отмена
Отображаются результаты для 
Вместо этого искать 
Вы имели в виду: 
cancel
Объявления
Community Live

130
Просмотры
0
Полезный материал
0
Ответы
ITal229332657
Beginner

Ошибки после обновления Cisco ASA

Добрый день!

имеется такой девайс Platform Name: ASA 5512-X with SW, 6 GE Data, 1 GE Mgmt, AC

Старючий... Но вообще не пользванный. Решил обновить. На сайте заявлена поддержка новых прошивок от этого года Software Download - Cisco Systems

Залил на девайс. Девайс на этапе загрузки начал падать. Ниже данные по девайсу и данным загрузки и ошибок.

 

Спойлер

rommon #6> show info

Cisco Systems ROMMON Version (2.1(9)8) #1: Wed Oct 26 17:14:40 PDT 2011
Platform Identification and Boot Information:
Controller Type: 0x0709
Platform Name: ASA 5512-X with SW, 6 GE Data, 1 GE Mgmt, AC
Configuration Register: 0x00000001

Interface Device Information:
Management0/0: i82574L, PCI: bus-12, slot-0, fct-0, rev-0, irq-11
GigabitEthernet0/0: i82574L, PCI: bus-5, slot-0, fct-0, rev-0, irq-10
GigabitEthernet0/1: i82574L, PCI: bus-9, slot-0, fct-0, rev-0, irq-10
GigabitEthernet0/2: i82574L, PCI: bus-4, slot-0, fct-0, rev-0, irq-5
GigabitEthernet0/3: i82574L, PCI: bus-8, slot-0, fct-0, rev-0, irq-5
GigabitEthernet0/4: i82574L, PCI: bus-3, slot-0, fct-0, rev-0, irq-10
GigabitEthernet0/5: i82574L, PCI: bus-7, slot-0, fct-0, rev-0, irq-10

 

=============================================================

ciscoasa# reload
Proceed with reload? [confirm]
ciscoasa#


***
*** --- START GRACEFUL SHUTDOWN ---
Shutting down isakmp
Shutting down sw-module
Shutting down License Controller
Shutting down File system

 

***
*** --- SHUTDOWN NOW ---
Process shutdown finished
Rebooting... (status 0x9)
..
INDeconfiguring network interfaces... done.
Sending all processes the TERM signal...
Sending all processes the KILL signal...
Deactivating swap...
Unmounting local filesystems...
Rebooting... Cisco BIOS Version:9B2C111A
Build Date:10/06/2016 07:47:37

CPU Type: Intel(R) Pentium(R) CPU G6950 @ 2.80GHz, 2793 MHz
Total Memory:2048 MB(DDR3 1066)
System memory:619 KB, Extended Memory:2037 MB


PCI Device Table:
Bus Dev Func VendID DevID Class IRQ
---------------------------------------------------------
00 00 00 8086 0040 Bridge Device
00 06 00 8086 0043 PCI Bridge,IRQ=11
00 16 00 8086 3B64 I/O Port Device,IRQ=11
00 1A 00 8086 3B3C USB Controller,IRQ=11
00 1C 00 8086 3B42 PCI Bridge,IRQ=10
00 1C 04 8086 3B4A PCI Bridge,IRQ=10
00 1C 05 8086 3B4C PCI Bridge,IRQ=11
00 1D 00 8086 3B34 USB Controller,IRQ=7
00 1E 00 8086 244E PCI Bridge
00 1F 00 8086 3B16 Bridge Device
00 1F 02 8086 3B22 SATA DPA,IRQ=5
00 1F 03 8086 3B30 SMBus,IRQ=11
01 00 00 10B5 8618 PCI Bridge,IRQ=11
02 01 00 10B5 8618 PCI Bridge,IRQ=10
02 03 00 10B5 8618 PCI Bridge,IRQ=5
02 05 00 10B5 8618 PCI Bridge,IRQ=10
02 07 00 10B5 8618 PCI Bridge,IRQ=5
02 09 00 10B5 8618 PCI Bridge,IRQ=10
02 0B 00 10B5 8618 PCI Bridge,IRQ=5
02 0D 00 10B5 8618 PCI Bridge,IRQ=10
02 0F 00 10B5 8618 PCI Br 8086 10D3 Ethernet,IRQ=10
04 00 00 8086 10D3 Ethernet,IRQ=5
05 00 00 8086 10D3 Ethernet,IRQ=10
07 00 00 8086 10D3 Ethernet,IRQ=10
08 00 00 8086 10D3 Ethernet,IRQ=5
09 00 00 8086 10D3 Ethernet,IRQ=10
0B 00 00 177D 0010 Cavium Encryption,IRQ=11
0C 00 00 8086 10D3 Ethernet,IRQ=11
0D 00 00 1A03 1150 PCI Bridge,IRQ=10
0E 00 00 1A03 2000 VGA,IRQ=10
FF 00 00 8086 2C61 Bridge Device
FF 00 01 8086 2D01 Bridge Device
FF 02 00 8086 2D10 Bridge Device
FF 02 01 8086 2D11 Bridge Device
FF 02 02 8086 2D12 Bridge Device
FF 02 03 8086 2D13 Bridge Device


Booting from ROMMON

Cisco Systems ROMMON Version (2.1(9)8) #1: Wed Oct 26 17:14:40 PDT 2011

 

Use BREAK or ESC to interrupt boot.
Use SPACE to begin boot immediately.

