topic Hi Rasika, With mbssid guest in Wireless

Multiple SSID on air-sap2602

waqas sardar — Mon, 05 Jul 2021 07:04:49 GMT

Dear Team,

I am configuring air-sap2602 and created multiple ssid but its broadcasting only one ssid instead of multiple.Any one can help me?

Thanks

Multiple SSID on air-sap2602

Sandeep Choudhary — Sun, 02 Feb 2014 07:30:12 GMT

can you paste the config here , then only we can find the cause.

Reagrds

Re: Multiple SSID on air-sap2602

Rasika Nayanajith — Sun, 02 Feb 2014 08:25:03 GMT

Hi Waqas,

You may be missing "mbssid guest-mode" command under SSID configuration & "mbssid" command under radio interfaces. Since it is multiple SSID you require this.

Here is a sample configuration of two SSID (WLAN-1 with vlan 7 & WLAN-2 with vlan 😎 & AP management (on vlan 10). Security configuration used WPA2/AES with PSK

hostname AAP1

dot11 ssid WLAN-1

vlan 7

authentication open

authentication key-management wpa version 2

wpa-psk ascii WLAN-1-KEY

mbssid guest-mode

dot11 ssid WLAN-2

vlan 8

authentication open

authentication key-management wpa version 2

wpa-psk ascii WLAN-2-KEY

mbssid guest-mode

interface Dot11Radio0

encryption vlan 7 mode ciphers aes-ccm

encryption vlan 8 mode ciphers aes-ccm

ssid WLAN-1

ssid WLAN-2

mbssid

station-role root

interface Dot11Radio1

encryption vlan 7 mode ciphers aes-ccm

encryption vlan 8 mode ciphers aes-ccm

ssid WLAN-1

ssid WLAN-2

mbssid

station-role root

interface Dot11Radio0.7

encapsulation dot1Q 7

bridge-group 7

interface Dot11Radio0.8

encapsulation dot1Q 8

bridge-group 8

interface Dot11Radio0.10

encapsulation dot1Q 10 native

bridge-group 1

interface Dot11Radio1.7

encapsulation dot1Q 7

bridge-group 7

interface Dot11Radio1.8

encapsulation dot1Q 8

bridge-group 8

interface Dot11Radio1.10

encapsulation dot1Q 10 native

bridge-group 1

interface GigabitEthernet0.7

encapsulation dot1Q 7

bridge-group 7

interface GigabitEthernet0.8

encapsulation dot1Q 8

bridge-group 8

interface GigabitEthernet0.10

encapsulation dot1Q 10 native

bridge-group 1

interface BVI1

ip address 192.168.10.254 255.255.255.0

ip default-gateway 192.168.10.1

Here is AP connected swtichport configuration. SVI configuratoin & DHCP configuration to be there (not shown here)

**** AP Connected Swtichport *****

int g x/x

switchport trunk encapsulation dot1q

switchport mode trunk

switchport trunk native vlan 10

switchport trunk allow vlan 7,8,10

HTH

Rasika

**** Pls rate all useful responses ***

Hi Rasika, With mbssid guest

chamara siyambalapitiya — Thu, 19 Jun 2014 12:22:23 GMT

Hi Rasika,

With mbssid guest-mode command both of wireless SSIDs work in guest mode? Can I use both of SSIDs in my internal network for two parties?

Thank you

Kind regards

Chamara

Hi Chamara,Guest mode

Sandeep Choudhary — Thu, 19 Jun 2014 12:28:22 GMT

Hi Chamara,

Guest mode broadcasts the SSID and only one SSID can be in gueat mode.

To broadcast multiple SSIDs use mbssid guest-mode on each SSID.

Check the example:

http://rscciew.wordpress.com/2014/05/24/multiple-ssid-configurations-on-autonomous-ap/

Regards

Dont forget to rate helpful posts

Thanks for the reply Sandeep.

chamara siyambalapitiya — Thu, 19 Jun 2014 12:32:39 GMT

Thanks for the reply Sandeep. But my question is are those two SSIDs can use as non guest wireless for my office use

thank again bro

Kind regards

Chamara

of course you can use both

Sandeep Choudhary — Thu, 19 Jun 2014 12:37:35 GMT

of course you can use both ssid of office use.

Its depends on your configuration.

Regards