topic Re: Connectivity issues in Wireless

Connectivity issues

rlopez — Sun, 04 Jul 2021 01:26:26 GMT

hi,

I have a 1231 AP (AIR-AP1231G-A-K9) with an external antenna (AIR-ANT2506). It used to work just fine with the AIR-ANT4941 2.4GHz antenna but we needed to extend the coverage, when we attached the AIR-ANT2506 antenna there is intermitent connectivity no matter if users are close to or far from to the AP. There is no objects which are blocking the signal nor other RFI. Is the antenna the right one for the AP? Any clue about why this is happening?

thank you in advance for your help

Re: Connectivity issues

Rob Huffman — Fri, 22 Jan 2010 17:01:28 GMT

Hi there,

You probably want to set and connect to the Right Primary and take the setting out of Diversity which would have
been set if you were using 2 x 4941's.

Use the antenna configuration interface command to configure the radio receive or transmit antenna settings. Use the no form of this command to reset the receive antenna to defaults.

[no] antenna {receive | transmit} {diversity | left | right}

Syntax Description

receive

Specifies the antenna that the access uses to receive radio signals

transmit

Specifies the antenna that the access uses to transmit radio signals

diversity

Specifies the antenna with the best signal

left

Specifies the left antenna

right

Specifies the right antenna

Defaults

The default antenna configuration is diversity

This example shows how to specify the right receive antenna option:

AP(config-if)# antenna receive right

Hope this helps!

Rob

Re: Connectivity issues

rlopez — Fri, 22 Jan 2010 17:47:12 GMT

hi rib,

I actually did that, I configured the transmit and receive antenna to be the right one but it didn't work. I also performed a carrier busy test, here are the results

Frequency Carrier Busy %
--------- --------------
   2412          4
   2417          2
   2422          2
   2427          6
   2432          4
   2437          2
   2442          4
   2447          2
   2452         22
   2457         21
   2462         33

Frequency Carrier Busy %
--------- --------------
   2412          9
   2417          0
   2422          9
   2427          0
   2432          0
   2437          8
   2442          3
   2447          1
   2452         29
   2457         18
   2462         33

Frequency Carrier Busy %
--------- --------------
   2412          2
   2417          2
   2422          0
   2427          0
   2432          0
   2437          0
   2442          1
   2447          1
   2452         31
   2457         25
   2462         38

the AP is configuredd in channel 6 which is not that busy.

What else should I check?

Thank you in advance.

Re: Connectivity issues

George Stefanick — Sat, 23 Jan 2010 07:22:18 GMT

Here are a few ideas..

1) Put the old antenna back on for testing purposes and see if your issue goes away

2) Is the new antenna defective?

3) Test coverage are static locations (10 feet, 20 feet, 30 feet) with both the new and old antenna to check performance

4) I see you did a busy test, but did you check the spectrum with a spectrum card ?

Re: Connectivity issues

rlopez — Mon, 25 Jan 2010 16:11:48 GMT

thank you Geroge for your reply,

1) with the old antenna the AP was working just fine, but the coverage is limited with no problems, I mean in 30 ft round there is no problem

2) we don't really know if the antenna es defective but ever since we put the antenna to incrase the coverage in the farther places the connectivity goes up and down

3) with both antennas there is no problem within the first 30 ft beyond that we have signal only with the new antenna but the connectivity is not constant

4) I didn't, don't have the spectrum card

Is there something else I can do?

Regards,