topic Re: SSID not showing in Wireless

SSID not showing

s-menezes — Sat, 03 Jul 2021 23:18:06 GMT

The company I work for has all its APs controlled by a WISM. I recently deployed an AP out to a WAN site and when the AP boots up, I am able to see on the WISM, able to ping from the WISM and vice-versa, able to ping the IP addresses of the SSID from the switch and vice-versa; however, my laptop is not able to see any SSID. The AP is connected to WS-3560-25TS. Where did I go wrong here?? I am confused. This should be no different than any other site, isn't it??

Re: SSID not showing

Scott Fella — Fri, 08 Aug 2008 02:04:33 GMT

Are you broadcasting that ssid? Is the ap in local or h-reap mode? Also, are you using any AP Groups or have AP Groups Configured.

If the AP has joined the WLC, you should be able to see that ap on the gui or on the cli. If the ap is there, then click on the wireless tab then under radio, click on 802.11a/n or 802.11b/g/n and see if the radios are up. Also verify that that ap is enabled and not disabled.

Re: SSID not showing

s-menezes — Fri, 08 Aug 2008 19:47:42 GMT

Fella5:

Thank you for your response.

(1) The WISM has 3 SSID, 2 being broadcast and one its not. Out of the 3 I am only "seeing" the one that its not broadcasting. Its like I see 1 out of 3 SSIDs.

(2) I do not have any AP groups

(3) I can see the AP at the WISM, ping it, move it around to different WISMS in our network etc..

(4) Under the radio,802.11a/n and 802.11b/g/n, the radios are up and enable..

What can cause my laptop only to see 1 out 3 SSID?? Never seen this type of problem...

Re: SSID not showing

phillsolomon — Sun, 10 Aug 2008 22:54:31 GMT

You didn't say which ver you are using, but I had a similar issue with 5.0.148.

When adding a WLAN, I found I needed to reboot the AP for it to start broadcasting it. Do an AP reboot - does it help?

Re: SSID not showing

dennischolmes — Mon, 11 Aug 2008 12:31:17 GMT

Use version 4.1.185 or 5.1.x This solved several issues on WiSMs. 4.1.185 is the most stable.

Re: SSID not showing

s-menezes — Mon, 11 Aug 2008 13:25:50 GMT

Dennis:

All my WISMs are running ver 4.1.85.

Thanks...

Re: SSID not showing

s-menezes — Mon, 11 Aug 2008 13:27:13 GMT

Phill:

All my WISM uses ver 4.1.85. I have rebooted the AP and the switch, but problem still there. I will replace the switch next.

Thanks...

Re: SSID not showing

s-menezes — Tue, 12 Aug 2008 17:53:18 GMT

Scott:

I verify your suggestion and I went a step further by replacing the switch and the AP; however, I still have the same weird problem. Can you program an AP, connected to a controller, to block SSIDs??

Thanks...

Re: SSID not showing

phillsolomon — Wed, 13 Aug 2008 23:05:07 GMT

do you have WLAN Override on ?

Re: SSID not showing

s-menezes — Thu, 14 Aug 2008 13:02:55 GMT

No...the WLAN was not being broadcasting.

Re: SSID not showing

Scott Fella — Thu, 14 Aug 2008 13:07:24 GMT

You can configure the wlc to only have certain ssid's on it. that would be using the wlan override feature.

Delete the ssid from the wlc and create a total new one with no encryption at all and see if you can see it. Sometimes when you mess around with an ssid it gets corrupted and deleting it and recreating it can fix it.

Let me know

Post your show run-config or show running-config on one of your wlc that the ap is one so we can see if it is setup right.

Re: SSID not showing

s-menezes — Thu, 14 Aug 2008 13:07:51 GMT

Scott:

When you first asked if I was broadcasting the WLAN, I checked the wrong controller. When I started to compare configs bt controllers I realized what was missing.

Thanks...

Re: SSID not showing

Scott Fella — Thu, 14 Aug 2008 13:23:36 GMT

Well I guess everything is working okay now.