00:01 GMT

The primary is the only one that can be reachable using http/https/telnet/ssh with AP SSO enabled. Once SSO is enabled, the Standby WLC can be accessed via console connection or via SSH on the service port and on the redundant management interface.

http://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/7-5/High_Availability_DG.html

OK well I have the issue that

codflanglers — Wed, 24 Aug 2016 08:55:57 GMT

OK well I have the issue that I can ssh via the service-port OK and I can ping the redundancy-management interface but I can't ssh or https to it?

Is there something I need to set/check on the WLC that I could've missed?

Also, I am under the impression that there is no way to monitor the secondary WLC once you enable HA...is that correct?

Using CLI, post the complete

Leo Laohoo — Wed, 24 Aug 2016 10:07:56 GMT

Using CLI, post the complete output to the command "sh network summary".

(Cisco Controller-Standby)

codflanglers — Wed, 24 Aug 2016 10:15:12 GMT

(Cisco Controller-Standby) >show network summ

RF-Network Name............................. XXXXXXXX
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Disable
Secure Web Mode RC4 Cipher Preference....... Disable
Secure Web Mode SSL Protocol................ Disable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
IPv4 AP Multicast/Broadcast Mode............ Unicast
IPv6 AP Multicast/Broadcast Mode............ Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
MLD snooping................................ Disabled
MLD timeout................................. 60 seconds
MLD query interval.......................... 20 seconds

--More-- or (q)uit
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Disable
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth CMCC Support ...................... Disabled
Web Auth Redirect Ports .................... 80
Web Auth Proxy Redirect ................... Disable
Web Auth Captive-Bypass .................. Disable
Web Auth Secure Web ....................... Enable
Web Auth Secure Redirection ............... Disable
Fast SSID Change ........................... Disabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
Link Local Bridging Status ................. Disabled
CCX-lite status ............................ Disable
oeap-600 dual-rlan-ports ................... Disable
oeap-600 local-network ..................... Enable

--More-- or (q)uit
oeap-600 Split Tunneling (Printers)......... Disable
WebPortal Online Client .................... 0
WebPortal NTF_LOGOUT Client ................ 0
mDNS snooping............................... Disabled
mDNS Query Interval......................... 15 minutes
Web Color Theme............................. Default
Capwap Prefer Mode.......................... IPv4
Client ip conflict detection (DHCP) ........ Disabled

Web Mode.....................

Leo Laohoo — Wed, 24 Aug 2016 10:46:09 GMT

Web Mode.................................... Disable

HTTP is disabled

Secure Web Mode............................. Enable

HTTPS is enabled.

Secure Shell (ssh).......................... Enable
Telnet...................................... Disable

I think this is self-explanatory.

Absolutely. But the issue I

codflanglers — Wed, 24 Aug 2016 11:01:19 GMT

Absolutely. But the issue I am seeing is that whilst I can SSH to the service-port I cannot SSH to the redundancy-management interface.

According to the documentation I should be able to. It pings OK, but SSH just times out.

Post the complete output to

Leo Laohoo — Wed, 24 Aug 2016 23:08:07 GMT

Post the complete output to the command "sh sysinfo" and "sh red summary".