取消
显示结果 
搜索替代 
您的意思是: 
cancel
公告

December 2020

1956
查看次数
0
有帮助
11
回复
sn270043685
Beginner

倒霉新手日记1815W之ME-Uboot 升级日志console

帖子比较长,大家慢慢看,
本人穷屌丝一个,想入手个能装ME系统的AP,某宝看了好久,260入手一个AP1815W
不懂就是罪呀,,没有电源接口,只能POE,接到2504控制器,也关联不上,
怎么复位都没有信号 ,本来想着接控制器能通TFTP结果一查还要直联,折腾半天,用电源接到网线上,网线一头插电脑一头插AP
用48V电源弄出来4根线给POE供电,
一看console又不是普通的口,我的妈呀,网上又查,各种万用表,量针角,,买TTL转USB(这里买错了应该买RS232转TTL)
回来一看,god!!!! 送的线太粗,这个针很小,接上不去,又一通折腾勉强能接上console
一看没有系统095907s4m4cm4rm4rhjrji.jpg095918wpdk33o85h4yt4ks.jpg
Booting from part1
Volume part1 not found!
Volume part1 not found!
Booting failed, try boot on part2
Volume part2 not found!
Volume part2 not found!
(BTLDR) #
又是各种查,
bootcmd=nandboot
u-boot>> setenv ipaddr 10.63.1.223
u-boot>> setenv netmask 255.255.255.0
u-boot>> setenv gatewayip 10.63.1.1
u-boot>> setenv serverip 10.63.20.52
u-boot>> saveenv
Saving Environment to SPI Flash...
Erasing SPI flash....Writing to SPI flash.....done
u-boot>>
u-boot>>
u-boot>>
u-boot>> tftp ap3g3-k9w8-tar.153-3.JF10.tar
一看大家都不成功,我也不成功,
没用任何用,又查了半天,
setenv bootfile AIR-AP1815-K9-ME-8-5-103-0.tar
boot tftp
启动不成功,
095918wosd3rfsn6s06don.jpg
又查又查了半天,说是需要把tar里的bin拿出来
setenv bootfile part.bin
boot tftp
终于启动了,结果我想拷进flash不知道怎么办了?又查,
ap-type mobility-express tftp://x.x.x.x/AIR-AP815i-K9-x.x.x.x.tar
用这个命令,提示已经是ME系统,无法升级
又查
archive download-sw /reload tftp://10.88.7.15/AIR-AP1830-K9-8.2.100.0.tar
用这个命令,结果还没拷到一半自动 成控制器模式,坑呀,新手的痛,!!!!!!!!!!!!
想配置控制器模式吧,配完之后要重启,IOS又没有了 FUCK!!!!!!!
又想办法下个瘦AP模式,
提取出来里面的BIN启动,
然后又重新使用
ap-type mobility-express
拷完之后*****看不懂了?!!!????还是无法启动,
AP707D.B97E.0BA8#ap-type mobility-express tftp://10.1.1.2/AIR-AP1815-K9-ME-8-10-130-0.tar
Starting download ME-AP image tftp://10.1.1.2/AIR-AP1815-K9-ME-8-10-130-0.tar ...
It may take a few minutes. If longer, please abort command, check network and try again.
######################################################################## 100.0%
Upgrading ...
do NO_UPGRADE, part2 is active part
do CHECK_ME, part2 is active part
upgrade.sh: Start doing upgrade arg1=CHECK_ME arg2=,from_cli arg3= ...
upgrade.sh: Using image /tmp/cli_part.tar on mallorca ...
Image signing verify success.
upgrade.sh: btldr version: AP ver 23, image ver 52
Verify returns 0
Unlocking /dev/mtd4 ...
Erasing /dev/mtd4 ...
23+0 records in
23+0 records out
upgrade.sh: btldr is updated successfully!
upgrade.sh: Copying to /storage/boot_part1: info
upgrade.sh: Copying to /storage/boot_part1: btldr_crete_md5
upgrade.sh: Copying to /storage/boot_part1: file_hashes
upgrade.sh: Copying to /storage/boot_part1: final_hash
upgrade.sh: Copying to /storage/boot_part1: btldr.bin.lzma
upgrade.sh: Copying to /storage/boot_part1: btldr_md5
upgrade.sh: Copying to /storage/boot_part1: btldr_crete.bin.lzma
upgrade.sh: Copying to /storage/boot_part1: info.ver
upgrade.sh: Copying to /storage/boot_part1: iosap_info
upgrade.sh: Done with copying mallorca btldr to /storage/boot_part1
upgrade.sh: part to upgrade is part1
upgrade.sh: AP version1: part1 , img 8.10.130.0
