tópico Hi na Wireless

Cisco Aironet 1600 function only in 54mb, how to configure for function in 150mb or 300mb?

anderson_araujo1 — Mon, 05 Jul 2021 12:17:52 GMT

Cisco Aironet 1600 function only in 54mb, how to configure for function in 150mb or 300mb?

Makesure below are full

Rasika Nayanajith — Fri, 24 Jun 2016 21:02:18 GMT

Makesure below are full filled

1. SSID security should have either WPA2/AES or Open authentication (no security)

2. WMM is enabled

HTH

Rasika

*** Pls rate all useful responses ***

Hi,

anderson_araujo1 — Mon, 27 Jun 2016 17:40:26 GMT

Hi,

Rasika

Wep key 40bits OK

In services, QOS, WiFi MultiMedia (WMM)
Enable on Radio Interfaces:
Radio0-802.11N2.4GHz OK
Radio1-802.11N5GHz OK
And is working only 54mb, I could not run the 150 and 300mb

Thanks a Lot

Wep key 40bits OK

Rasika Nayanajith — Mon, 27 Jun 2016 19:47:01 GMT

Wep key 40bits OK

WEP won't support it. You have to change security settings to WPA2/AES if you want to achieve any data rates beyond 54Mbps

HTH

Rasika

*** Pls rate all useful responses ***

I dont have the WPA2 / AES

anderson_araujo1 — Mon, 27 Jun 2016 20:08:51 GMT

I dont have the WPA2 / AES option only options:
Four options:
No security,
EAP Authentication
Wpa
wep Key

How do I enable the option?

Thanks a lot.

What is software version you

Rasika Nayanajith — Mon, 27 Jun 2016 21:08:07 GMT

What is software version you got ? "show version" from your AP CLI should provide this info.

If you look CLI config something like below is what you need

dot11 ssid <SSID_NAME>
   authentication open
   authentication key-management wpa version 2
   guest-mode
   wpa-psk ascii <SSID_PASSWORD>

Refer this thread for complete configuration

https://supportforums.cisco.com/discussion/12389761/basic-configurations-air-sap1602i-ak9

HTH

Rasika

*** Pls rate all useful responses ***

Hi,

anderson_araujo1 — Tue, 28 Jun 2016 18:40:22 GMT

Hi,

How to write in mode terminal?

does not accept keyboard typing

In my Terminal i dont write.

I use putty in cable console, usb, serial.

ap>sh run ^% Invalid input

anderson_araujo1 — Tue, 28 Jun 2016 19:30:04 GMT

ap>sh run
^
% Invalid input detected at '^' marker.

ap>sh running-config
^
% Invalid input detected at '^' marker.

ap>conf t
^
% Invalid input detected at '^' marker.

ap>

Hi

anderson_araujo1 — Tue, 28 Jun 2016 19:59:33 GMT

I logged in I

Ap#

I execute

conf t
hostname AP
!
dot11 ssid CDS_FIBRA-CSO
authentication open
authentication key-management wpa version 2
guest-mode
wpa-psk ascii password
!
interface Dot11Radio0
encryption mode ciphers aes-ccm
ssid CDS_FIBRA-CSO
no shutdown
!
interface Dot11Radio1
encryption mode ciphers aes-ccm
ssid CDS_FIBRA-CSO
no shutdown
!
interface BVI1
ip address dhcp
!
end
write memory
!

after the command, did not take the settings, he continued the way it was

go into enable mode first

Rasika Nayanajith — Tue, 28 Jun 2016 20:09:01 GMT

go into enable mode first (use password Cisco if it is default settings). Then go into config mode & do you configs

ap>enable

ap#conf t

HTH

Rasika

Is it Autonomous access

mohanak — Wed, 29 Jun 2016 01:49:56 GMT

Is it Autonomous access points?, try configuring MCS : http://www.cisco.com/c/en/us/td/docs/wireless/access_point/15-3-3/configuration/guide/cg15-3-3/cg15-3-3-chap6-radio.html#63753

Hi

anderson_araujo1 — Wed, 29 Jun 2016 16:56:17 GMT

My version is C1600 Software (AP1G2-K9W7-M), Version 15.2(2)JB2, RELEASE SOFTWARE (fc1)

OM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)

I dont understand

I use this comand:

Guest_Ap#sh run
Guest_Ap#sh running-config
Building configuration...

