本ドキュメントでは、RTOS を用いたWLC の復旧方法をご案内します。
### この作業を実施するにあたり、RTOS が必要となります。
### 必要に応じて、弊社TAC にサービスリクエストを申請し、RTOS をご取得下さい。
*** 注意事項 ***
- 本作業は、WLC のコンソールポート経由で実施して下さい。
- WLC2504 にて、作業をする際には、Port 1 とTFTP Server 間で疎通性があるかご確認下さい。
- WLC5508/5520 等サービスポートを持つWLC で作業をする際には、サービスポートとTFTP Server 間で疎通性があるかご確認下さい。
1.
WLC 起動時に、イメージが正常に読み込めず、Boot Loader Menu が
起動している事を確認して下さい。
また、Primary / Backup Image 共に、”Image not found” となっている事も合わせて
ご確認下さい。
============================================================
Boot Loader Menu
============================================================
1. Run primary image (Image not found) - Active
2. Run backup image (Image not found)
3. Change active boot image
4. Clear configuration
5. Format FLASH Drive
6. Manually update images
2.
弊社TAC より、提供された2つのファイルをTFTP Server 配下に置いて下さい。
(AS_5500_RTOS-7.0.250.0 / AS_5500_cavium_main-7.0.250.0)
* ご提供するバージョン/型番名が異なる可能性がございます。
3.
Boot Load Menu で “6” を入力し、WLC のIP address やTFTP Server のIP address を
設定して下さい。
Enter selection: 6
Launching...
Launching images...
init started: BusyBox v1.6.0 (2009-02-03 04:56:32 EST) multi-call binary
Mount failed for selinuxfs on /selinux: No such file or directory
starting pid 655, tty '': '/etc/init.d/rcS'
Use DHCP for ip configuration (Y/n)? n
Enter switch IP address: 192.168.1.100
By "switch", the boot loader means WLC
Enter switch netmask: 255.255.255.0
Enter switch gateway: 192.168.1.1
Enter TFTP server IP address: 192.168.1.157
You have entered:
IP Address : 192.168.1.100
Netmask : 255.255.255.0
Gateway : 192.168.1.1
Server Ip Addr : 192.168.5.157
Is this correct(y/N)? y
4.
各種IP address の設定が完了しましたら、RTOS のアップデートをするかどうか聞かれるため、
“y” を入力し、ファイル名等を入力して下さい。
!!! WARNING updating using .aes or unapproved files will disable this unit !!!
Do you want to update RTOS (y/N)? y
Do you want to update Primary Or Secondary Image (P/s)? P
Enter filename for RTOS update: AS_5500_RTOS-7.0.250.0
RTOS update Done
Enter filename for FP update: AS_5500_cavium_main-7.0.250.0
FP update Done
Do you want to update an AP image (y/N)? N
※bootloader のバージョンによっては FP の update が省略される場合があります。
5.
RTOS を読み込み、再起動後にWLC の初期セットアップウィザードが起動してきますので、
WLC のIP 等を設定して下さい。
6.
初期設定完了後、使用されたいバージョンにアップグレードして下さい。