upgrade.sh: Updating UBI device...
libubi: error!: cannot get information about "/dev/ubivol/part1"
error 2 (No such file or directory)
ubiupdatevol: error!: error while probing "/dev/ubivol/part1"
error 2 (No such file or directory)
upgrade.sh: activate part1, set BOOT to part1
upgrade.sh: AP version2: part1 8.10.130.0, img 8.10.130.0
upgrade.sh: AP primary version: 8.10.130.0
upgrade.sh: Finished upgrade task.
upgrade.sh: Cleanup for do_upgrade...
upgrade.sh: /tmp/upgrade_in_progress cleaned
upgrade.sh: Cleanup tmp files ...
Successfully downloaded and setup ME-AP image.
Archive done.
AP707D.B97E.0BA8# Stopping WCPD process...
Stopping DHCPv6 client...
[ OK ] Stopped Stopping Cisco led service...
Stopping Cisco rtd service...
[ OK ] Stopped target Timers.
Stopping gRPC server daemon...
Stopping Slow CGI daemon...
Stopping capwapd...
[ OK ] Stopped System Monitor service.
[ OK ] Stopped Serial Getty on ttyS0.
[ OK ] Stopped Cisco led service.
[ OK ] Stopped Fast CGI daemon.
[ OK ] Stopped Hostapd process.
[ OK ] Stopped Cisco rtd service.
[ OK ] Stopped AP Trace daemon.
[ OK ] Stopped Clean Air daemon.
[ OK ] Stopped DNSmasq.
[ OK ] Stopped DHCPv6 client.
[ OK ] Stopped WCPD process.
[ OK ] Stopped Dropbear (SSH) server.
[ OK ] Stopped gRPC server daemon.
[ OK ] Stopped Slow CGI daemon.
[ OK ] Stopped capwapd.
[ OK ] Removed slice system-serial\x2dgetty.slice.
[ OK ] Stopped Pnp agent.
[ OK ] Stopped target Basic System.
[ OK ] Stopped target Paths.
[ OK ] Stopped target System Initialization.
[ OK ] Stopped Cisco Tam service.
Stopping Cisco Tam service...
Stopping Cisco klogd...
Stopping Cisco synclogd...
Stopping Cisco brain service...
Stopping Cisco printkd...
Stopping Cisco watchdog...
Stopping Cisco nolan service...
Stopping Cisco system time saving...
[ OK ] Stopped Cisco certtime service.
Stopping Cisco certtime service...
[ OK ] Stopped target Sockets.
[ OK ] Stopped target Slices.
[ OK ] Stopped Cisco klogd.
[ OK ] Stopped Cisco watchdog.
[ OK ] Stopped Cisco printkd.
[ OK ] Stopped Cisco synclogd.
[ OK ] Stopped Cisco brain service.
[ OK ] Stopped Cisco nolan service.
[ OK ] Stopped Cisco system time saving.
[ OK ] Stopped Cisco certificate create service.
Stopping Cisco certificate create service...
Stopping Cisco syslog service...
[ OK ] Stopped Cisco syslog service.
[ OK ] Stopped Cisco Kclick.
Stopping Cisco Kclick...
[ OK ] Stopped Cisco Kclick.
Stopping Cisco Kclick...
[ OK ] Stopped Cisco nss service.
Stopping Cisco nss service...
[ OK ] Stopped Cisco S10 boot service.
Stopping Cisco S10 boot service...
[ OK ] Stopped target Local File Systems.
Unmounting /pstore...
Unmounting /click...
[ OK ] Stopped Cisco act2 check.
Stopping Cisco act2 check...
Stopping Cisco seed generation...
Unmounting /sys/kernel/debug...
[ OK ] Stopped Cisco kexec.
Stopping Cisco kexec...
[ OK ] Stopped Cisco system time setup.
Stopping Cisco system time setup...
Unmounting /tmp...
[ OK ] Unmounted /pstore.
[ OK ] Unmounted /click.