Current configuration : 1768 bytes
!
version 15.2
no service pad
service timestamps debug dateti
service timestamps log datetime msec
service password-encryption
!
hostname Guest_Ap
!
!
logging rate-limit console 9
enable secret 5 $1$pFm8$lTS6.1RyyiI7OthLLJf790
!
no aaa new-model
no ip routing
no ip cef
!
!
!
dot11 syslog
!
dot11 ssid Guest_AP7
   authentication open
   authentication key-management wpa version 2
   guest-mode
   wpa-psk ascii 7 045C07090D20405E060E0005
!
!
crypto pki token default removal timeout 0
!
!
username Cisco password 7 1531021F0725
!
!
bridge irb
!
!
!
interface Dot11Radio0
no ip addr
no ip route-cache
!
encryption mode ciphers aes-ccm
!
ssid Guest_AP7
!
antenna gain 0
stbc
beamform ofdm
channel 2432
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
antenna gain 0
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loo
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
!
interface BVI1
ip address 172.21.10.x 255.255.255.0
no ip route-cache
!
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodcon                                                                ;

!
bridge 1 route ip
!
!
!
line con 0
line vty 0 4
login local
transport input all
!
end

Or this command ?

conf t
hostname <AP_HOSTNAME>
!
dot11 ssid <SSID_NAME>
   authentication open
   authentication key-management wpa version 2
   guest-mode
   wpa-psk ascii <SSID_PASSWORD>
!
interface Dot11Radio0
 encryption mode ciphers aes-ccm
 ssid <SSID_NAME>
 no shutdown
!
interface Dot11Radio1
 encryption mode ciphers aes-ccm
 ssid <SSID_NAME>
 no shutdown
!
interface BVI1
 ip address dhcp
!
end
write memory
!

AP(config)#hostname APAP

anderson_araujo1 — Wed, 29 Jun 2016 18:07:16 GMT

AP(config)#hostname AP
AP(config)#!
AP(config)#dot11 ssid CDS_FIBRA-CSO
AP(config-ssid)# authentication open
AP(config-ssid)# authentication key-management wpa version 2
Dot11Radio0 Error: Encryption mode cipher is not configured
AP(config-ssid)# guest-mode
AP(config-ssid)# wpa-psk ascii password@sps
Error: Key-management WPA is requried for WPA-PSK

AP(config-ssid)#!
AP(config-ssid)#end
AP#write memory
Building configuration...

AP(config)#hostname APAP

anderson_araujo1 — Wed, 29 Jun 2016 19:16:20 GMT

AP(config)#hostname AP
AP(config)#!
AP(config)#dot11 ssid CDS_FIBRA-CSO
AP(config-ssid)# authentication open
AP(config-ssid)# authentication key-management wpa version 2
Dot11Radio0 Error: Encryption mode cipher is not configured
AP(config-ssid)# guest-mode
AP(config-ssid)# wpa-psk ascii password@sps
Error: Key-management WPA is requried for WPA-PSK

AP(config-ssid)#!
AP(config-ssid)#end
AP#write memory
Building configuration...

Hi

anderson_araujo1 — Mon, 11 Jul 2016 18:21:24 GMT

Rasika Naya

How to leaving the strongest signal?

The signal was very weak
How to expand the signal?

Thank a Lot

Post "show dot11 association

Rasika Nayanajith — Mon, 11 Jul 2016 22:46:31 GMT

Post "show dot11 association <mac_address>" output for a wireless client that you see weak signal.

By increasing AP radio power, you can increase the coverage, but again end of the day client capability determine the effective cell size. If AP operate in high power, then client can hear AP, but AP cannot hear client back.

HTH

Rasika

*** Pls rate all useful responses ***

Hi Rasika,

anderson_araujo1 — Tue, 12 Jul 2016 00:43:00 GMT

Hi Rasika,

Thank you for your attention , I could not find this post.
You can enhance the signal is weak? Do you have any configuration or command via terminal?
I'm waiting , thank you.

From your AP cli, can you see

Rasika Nayanajith — Tue, 12 Jul 2016 00:46:57 GMT

From your AP cli, can you see any output for "show dot11 association" command ?

Sorry about the delay, I had

anderson_araujo1 — Thu, 21 Jul 2016 17:56:25 GMT

Sorry about the delay, I had personal problems

What is "show dot11 association" command ?

I have two access point and both are with the weak signal and I do not
the option to configure the channels 11, 12, 13, 14

It is currently showing an error

Aironet Extensions Enabled
Carrier Set Americas
Configured Radio Channel 2452 MHz Channel 9
Transmitter Power error
Active Radio Channel 2452 MHz Channel 9
Channel Width 20 MHz
world mode Multi-Domain Operation: Disable
Recive Antenna: Diversity
Transmit Antenna: Diversity
Internal Antenna Configuration: Enable
Antenna Gain(dBi): 0

what I need to do to improve the signal strength?

follows an attachment

What is "show dot11

Rasika Nayanajith — Thu, 21 Jul 2016 21:10:30 GMT

What is "show dot11 association" command ?

This is a CLI command you can run once you have telnet/ssh or console into AP.

I have two access point and both are with the weak signal and I do not
the option to configure the channels 11, 12, 13, 14

In 2.4GHz, do not choose anything other than CH1, CH6 & CH 11. So in your channel selection, only select those 3 channels.

It is currently showing an error
Aironet Extensions Enabled
Carrier Set Americas
Configured Radio Channel 2452 MHz Channel 9
Transmitter Power error
Active Radio Channel 2452 MHz Channel 9

Move away from channel 9 & let it get one of 1,6,11

If you find our responses are useful , do not forget to rate our responses

HTH

Rasika