Launching BootLoader...
Boot configuration file contains 3 entries.


Loading disk0:/asa9-12-4-26-smp-k8.bin... Booting...
Platform ASA5512

Loading...
IO memory blocks requested from bigphys 32bit: 41217
INIT: version 2.88 booting
Starting udev
Configuring network interfaces... done.
Populating dev cache
fsck.fat 3.0.28 (2015-05-16)
Starting check/repair pass.
Starting verification pass.
/dev/sdb1: 66 files, 993394/1005550 clusters
dosfsck(/dev/sdb1) returned 0
Mounting /dev/sdb1
IPMI over LAN not active
Running postinst

Loading...
Application cryptographic hash verified
memif is not enabled.
IO Memory Nodes: 1
IO Memory Per Node: 169869312 bytes num_pages = 41472 page_size = 4096

Global Reserve Memory Per Node: 314572800 bytes Nodes=1

LCMB: got 169869312 bytes on numa-id=0, phys=0x17000000, virt=0x7ff2cc400000
LCMB: HEAP-CACHE POOL got 312475648 bytes on numa-id=0, virt=0x7ff2b9800000

total_reserved_mem = 169869312

total_heapcache_mem = 312475648
total mem 874295314 system 2094321664 kernel 3927992 image 97072720
new 871216200 old 874295314 reserve 482344960 priv new 392799232 priv old 607461376
WARNING: Memory allocation adjusted to above minimum threshold. (874295314 / 1073741824)
Processor memory: 1073741824
M_MMAP_THRESHOLD 65536, M_MMAP_MAX 16384
POST started...
POST finished, result is 0 (hint: 1 means it failed)

Compiled on Thu 10-Jun-21 22:22 GMT by builders

WARNING: The FirePOWER module is no longer supported on this model; related ASA configuration was removed.

Total NICs found: 12
i82574L rev00 Gigabit Ethernet @ irq10 dev 0 index 06 MAC: a03d.6f2c.e6ad
i82574L rev00 Gigabit Ethernet @ irq10 dev 0 index 05 MAC: a03d.6f2c.e6b0
i82574L rev00 Gigabit Ethernet @ irq05 dev 0 index 04 MAC: a03d.6f2c.e6ac
i82574L rev00 Gigabit Ethernet @ irq05 dev 0 index 03 MAC: a03d.6f2c.e6af
i82574L rev00 Gigabit Ethernet @ irq10 dev 0 index 02 MAC: a03d.6f2c.e6ab
i82574L rev00 Gigabit Ethernet @ irq10 dev 0 index 01 MAC: a03d.6f2c.e6ae
i82574L rev00 Gigabit Ethernet @ irq11 dev 0 index 00 MAC: a03d.6f2c.e6aa
ivshmem rev03 Backplane Data Interface @ index 07 MAC: 0000.0001.0002
en_vtun rev00 Backplane Control Interface @ index 08 MAC: 0000.0001.0001
en_vtun rev00 Backplane Int-Mgmt Interface @ index 09 MAC: 0000.0001.0003
en_vtun rev00 Backplane Ext-Mgmt Interface @ index 10 MAC: 0000.0000.0000
en_vtun rev00 Backplane Tap Interface @ index 11 MAC: 0000.0100.0001
mmap64: Cannot allocate memory
mmap64: Cannot allocate memory
lina: lina_io.c:561: lina_io_init: Assertion `lina_io_th != 0' failed.
(set_exptime) Timer not a leaf 0x000056066fa3b370. Traceback: 0x000056066b8a6cbe 0x000056066b89e62d 0x000056066b8ae7da 0x000056066b8a8bbc 0x000056066d28bd6b 0x000056066d28d563 0x00007ff2dc661c90 0x0030203d21206874
mgd_timer_set_exptime: Not a leaf called from 0x000056066b8ae7da
core0 same core snap_count=1 signo=11 RIP=56066b8ae81b


