topic I HAVE 12 AP. but currently I in Wireless

Go join a capwap controller

k.dominique sawadogo — Mon, 05 Jul 2021 09:14:59 GMT

Hello

*Jan 10 13:21:00.311: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 10 13:21:00.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.1.1.                                            149 peer_port: 5246
*Jan 10 13:21:00.415: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip:                                             10.1.1.149 peer_port: 5246
*Jan 10 13:21:00.415: %CAPWAP-5-SENDJOIN: sending Join Request to 10.1.1.149
*Jan 10 13:21:00.415: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Jan 10 13:21:00.415: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message typ                                            e 10 state 5.
*Jan 10 13:21:00.415: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from con                                            troller
*Jan 10 13:21:00.415: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 1                                            0.1.1.149
*Jan 10 13:21:18.655: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(UNK
., 1)MESSAGE_TYPE (5)
*Jan 10 13:21:18.655: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Jan 10 13:21:18.655: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.1.1.149:52                                            46
*Jan 10 13:21:18.759: slave radio 2 dependancy on radio 1: force to DOWN state

*Jan 10 13:21:18.763: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Jan 10 13:21:18.779: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administrat                                            ively down
*Jan 10 13:21:18.779: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administrat                                            ively down
*Jan 10 13:21:18.779: %LINK-5-CHANGED: Interface Dot11Radio2, changed state to administrat                                            ively down
*Jan 10 13:21:18.791: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jan 10 13:21:18.795: slave radio 2 dependancy on radio 1: force to UP state

I have AIR-CAP3602I-A-K9

Cisco IOS Software, C3600 Software (AP3G2-K9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (f c2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 30-Jul-13 22:57 by prod_rel_team

ROM: Bootstrap program is C3600 boot loader
BOOTLDR: C3600 Boot Loader (AP3G2-BOOT-M) LoaderVersion 12.4(23c)JY, RELEASE SOFTWARE (fc1 )

MY WLC is model 2504 version 7.5.102.0

Can you help me to solve my

k.dominique sawadogo — Sat, 10 Jan 2015 13:46:33 GMT

Can you help me to solve my problem. the controller does not reach the AP

Is the ap and the WLC on the

Scott Fella — Sat, 10 Jan 2015 15:46:27 GMT

Is the ap and the WLC on the same vlan? How many AP's have joined the WLC? Can you post the show inventory from the WLC? You should also upgrade to a better vice version like 7.6.130.0 and also upgrade the FUS to 1.9.0.0. The version you are on is deferred.

-Scott

Please post the following

Freerk Terpstra — Sat, 10 Jan 2015 15:47:52 GMT

Please post the following output:
1. WLC: sh sysinfo;
2. WLC: sh time;
3. AP: sh version;
4. AP: sh inventory

AP1>enPassword:APe4c7.22b2

k.dominique sawadogo — Sun, 11 Jan 2015 09:20:07 GMT

AP1>en
Password:
AP1#sh ver
Cisco IOS Software, C3600 Software (AP3G2-K9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 30-Jul-13 22:57 by prod_rel_team

ROM: Bootstrap program is C3600 boot loader
BOOTLDR: C3600 Boot Loader (AP3G2-BOOT-M) LoaderVersion 12.4(23c)JY, RELEASE SOFTWARE (fc1)

APe4c7.22b2.b0a8 uptime is 1 minute
System returned to ROM by power-on
System image file is "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-xx.152-4.JA1"
Last reload reason:

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
--More-- (196.200.80.24)
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco AIR-CAP3602I-A-K9 (PowerPC) processor (revision A0) with 180214K/81920K bytes of memory.
Processor board ID FTX1748R15A
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.5.102.0
1 Gigabit Ethernet interface
3 802.11 Radios

32K bytes of flash-simulated non-volatile configuration memory.
Part Number                          : 73-14521-02
PCA Assembly Number                  : 800-37501-02
PCA Revision Number                  : A0
Top Assembly Part Number             : 800-35852-02
Top Assembly Serial Number           : FTX1748R15A
Top Revision Number                  : C0
Product/Model Number                 : AIR-CAP3602I-A-K9

Configuration register is 0xF

AP1#sh inventory
NAME: "AP3600", DESCR: "Cisco Aironet 3600 Series (IEEE 802.11n) Access Point"
PID: AIR-CAP3602I-A-K9 , VID: V01, SN: FTX1748R15A

NAME: "Dot11Radio2", DESCR: "802.11AC 5GHz Radio"
PID: AIR-RM3000AC-A-K9 , VID: 1 ,

I HAVE 12 AP. but currently I

k.dominique sawadogo — Sun, 11 Jan 2015 09:25:45 GMT

I HAVE 12 AP. but currently I connected for testing.

Switch between WLC and I had a trunk. PA are in VLan 1 in the Switch

(Cisco Controller) >show

k.dominique sawadogo — Sun, 11 Jan 2015 09:34:55 GMT

(Cisco Controller) >show sysinfo

Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.5.102.0
Bootloader Version............................... 1.0.18
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 16.0

Build Type....................................... DATA + WPS

System Name...................................... WIRELESS
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 10.1.1.149
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 3 mins 8 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180

--More-- or (q)uit
Configured Country............................... FR - France
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +26 C
External Temperature............................. +31 C
Fan Status....................................... 4300 rpm

State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Maximum number of APs supported.................. 25

(Cisco Controller) >show time

Time............................................. Sat Jan 11 00:09:15 2015

Timezone delta................................... 0:0
Timezone location................................

NTP Servers
NTP Polling Interval......................... 86400

Index NTP Key Index NTP Server NTP Msg Auth Status
------- ----------------------------------------------------------------------------------

Put the ap and WLC management

Scott Fella — Sun, 11 Jan 2015 15:07:41 GMT

Put the ap and WLC management in the same vlan and try more than one AP.

-Scott

You have an America country

Scott Fella — Sun, 11 Jan 2015 15:18:00 GMT

You have an America country code access point and your WLC country code is set to France. You need to add US to the WLC country code or add US and remove FR if you don't have plans to locate access points in France. It's important to purchase the proper access point for that country.

-Scott

if activate the debug lwapp

k.dominique sawadogo — Mon, 12 Jan 2015 08:58:28 GMT

if activate the debug lwapp client event of the AP I have result:

*Jan 11 09:33:20.347: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Jan 11 09:33:20.347: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Jan 11 09:33:20.347: LWAPP_CLIENT_EVENT: Dropping discovery in LWAPP. This AP model is not supported by LWAPP WLC.
*Jan 11 09:33:20.347: LWAPP_CLIENT_EVENT: Dropping discovery in LWAPP. This AP model is not supported by LWAPP WLC.

Well your log shows that the

Scott Fella — Mon, 12 Jan 2015 13:31:19 GMT

Well your log shows that the WLC code doesn't support the AP model.

*Jan 11 09:33:20.347: LWAPP_CLIENT_EVENT: Dropping discovery in LWAPP. This AP model is not supported by LWAPP WLC.

Like I mentioned earlier, upgrade to v7.6.130.0 and FUS 1.9.0.0 as v7.5 is horrible.

-Scott