取消
显示结果 
搜索替代 
您的意思是: 
cancel
公告

December 2020

December 2020

【原创】N3K-C3548P-XL ARP故障案例分享

2226
查看次数
30
有帮助
5
评论
故障描述:Nexus N3K-C3548P-XL设备突发所有服务器ARP学习不到,MAC地址可正常学习
故障分析:
N3K-01# show policy-map interface control-plane| in arp next 5
class-map copp-s-arp (match-any)
police pps 200
HW MatchedPackets 263510
SW Matched Packets 228528
正常情况下,HWSWmatchedpackets数值应该一致,表示没有drop
它们之间的差值表示COPPdropcounter,即当时在COPPdrop263510-228528=34982arp包。

问题处理过程:

思科官方文档描述:
UpgradePath to Cisco NX-OS Release 7.x
Install All isthe only option that supports upgrade and downgrade between releases. Upgradefrom Releases 6.0(2)A8(7b), 6.0(2)A8(8), 6.0(2)A8(9), and 7.0(3)I7(3) issupported.
The following limitations are applicable when youupgrade from Releases 7.0(3)I7(2) or later to the NX-OS Release 7.0(3)I7(6):
■ Ifa custom CoPP policy is applied after upgrading to Cisco NX-OS Release7.0(3)I7(2) or later, and if the Nexus 3548 switch is downgraded to Cisco NX-OSRelease 5.0, where changes to the CoPP policy are not permitted, the customCoPP policy is retained and cannot be modified.
copy r s and reload isnot a supported method for an upgrade.
■ You must run the setup script after youupgrade to Cisco NX-OS Release 7.0(3)I7(6).

■ ForCisco Nexus 3548 and 3548-X switches, you must compact the software imagebefore you upgrade from earlier releases to Cisco NX-OS Release 7.0(3)I7(6).For the Cisco Nexus 3538-XL switch, compaction is not required.

在(config)#模式下执行setup
F340.16.04-Nexus3500-3(config)# setup


---- Basic System Configuration Dialog ----

Thissetup utility will guide you through the basic configuration of
thesystem. Setup configures only enough connectivity for management
ofthe system.

*Note:setup is mainly used for configuring the system initially,
whenno configuration is present. So setup always assumes system
defaultsand not the current system configuration values.

PressEnter at anytime to skip a dialog. Use ctrl-c at anytime
toskip the remaining dialogs.

Wouldyou like to enter the basic configuration dialog (yes/no): yes


Create another login account (yes/no) : n

Configure read-only SNMP community string (yes/no) : n

Configure read-write SNMP community string (yes/no) : n

Enter the switch name : <<<<<<<<没有提示yes/no 的地方敲回车即可

Continue with Out-of-band (mgmt0) management configuration? (yes/no) : n

Configure the default gateway? (yes/no) : n

Enable the telnet service? (yes/no) : n

Enable the ssh service? (yes/no) : y

Type of ssh key you would like to generate (dsa/rsa) :

Configure the ntp server? (yes/no) : n

Configure default interface layer (L3/L2) [L2]:

Configure default switchport interface state (shut/noshut) [noshut]:

Configure CoPP System Policy Profile ( default / l2 / l3 ) [default]:

Thefollowing configuration will be applied:
no telnet server enable
system default switchport
no system default switchport shutdown
policy-map type control-plane copp-system-policy ( default )

Wouldyou like to edit the configuration? (yes/no) : n

Usethis configuration and save it? (yes/no) : y
MTC:Executingcopp config

[########################################]100% <<<<<
Copycomplete, now saving to disk (please wait)...
Copycomplete.
评论
one-time
Expert
感谢版主分享,谢谢~
CDB
Beginner
Beginner
进来瞧一瞧
bo chen
Beginner
干货满满,感谢分享
764963038cisco
Beginner
不错感谢分享
cz89792895qp0
Community Member
具体事什么意思,做的操作起到什么作用
不能显示该小部件。