-----------------------------------------------
Traceback output aborted.
Flushing first exception frame:
r8 0x00007ff2b98001b0
r9 0x00007ff2b98001b0
r10 0x0000000000000008
r11 0x0000000000003206
r12 0x0000000000000231
r13 0x000056066ebfd3b0
r14 0x000056066f95a538
r15 0x00007fff48472a00
rdi 0x000000000000051d
rsi 0x000000000000051d
rbp 0x000056066ec04805
rbx 0xffffffffffffffff
rdx 0x0000000000000006
rax 0x0000000000000000
rcx 0x00007ff2d7ed34f8
rsp 0x00007fff484722b8
rip 0x00007ff2d7ed34f8
eflags 0x0000000000003206
csgsfs 0x0000000000000033
error code n/a
vector 0x0000000000000000
old mask 0xfffffffe3e3af207
cr2 0x0000000000000000
Nested traceback attempted via signal, from:
Page fault: Address not mapped
r8 0x0000000000000663
r9 0x0000000000000042
r10 0x0000000000000042
r11 0x0000000000003293
r12 0x00005606732244c0
r13 0xffffffffffffdf38
r14 0x00005606732244c0
r15 0x0000000000000000
rdi 0x0000000000000000
rsi 0x00005606735cb3e0
rbp 0x00007fff48471b10
rbx 0x000056066fa3b160
rdx 0x0000000000000000
rax 0x0000000000000000
rcx 0x0000000000000000
rsp 0x00007fff48471b00
rip 0x000056066b8ae81b
eflags 0x0000000000013246
csgsfs 0x0000000000000033
error code 0x0000000000000006
vector 0x000000000000000e
old mask 0xfffffffe3e3af207
cr2 0x0000000000000008

Cisco Adaptive Security Appliance Software Version 9.12(4)26

Compiled on Thu 10-Jun-21 22:22 GMT by builders
Hardware: ASA5512
Target: SMP
Crashinfo collected on 06:30:40.000 UTC Wed Jul 28 2021
ASLR enabled, text region 56066ac83000-56066f631115

Traceback:
0: 0x000056066b85c686
1: 0x000056066b8a794c
2: 0x000056066d28ba4c
3: 0x000056066d28d563
4: 0x00007ff2dc661c90
5: 0x000056066b8a8bbc
6: 0x000056066d28bd6b
7: 0x000056066d28d563
8: 0x00007ff2dc661c90
9: 0x0030203d21206874
-----------------------------------------------
Process shutdown finished
Rebooting... (status 0x8b)
..
iStopping Advanced Configuration and Power Interface daemon: no /usr/sbin/acpid found; none killed
acpid.
Deconfiguring network interfaces... done.
Sending all processes the TERM signal...
Sending all processes the KILL signal...
Deactivating swap...
Unmounting local filesystems...
Rebooting... Cisco BIOS Version:9B2C111A
Build Date:10/06/2016 07:47:37

CPU Type: Intel(R) Pentium(R) CPU G6950 @ 2.80GHz, 2793 MHz
Total Memory:2048 MB(DDR3 1066)
System memory:619 KB, Extended Memory:2037 MB


PCI Device Table:
Bus Dev Func VendID DevID Class IRQ
---------------------------------------------------------
00 00 00 8086 0040 Bridge Device
00 06 00 8086 0043 PCI Bridge,IRQ=11
00 16 00 8086 3B64 I/O Port Device,IRQ=11
00 1A 00 8086 3B3C USB Controller,IRQ=11
00 1C 00 8086 3B42 PCI Bridge,IRQ=10
00 1C 04 8086 3B4A PCI Bridge,IRQ=10
00 1C 05 8086 3B4C PCI Bridge,IRQ=11
00 1D 00 8086 3B34 USB Controller,IRQ=7
00 1E 00 8086 244E PCI Bridge
00 1F 00 8086 3B16 Bridge Device
00 1F 02 8086 3B22 SATA DPA,IRQ=5
00 1F 03 8086 3B30 SMBus,IRQ=11
01 00 00 10B5 8618 PCI Bridge,IRQ=11
02 01 00 10B5 8618 PCI Bridge,IRQ=10
02 03 00 10B5 8618 PCI Bridge,IRQ=5
02 05 00 10B5 8618 PCI Bridge,IRQ=10
02 07 00 10B5 8618 PCI Bridge,IRQ=5
02 09 00 10B5 8618 PCI Bridge,IRQ=10
02 0B 00 10B5 8618 PCI Bridge,IRQ=5
02 0D 00 10B5 8618 PCI Bridge,IRQ=10
02 0F 00 10B5 8618 PCI Bridge,IRQ=5
03 00 00 8086 10D3 Ethernet,IRQ=10
04 00 00 8086 10D3 Ethernet,IRQ=5
05 00 00 8086 10D3 Ethernet,IRQ=10
07 00 00 8086 10D3 Ethernet,IRQ=10
08 00 00 8086 10D3 Ethernet,IRQ=5
09 00 00 8086 10D3 Ethernet,IRQ=10
0B 00 00 177D 0010 Cavium Encryp 8086 10D3 Ethernet,IRQ=11
0D 00 00 1A03 1150 PCI Bridge,IRQ=10
0E 00 00 1A03 2000 VGA,IRQ=10
FF 00 00 8086 2C61 Bridge Device
FF 00 01 8086 2D01 Bridge Device
FF 02 00 8086 2D10 Bridge Device
FF 02 01 8086 2D11 Bridge Device
FF 02 02 8086 2D12 Bridge Device
FF 02 03 8086 2D13 Bridge Device