[ OK ] Stopped Cisco seed generation.
[ OK ] Unmounted /sys/kernel/debug.
[ OK ] Unmounted /tmp.
[ OK ] Reached target Unmount All Filesystems.
[ OK ] Stopped target Local File Systems (Pre).
[ OK ] Stopped Cisco early mount.
Stopping Cisco early mount...
[ OK ] Stopped target Cisco File Systems (Pre).
[ OK ] Stopped Cisco UBIFS reformat/mount.
Stopping Cisco UBIFS reformat/mount...
[ OK ] Removed slice system.slice.
[ OK ] Removed slice -.slice.
[ OK ] Reached target Shutdown.
[06/03/2019 19:58:54.2899] reboot: Restart
Board type: AP1815W
smem ram ptable found: ver: 1 len: 3
U-Boot 2012.07 (btldr release 23) (Sep 28 2016 - 17:30:15)
This product contains some software licensed under the
"GNU General Public License, version 2" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
DRAM: 1022 MiB
Nand: Detected ONFI Macronix NAND 256MiB 3,3V 8-bit
SF: Detected MX25L3205D with page size 4 KiB, total 4 MiB
MFG data loaded
Scanning shenv data blocks
Total valid parts=4
Active shenv part[0:1], write_counter=6
machid: 8010001
Net: MAC0 addr:70:7d:b9:7e:b:a8
PHY ID1: 0x4d
PHY ID2: 0xd0b1
ipq40xx_ess_sw_init done
Warning: eth0 MAC addresses don't match:
Address in SROM is 70:7d:b9:7e:0b:a8
Address in environment is 00:03:7f:aa:aa:13
Found new boot image.
Validating new image integrity ... Passed.
Erasing current boot.
Erasing at 0x16f000 -- 100% complete.
Copy boot image ...
................................................................................................................................................................................................................................................................................
First validation passed.
Active new image.
................................
Second validation passed.
Disable backup copy ...
Erasing at 0x31f000 -- 100% complete.
Boot upgrade completed.
resetting ...
Board type: AP1815W
smem ram ptable found: ver: 1 len: 3
U-Boot 2012.07 (btldr release 51) (Oct 29 2019 - 06:43:09)
This product contains some software licensed under the
"GNU General Public License, version 2" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
DRAM: 1022 MiB
Nand: Detected ONFI Macronix NAND 256MiB 3,3V 8-bit
NAND ECC=4 ECC_THRESHOLD(NAND ECC-1)=3
SF: Detected MX25L3205D with page size 4 KiB, total 4 MiB
MFG data loaded
Scanning shenv data blocks
Total valid parts=4
Active shenv part[0:1], write_counter=6
machid: 8010001
Net: MAC0 addr:70:7d:b9:7e:b:a8
PHY ID1: 0x4d
PHY ID2: 0xd0b1
ipq40xx_ess_sw_init done
Warning: eth0 MAC addresses don't match:
Address in SROM is 70:7d:b9:7e:0b:a8
Address in environment is 00:03:7f:aa:aa:13
Auto boot mode, use bootipq directly
Hit ESC key to stop autoboot: 0
Specified BOOT: part1
Booting from part1
Volume part1 not found!
Volume part1 not found!
Booting failed, try boot on part2
Volume part2 not found!
Volume part2 not found!
(BTLDR) #
烦烦烦烦烦烦烦烦烦烦!!!!!!!!
大神呀哪位哪神知道什么原因,怎么查看 flash命令1!!!!我TM要疯了!!!
11 条回复11
wuhao0015
Rising star

