topic Hi Vasco, in Wireless

Cisco MSE or CMX

faisalcis1 — Mon, 05 Jul 2021 11:51:09 GMT

Hi Guys,

I need some information from the experts here, i am in a process of installing the Cisco MSE but when i go to the down load i see the new release 10.x.x named CMX. I need to understand that is the new model re-branded with this name of CMX or should I download the release 8.x.x which is named MSE.

Regards,

Faisal

CMX is as you say, MSE re

Ric Beeching — Fri, 01 Apr 2016 00:49:48 GMT

CMX is as you say, MSE re-branded. The Release Notes say no inline upgrade is available however as you are (I think) doing a fresh install you should be fine. You can install either but if you do install MSE note that a migration later on will be more arduous.

http://www.cisco.com/c/en/us/td/docs/wireless/mse/release/notes/cmx_10_2_rn.html#pgfId-1546447

CMX is a suite of

mohanak — Fri, 01 Apr 2016 01:18:20 GMT

CMX is a suite of applications that are hosted on the Mobility Services Engine and use its ability to locate Wi-Fi devices. The applications include:

CMX Analytics to gain insight into end-user behavior while inside a venue
CMX Connect to provide a venue-specific, location-based mobile guest access experience

http://www.cisco.com/c/en/us/solutions/collateral/enterprise-networks/connected-mobile-experiences/guide-c07-734430.html

Are you planing to integrate

Vasco Costa — Fri, 01 Apr 2016 17:02:39 GMT

Are you planing to integrate CMX 10.2 with Prime 3.0?

If so, go for MSE 8.0 because PI 3.0 doesn't interact with CMX 10.2.
Apparently, only PI 3.1 works with CMX

Hi Vasco,

faisalcis1 — Sun, 03 Apr 2016 11:18:51 GMT

Hi Vasco,

Thanks for your reply yes the final picture is to integrate CMX with Prime3.0 which is also a fresh installation. So am I going to loose any functionality if i go for CMX 10.2 rather than MSE8.0. (It's going to be a VM setup).

Regards,

Cisco CMX 10.1.0

mohanak — Mon, 04 Apr 2016 01:22:32 GMT

Cisco CMX 10.1.0

Cisco CMX 10.1.1

Cisco CMX 10.1.2

This release is suitable for deployments where the following features are required:

Detect & Locate
Analytics
Connect

This release is not suitable for deployments where the following features are required:

aWIPS
CMX SDK
FIPS deployment
Stanley (AeroScout) Certification
Cisco Prime Infrastructure integration for location services and Cisco CleanAir

Cisco CMX 10.2.0

Cisco CMX 10.2.1

This release is suitable for deployments where the following features are required:

Detect & Locate
Analytics
Presence Analytics
Connect
Hyperlocation (Release 10.2.1 or later)
FastLocate (Release 10.2.1 or later)

This release is not suitable for deployments where the following features are required:

aWIPS
CMX SDK
FIPS deployment
Cisco CMX 10.2.x supports RTLS tag integration (such as Aeroscout). Check with the third-party vendor on the availability of CMX-supported software.
Cisco Prime Infrastructure integration for location services and Cisco CleanAir

Hi Mohanak

flavio.elawi1 — Fri, 15 Jul 2016 14:40:12 GMT

Hi Mohanak

the release notes of CMX 10.2.2 now reports this:

Cisco Prime Infrastructure integration, specifically the ability to see WiFi clients and other devices and Cisco CleanAir information in Prime.

What does cisco means by this? i am able to integrate prime infra 3.1 to cmx (it imports the maps and APs and thats that) and i can see the clients moving on cmx, probably because it gets info from the WLC.

so what does that bullet point means?