AIR-SAP1602I-E-K9 can't display CLI after reset factory

lqnghia80 — Mon, 05 Jul 2021 12:16:27 GMT

hi guy

i've reset factory AP 1602I and it couldn't dislay CLI.

console screen displays as below:

help me!

thanks all

-----------------------------------------

Boot from flash

IOS Bootloader - Starting system.

FLASH CHIP: Micronix MX25L256_35F

Xmodem file system is available.

flashfs[0]: 182 files, 7 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 31936000

flashfs[0]: Bytes used: 10420736

flashfs[0]: Bytes available: 21515264

flashfs[0]: flashfs fsck took 10 seconds.

Reading cookie from SEEPROM

Base Ethernet MAC address: fc:5b:39:b2:e4:53

************* loopback_mode = 0

button is pressed, wait for button to be released...

button pressed for 17 seconds

process_config_recovery: set IP address and config to default 10.0.0.1

Loading "flash:/ap1g2-k9w7-mx.152-2.JB2/ap1g2-k9w7-mx.152-2.JB2"...#############################

File "flash:/ap1g2-k9w7-mx.152-2.JB2/ap1g2-k9w7-mx.152-2.JB2" uncompressed and installed, entry point: 0x100000

executing...

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

Rights clause at FAR sec. 52.227-19 and subparagraph

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco IOS Software, C1600 Software (AP1G2-K9W7-M), Version 15.2(2)JB2, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Compiled Mon 29-Jul-13 12:16 by prod_rel_team

Initializing flashfs...

FLASH CHIP: Micronix MX25L256_35F

flashfs[3]: 182 files, 7 directories

flashfs[3]: 0 orphaned files, 0 orphaned directories

flashfs[3]: Total bytes: 31808000

flashfs[3]: Bytes used: 10420736

flashfs[3]: Bytes available: 21387264

flashfs[3]: flashfs fsck took 9 seconds.

flashfs[3]: Initialization complete.

flashfs[4]: 0 files, 1 directories

flashfs[4]: 0 orphaned files, 0 orphaned directories

flashfs[4]: Total bytes: 11999232

flashfs[4]: Bytes used: 1024

flashfs[4]: Bytes available: 11998208

flashfs[4]: flashfs fsck took 0 seconds.

flashfs[4]: Initialization complete....done Initializing flashfs.

Warning: the compile-time code checksum does not appear to be present.

Radio0 present 8764B 8000 0 A8000000 A8010000 0

Rate table has 180 entries (48 SGI/72 BF variants)

Radio1 present 8764B 8000 0 88000000 88010000 4

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

Warning: the compile-time code checksum does not appear to be present.

cisco AIR-SAP1602I-E-K9 (PowerPC) processor (revision B0) with 98294K/32768K bytes of memory.

Processor board ID FGL1839X1F4

PowerPC CPU at 533Mhz, revision number 0x2151

Last reset from power-on

1 Gigabit Ethernet interface

2 802.11 Radios

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: FC:5B:39:B2:E4:53

Part Number : 73-14671-04

PCA Assembly Number : 000-00000-00

PCA Revision Number :

PCB Serial Number : FOC1837279F

Top Assembly Part Number : 800-38552-02

Top Assembly Serial Number : FGL1839X1F4

Top Revision Number : A0

Product/Model Number : AIR-SAP1602I-E-K9

Press RETURN to get started!

*Mar 1 00:00:11.883: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed

*Mar 1 00:00:13.663: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0

*Mar 1 00:00:14.779: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1

*Mar 1 00:00:15.707: not a autoconfig enabled device!!!

*Mar 1 00:00:17.027: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up

*Mar 1 00:00:18.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down

*Mar 1 00:01:03.887: Starting Ethernet promiscuous mode

*Mar 1 00:01:03.959: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down

*Mar 1 00:01:03.959: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down

*Mar 1 00:01:03.971: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C1600 Software (AP1G2-K9W7-M), Version 15.2(2)JB2, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Compiled Mon 29-Jul-13 12:16 by prod_rel_team

*Mar 1 00:01:03.971: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start

*Mar 1 00:01:04.955: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up

*Mar 1 00:01:04.959: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down

*Mar 1 00:01:04.959: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down

*Mar 1 00:01:15.927: %LINK-6-UPDOWN: Interface BVI1, changed state to down

*Mar 1 00:01:16.927: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down

Check the configuration of

Leo Laohoo — Wed, 22 Jun 2016 03:00:38 GMT

Check the configuration of the Console port.

hi Leo

lqnghia80 — Wed, 22 Jun 2016 03:28:23 GMT

hi Leo

i setted as below:

baud rate: 9600

data bits: 8

parity: None

stop bits: 1

hi Leo

lqnghia80 — Wed, 22 Jun 2016 03:31:04 GMT

hi Leo

i haven't ping IP default of AP (10.0.0.1/24)

How about Flow Control? It

Leo Laohoo — Wed, 22 Jun 2016 03:41:35 GMT

How about Flow Control? It should be OFF.

hi Leo

lqnghia80 — Wed, 22 Jun 2016 03:52:29 GMT

hi Leo

i haven't ping IP default of AP (10.0.0.1/24), too

my console cable is not unplug

topic hi Leo in Wireless

AIR-SAP1602I-E-K9 can't display CLI after reset factory

Check the configuration of

hi Leo

hi Leo

How about Flow Control? It

hi Leo