看下我的日志。
https://blog.csdn.net/wuhao0015/article/details/106041966
看下在uboot下怎么启动。
sn270043685
Beginner

从TFTP启动瘦AAPIOS疯了控制器也连不上控制器地址 1.250
uccess rate is 100 percent (5/5), round-trip min/avg/max = 0.750/0.795/0.869 ms
AP707D.B97E.0BA8#[*01/01/2000 00:39:55.0099]
[*01/01/2000 00:39:55.0099] CAPWAP State: DTLS Teardown
[*01/01/2000 00:39:55.3299] do ABORT, part2 is active part
[*01/01/2000 00:39:55.3599] upgrade.sh: Cleanup tmp files ...
[*01/01/2000 00:39:59.7599] No more AP manager addresses remain..
[*01/01/2000 00:39:59.7599] No valid AP manager found for controller 'Cisco_d8:0b:c5' (ip: 10.1.1.250)
[*01/01/2000 00:39:59.7599] Failed to join controller Cisco_d8:0b:c5.
[*01/01/2000 00:39:59.7599] Failed to join controller.
[*01/01/2000 00:40:19.7699]
[*01/01/2000 00:40:19.7699] CAPWAP State: Discovery
[*01/01/2000 00:40:19.7899] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*01/01/2000 00:40:19.7899] Discovery Response from 10.1.1.250
[*01/01/2000 00:40:29.0000]
[*01/01/2000 00:40:29.0000] CAPWAP State: DTLS Setup
[*01/01/2000 00:40:29.0599] dtls_process_packet: DTLS Error: 1046
[*01/01/2000 00:40:29.0599] dtls_process_packet: The controller shut down the DTLS connection.
[*01/01/2000 00:40:29.0599] dtls_process_packet: Please verify that the AP certificate is valid and has not expired.
[*01/01/2000 00:41:26.0099]
[*01/01/2000 00:41:26.0099] CAPWAP State: DTLS Teardown
[*01/01/2000 00:41:26.2999] do ABORT, part2 is active part
[*01/01/2000 00:41:26.3299] upgrade.sh: Cleanup tmp files ...
[*01/01/2000 00:41:30.7699] No more AP manager addresses remain..
[*01/01/2000 00:41:30.7699] No valid AP manager found for controller 'Cisco_d8:0b:c5' (ip: 10.1.1.250)
[*01/01/2000 00:41:30.7699] Failed to join controller Cisco_d8:0b:c5.
[*01/01/2000 00:41:30.7699] Failed to join controller.
[*01/01/2000 00:41:50.7699]
[*01/01/2000 00:41:50.7699] CAPWAP State: Discovery
[*01/01/2000 00:41:50.7899] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*01/01/2000 00:41:50.7899] Discovery Response from 10.1.1.250
[*01/01/2000 00:42:00.0000]
[*01/01/2000 00:42:00.0000] CAPWAP State: DTLS Setup
[*01/01/2000 00:42:00.0599] dtls_process_packet: DTLS Error: 1046
[*01/01/2000 00:42:00.0599] dtls_process_packet: The controller shut down the DTLS connection.
[*01/01/2000 00:42:00.0599] dtls_process_packet: Please verify that the AP certificate is valid and has not expired.
[*01/01/2000 00:42:57.0099]
[*01/01/2000 00:42:57.0099] CAPWAP State: DTLS Teardown
[*01/01/2000 00:42:57.2999] do ABORT, part2 is active part
[*01/01/2000 00:42:57.3299] upgrade.sh: Cleanup tmp files ...
[*01/01/2000 00:42:58.6899] ethernet_port wired0, ip 10.1.1.52, netmask 255.255.255.0, gw 10.1.1.250, mtu 1500, bcast 10.1.1.255, dns1 10.1.1.250, vid 0, static_ip_failover true, dhcp_vlan_failover false
[*01/01/2000 00:43:01.7599] No more AP manager addresses remain..
[*01/01/2000 00:43:01.7599] No valid AP manager found for controller 'Cisco_d8:0b:c5' (ip: 10.1.1.250)
[*01/01/2000 00:43:01.7599] Failed to join controller Cisco_d8:0b:c5.
[*01/01/2000 00:43:01.7599] Failed to join controller.
[*01/01/2000 00:43:02.7799] AP IPv4 Address updated from 10.1.1.10 to 10.1.1.52
[*01/01/2000 00:43:03.7999] ethernet_port wired0, ip 10.1.1.10, netmask 255.255.255.0, gw 10.1.1.2, mtu 1500, bcast 10.1.1.255, dns1 0.0.0.0, is_static true, vid 0, static_ip_failover false, dhcp_vlan_failover false
[*01/01/2000 00:43:17.9999] AP IPv4 Address updated from 10.1.1.52 to 10.1.1.10
[*01/01/2000 00:43:21.7699]
[*01/01/2000 00:43:21.7699] CAPWAP State: Discovery
[*01/01/2000 00:43:21.7799] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*01/01/2000 00:43:21.7899] Discovery Response from 10.1.1.250
[*01/01/2000 00:43:21.7999] Cleanning up DTLS connection.
[*01/01/2000 00:43:21.7999]
[*01/01/2000 00:43:21.7999] CAPWAP State: DTLS Teardown
[*01/01/2000 00:43:22.1499] do ABORT, part2 is active part
[*01/01/2000 00:43:22.1699] upgrade.sh: Cleanup tmp files ...
[*01/01/2000 00:43:22.2399] Cleanning up DTLS connection.
[*01/01/2000 00:43:22.2399]
[*01/01/2000 00:43:22.2399] CAPWAP State: DTLS Teardown
[*01/01/2000 00:43:22.5299] do ABORT, part2 is active part
[*01/01/2000 00:43:22.5599] upgrade.sh: Cleanup tmp files ...
[*01/01/2000 00:43:36.8599]
[*01/01/2000 00:43:36.8599] CAPWAP State: Discovery
[*01/01/2000 00:43:36.8699] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*01/01/2000 00:43:36.8699] Discovery Response from 10.1.1.250
sn270043685
Beginner

