topic WiSM module not coming in OPER-UP status in Wireless

WiSM module not coming in OPER-UP status

MICHAEL BURNS — Sun, 04 Jul 2021 05:32:43 GMT

The problem is WiSM module not coming in OPER-UP status , it’s in Started-Keepalive status.

I did run debug wism events on cat6509 and seeing below logs:

Aug 17 05:16:02.930: WiSM-Evt:dman_cntrl_db_search_by_mac: Found mac 30e4.db38.9981 for slot/port 8/1

Aug 17 05:16:02.930: WiSM-Evt:dman_reg_arp_added: cntrl 8/1 got an ip 1.1.1.3 30e4.db38.9981/30e4.db38.9981

Aug 17 05:16:02.930: WiSM-Evt:dman_reg_arp: received a garp from 1.1.1.3/1.1.1.3

Aug 17 05:16:02.930: WiSM-Evt:dman_cntrl_db_search_by_mac: Found mac 30e4.db38.9981 for slot/port 8/1

Aug 17 05:16:02.930: WiSM-Evt:dman_reg_arp_added: cntrl 8/1 got an ip 1.1.1.3 30e4.db38.9981/30e4.db38.9981

Aug 17 05:16:06.870: WiSM-Evt:dman_proc_keepalive_tmr_handler: keepalive timer expired for 8/1

Aug 17 05:16:06.870: WiSM-Evt:dman_cntrl_db_search: something wrong 15

It’s receiving garp request from controller and assign ip to controller but then keepalive time expired and it’s put the controller in started-keeplaive status.

Not sure what’s happening exactly.

Re: WiSM module not coming in OPER-UP status

Amjad Abdullah — Fri, 17 Aug 2012 14:46:40 GMT

What causes the problem to happen? It seems your wism module was ok before so what happened and caused tios issue

Sent from Cisco Technical Support iPad App

WiSM module not coming in OPER-UP status

Leo Laohoo — Sat, 18 Aug 2012 01:50:38 GMT

Can you please post the command: sh wism 8 controller 1 status

WiSM module not coming in OPER-UP status

MICHAEL BURNS — Tue, 21 Aug 2012 03:10:39 GMT

By the way, this is a new install...

JP2-RDC-COR-01#sho wism module 8 controller 1 status

WiSM Controller 1 in Slot 8 configured with auto-lag

Operational Status of the Controller : Started KeepAlive
Service VLAN                         : 93
Service Port                         : 3
Service Port Mac Address             : 30e4.db38.9981
Service IP Address                   : 1.1.1.3
Management IP Address                : 0.0.0.0
Software Version                     :
Port Channel Number                  : 415
Allowed-vlan list                    : 90,800,810
Native VLAN ID                       : 90
WCP Keep Alive Missed                : 0

WiSM module not coming in OPER-UP status

Leo Laohoo — Tue, 21 Aug 2012 03:36:21 GMT

Ok, so what is the output to the command "sh etherchann 415 summary"?

Wait a sec ... No Software Version???

Did you try to console into the WiSM line card?

On the 6500, can you post the output to the command "sh module"?