Booting from ROMMON

Cisco Systems ROMMON Version (2.1(9)8) #1: Wed Oct 26 17:14:40 PDT 2011

 

Use BREAK or ESC to interrupt boot.
Use SPACE to begin boot immediately.
Boot interrupted.


=================================================================================


ciscoasa# show ver

Cisco Adaptive Security Appliance Software Version 9.8(4)10
Firepower Extensible Operating System Version 2.2(2.121)
Device Manager Version 7.15(1)150

Compiled on Tue 20-Aug-19 12:51 PDT by builders
System image file is "tftp://10.0.21.3/asa984-10-smp-k8.bin"
Config file at boot was "startup-config"

ciscoasa up 7 mins 13 secs

Hardware: ASA5512, 4096 MB RAM, CPU Clarkdale 2792 MHz, 1 CPU (2 cores)
ASA: 1654 MB RAM, 1 CPU (1 core)
Internal ATA Compact Flash, 4096MB
BIOS Flash MX25L6445E @ 0xffbb0000, 8192KB

Encryption hardware device : Cisco ASA Crypto on-board accelerator (revision 0x1)
Boot microcode : CNPx-MC-BOOT-2.00
SSL/IKE microcode : CNPx-MC-SSL-SB-PLUS-0005
IPSec microcode : CNPx-MC-IPSEC-MAIN-0026
Number of accelerators: 1
Baseboard Management Controller (revision 0x1) Firmware Version: 2.4


0: Int: Internal-Data0/0 : address is a03d.6f2c.e6aa, irq 11
1: Ext: GigabitEthernet0/0 : address is a03d.6f2c.e6ae, irq 10
2: Ext: GigabitEthernet0/1 : address is a03d.6f2c.e6ab, irq 10
3: Ext: GigabitEthernet0/2 : address is a03d.6f2c.e6af, irq 5
4: Ext: GigabitEthernet0/3 : address is a03d.6f2c.e6ac, irq 5
5: Ext: GigabitEthernet0/4 : address is a03d.6f2c.e6b0, irq 10
6: Ext: GigabitEthernet0/5 : address is a03d.6f2c.e6ad, irq 10
7: Int: Internal-Data0/1 : address is 0000.0001.0002, irq 0
8: Int: Internal-Control0/0 : address is 0000.0001.0001, irq 0
9: Int: Internal-Data0/2 : address is 0000.0001.0003, irq 0
10: Ext: Management0/0 : address is a03d.6f2c.e6aa, irq 0
11: Int: Internal-Data0/3 : address is 0000.0100.0001, irq 0

Licensed features for this platform:
Maximum Physical Interfaces : Unlimited perpetual
Maximum VLANs : 50 perpetual
Inside Hosts : Unlimited perpetual
Failover : Disabled perpetual
Encryption-DES : Enabled perpetual
Encryption-3DES-AES : Enabled perpetual
Security Contexts : 0 perpetual
Carrier : Disabled perpetual
AnyConnect Premium Peers : 2 perpetual
AnyConnect Essentials : Disabled perpetual
Other VPN Peers : 250 perpetual
Total VPN Peers : 250 perpetual
AnyConnect for Mobile : Disabled perpetual
AnyConnect for Cisco VPN Phone : Disabled perpetual
Advanced Endpoint Assessment : Disabled perpetual
Shared License : Disabled perpetual
Total TLS Proxy Sessions : 2 perpetual
Botnet Traffic Filter : Disabled perpetual
IPS Module : Disabled perpetual
Cluster : Disabled perpetual

This platform has a Base license.

Serial Number: XXXXXXXXXXX
Running Permanent Activation Key: 0xc00ad444 0xf81ec433 0x992331e0 0xd1d00cb8 0x0231cfad
Configuration register is 0x1

Image type : Release
Key version : A

Configuration last modified by enable_15 at 12:41:26.289 UTC Wed Jul 28 2021

 

В чём может быть причина?
добавлял орпеативу. Догнал до 8ГБ (больше не держит). (также заметил, что слот "А" не видится. Если туда что-то подключить - девайс вообще не грузится сходу)

 

обновился максимум до 
Cisco Adaptive Security Appliance Software Version 9.8(4)10
Firepower Extensible Operating System Version 2.2(2.121)
Device Manager Version 7.15(1)150

0 ОТВЕТОВ 0