wuhao0015 发表于 2020-11-27 10:48
看下我的日志。
https://blog.csdn.net/wuhao0015/article/details/106041966
看下在uboot下怎么启动。

是的你没看完,我已经启动了可是灌不进去IOS不可能永远都从TFTP启动
敏民
Beginner

这个升级固件很简单。首先你需要一根能敲命令的console线.....这就可以显示ap的现固件版本,掌握它的灵魂,就可敲命令升级固件了,我已搞定了N台这型号的,
敏民
Beginner

我己成功升级N台1815WAP这型号.没有你说的那么复杂...首先需要一根CONSOLE线.这就可显示AP版本..敲命令升级.....
VolcanoWolf
Beginner

TTL_VCC
TTL_GND
TTL_RXD
TTL_TXD在设备上的顺序能否提供下
wuhao0015
Rising star

感觉应该是设备故障。
Booting from part1
Volume part1 not found!
Volume part1 not found!
Booting failed, try boot on part2
Volume part2 not found!
Volume part2 not found!
(BTLDR) #
sn270043685
Beginner

CRB 发表于 2020-11-30 11:11
TTL_VCC
TTL_GND
TTL_RXD

最左VCC最右GND,全新包装1815W-Q-K9C,500元,需要联系我
iliaodong
Beginner

应该不是这样显示的~~你直接买个3602不就完结~~~便宜又耐用,我们一直用它~
mingfenggao97627
Beginner

1815w配置很低的,还不如1810W
huajiang
Beginner

学习了学习了
Content for Community-Ad