点对点连接

[zhanlei80]

如上图是我想要做成的效果

瘦ap(1542-2)连接胖ap(1542-1)连接失败，请帮助分析连接失败原因，下面是瘦ap返回代码

AP7488.BB1D.C25A#[*06/01/2023 10:00:21.9744] AP IPv4 Address updated from 0.0.0.0 to 192.168.0.20
[*06/01/2023 10:00:21.9807] send CAPWAP ctrl msg to the socket<30>systemd[1]: Starting Core Files Uploader Watcher...
[*06/01/2023 10:00:21.9829] : Socket operation on non-socket
[*06/01/2023 10:00:23.3910] dtls_init: Use SUDI certificate
[*06/01/2023 10:00:23.3931]
[*06/01/2023 10:00:23.3931] CAPWAP State: Init
[*06/01/2023 10:00:23.3951]
[*06/01/2023 10:00:23.3951] CAPWAP State: Discovery
[*06/01/2023 10:00:23.4165] Discovery Request sent to 192.168.0.10, discovery type STATIC_CONFIG(1)
[*06/01/2023 10:00:23.4180] Discovery Request sent to 192.168.0.10, discovery type STATIC_CONFIG(1)
[*06/01/2023 10:00:23.4192] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*06/01/2023 10:00:23.4195]
[*06/01/2023 10:00:23.4195] CAPWAP State: Discovery
[*06/01/2023 10:00:28.1525] Start: RPC thread 1951079408 created.
[*06/01/2023 10:00:52.9066]
[*06/01/2023 10:00:52.9067] CAPWAP State: Discovery
[*06/01/2023 10:00:52.9326] Discovery Request sent to 192.168.0.10, discovery type STATIC_CONFIG(1)
[*06/01/2023 10:00:52.9350] Discovery Request sent to 192.168.0.10, discovery type STATIC_CONFIG(1)
[*06/01/2023 10:00:52.9367] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*06/01/2023 10:01:22.3686]
[*06/01/2023 10:01:22.3686] CAPWAP State: Discovery
[*06/01/2023 10:01:22.3707] Discovery Request sent to 192.168.0.10, discovery type STATIC_CONFIG(1)
[*06/01/2023 10:01:22.3945] Discovery Request sent to 192.168.0.10, discovery type STATIC_CONFIG(1)
[*06/01/2023 10:01:22.3989] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)

注：已在胖ap设置瘦ap mac为白名单了，谢谢！

[Rps-Cheers]

看你的需求时想要配置WGB，可以参考下相关配置指南，看看是否配置有问题？

https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-1/configuration-guide/b_cg81/workgroup_bridges.pdf

https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-10/config-guide/b_cg810/workgroup_bridges.html

[zhanlei80]

目前是按照此文档配置的

https://www.cisco.com/c/zh_cn/support/docs/wireless/mobility-express-aironet-access-points/215077-configuring-point-to-point-mesh-link-wit.html

配置中，瘦ap（192.168.0.20）无法连接胖ap（192.168.0.10）

[Rps-Cheers]

了解，如已经比较明确部署方式的话，那就可以根据该链接的建议来。

从弹出的logging来看，是没有收到任何控制器的回复的。

[*06/01/2023 10:00:23.4165] Discovery Request sent to 192.168.0.10, discovery type STATIC_CONFIG(1)
[*06/01/2023 10:00:23.4180] Discovery Request sent to 192.168.0.10, discovery type STATIC_CONFIG(1)
[*06/01/2023 10:00:23.4192] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)

目前RAP可以ping ME模式的AP的management interface吗？另外，MAP（internal ap的模式是否有转换）可以检查一下IP等信息是否OK。控制器和AP的版本是否一致了。

《controller界面》

show int summ

sho ap summ

show mesh ap summ

show sysinfo

《internal ap界面/MAP》

sho ver

show capwap client rcb

show capwap client config

其他如需debug或者问题的提示等内容，还请着重看一下“故障排除”和“提示、技巧和常见错误”等内容了。

[zhanlei80]

设置后，应建立网状链路。为了使MAP后面的有线客户端通过网状链路传递流量，需要在MAP上的“无线设置”>“接入点”>“MAP”>“网状”下启用以太网桥接：

这句话表示Map也是需要刷成胖ap吗？

[Rps-Cheers]

Mesh AP是lightweight ap就行，不过是需要转换成flex-bridge的模式。

上面那句话是指启用以太网桥接，是为了让laptop2通信

[zhanlei80]

转换成flex-bridge命令是什么？capwap ap model ???

[Rps-Cheers · Accepted solution]

是的，是这个命令：

MAP# capwap ap mode flex-bridge

[zhanlei80]

模式没有调整，但刚才重启瘦ap后，能在胖ap控制台搜索到瘦ap后，再在控制台中将瘦ap设置为桥接，就能连通了

[Rps-Cheers]

可以，很高兴问题能够得到解决。