取消
显示结果 
搜索替代 
您的意思是: 
cancel
27130
查看次数
10
有帮助
11
回复

求大哥指点AP登录问题AIR--CAP2602I-C-K9

wongmin2015
Level 1
Level 1
遇到一个工程需要搭建一个无线局域网,我购买了2个Air-Cap2602i-c-k9和SF90D-08,因为第一次用,安装思科官网的配置指南用超级终端修改AP的IP地址,不知道怎么进入特权模式(没有看到在哪里登录或者修改模式的),求各位大哥给点意见.(工程现在就差无线网就可以调试了,所有比较急).下面给出超级终端收到的信息,请大哥们帮忙分析分析,拜谢

IOS Bootloader - Starting system.
flash is writable
FLASH CHIP: Macronix Mirrorbit (00C2)
Xmodem file system is available.
flashfs[0]: 10 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 7207936
flashfs[0]: Bytes available: 24790016
flashfs[0]: flashfs fsck took 14 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: b8:38:61:ba:70:4e
Ethernet speed is 100 Mb - FULL Duplex
Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx"...###########################
File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 10 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 7207936
flashfs[0]: Bytes available: 24790016
flashfs[0]: flashfs fsck took 7 seconds.
Base Ethernet MAC address: b8:38:61:ba:70:4e
Boot CMD: 'boot flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx'
Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"...#####################
File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx" uncompressed and installed, entr
y point: 0x2003000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C2600 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JA1, RELEAS
E SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 30-Jul-13 23:08 by prod_rel_team
Initializing flashfs...
flashfs[2]: 10 files, 2 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31739904
flashfs[2]: Bytes used: 7207936
flashfs[2]: Bytes available: 24531968
flashfs[2]: flashfs fsck took 8 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 11999232
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 11998208
flashfs[3]: flashfs fsck took 0 seconds.
flashfs[3]: Initialization complete.
Copying radio files from flash: to ram:
%Error opening flash:/ap3g2-rcvk9w8-mx/E2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/B2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/V2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/X2.bin (No such file or directory)
%Error opening flash:/ap3g2-rcvk9w8-mx/Y2.bin (No such file or directory)
Uncompressing radio files...
File not found: flash:/ap3g2-rcvk9w8-mx/8004.img
File not found: flash:/ap3g2-rcvk9w8-mx/E5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/B5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/V5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/X5.bin
File not found: flash:/ap3g2-rcvk9w8-mx/Y5.bin
...done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
no ip http server
^
% Invalid input detected at '^' marker.
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco AIR-CAP2602I-C-K9 (PowerPC) processor (revision A0) with 180214K/81920K by
tes of memory.
Processor board ID FGL1804WAZJ
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.5.1.73
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: B8:38:61:BA:70:4E
Part Number : 73-14588-03
PCA Assembly Number : 800-37899-01
PCA Revision Number : B0
PCB Serial Number : FOC18037793
Top Assembly Part Number : 800-38356-01
Top Assembly Serial Number : FGL1804WAZJ
Top Revision Number : A0
Product/Model Number : AIR-CAP2602I-C-K9
% Please define a domain-name first.
logging facility kern
^
% Invalid input detected at '^' marker.
logging trap emergencies
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
*Mar 1 00:00:11.323: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:13.019: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:13.607: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2600 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JA1, RELEAS
E SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 30-Jul-13 23:08 by prod_rel_team
*Mar 1 00:00:13.639: %CDP_PD-4-POWER_OK: All radios disabled - AC_ADAPTOR inlin
e power source
*Mar 1 00:00:13.647: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:13.651: %CAPWAP-3-ERRORLOG: Failed to load configuration from flas
h. Resetting to default config
*Mar 1 00:00:13.655: %PARSER-4-BADCFG: Unexpected end of configuration file.
lwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:14.635: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
ged state to up
*Mar 1 00:00:16.347: DPAA Initialization Complete
*Mar 1 00:00:16.347: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exite
d
*Mar 1 00:00:16.771: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
1 个已接受解答

已接受的解答

Xin Lei
Spotlight
Spotlight
出厂一般默认瘦AP;你需要转为胖AP才可以使用;
1、用网线连接AP的RJ45口,设置本地电脑网卡IP为10.0.0.2 255.255.255.252 (这个是默认的掩码,可以进入AP:控制台下自己改)
1、对于你想要转换的AP设备找到合适的IOS,如 我转换的是LAP1130 需要先找到胖AP的IOS。
2、重命名该文件名为 c1130-k9w7-tar.default
3、给AP断电,然后按住MODE 按钮不放
4、加电后看到超级终端提示 button is pressed, wait for button to be released..
5、松开mode 键,会进入自动搜索过程
button pressed for 26 seconds
process_config_recovery: set IP address and config to default 10.0.0.1
process_config_recovery: image recovery
image_recovery: Download default IOS tar image tftp://255.255.255.255/c1130-k9w7-tar.default
examining image...
extracting info (275 bytes)
Image info:
Version Suffix: k9w7-.124-10b.JA3
Image Name: c1130-k9w7-mx.124-10b.JA3
Version Directory: c1130-k9w7-mx.124-10b.JA3
这是搜索成功的提示,后面自动解压缩镜像并安装
7、检查一下flash,文件是否复制好;
ap: dir flash:
8、输入boot启动AP:
ap:boot

在原帖中查看解决方案

11 条回复11

Xin Lei
Spotlight
Spotlight
出厂一般默认瘦AP;你需要转为胖AP才可以使用;
1、用网线连接AP的RJ45口,设置本地电脑网卡IP为10.0.0.2 255.255.255.252 (这个是默认的掩码,可以进入AP:控制台下自己改)
1、对于你想要转换的AP设备找到合适的IOS,如 我转换的是LAP1130 需要先找到胖AP的IOS。
2、重命名该文件名为 c1130-k9w7-tar.default
3、给AP断电,然后按住MODE 按钮不放
4、加电后看到超级终端提示 button is pressed, wait for button to be released..
5、松开mode 键,会进入自动搜索过程
button pressed for 26 seconds
process_config_recovery: set IP address and config to default 10.0.0.1
process_config_recovery: image recovery
image_recovery: Download default IOS tar image tftp://255.255.255.255/c1130-k9w7-tar.default
examining image...
extracting info (275 bytes)
Image info:
Version Suffix: k9w7-.124-10b.JA3
Image Name: c1130-k9w7-mx.124-10b.JA3
Version Directory: c1130-k9w7-mx.124-10b.JA3
这是搜索成功的提示,后面自动解压缩镜像并安装
7、检查一下flash,文件是否复制好;
ap: dir flash:
8、输入boot启动AP:
ap:boot

wongmin2015
Level 1
Level 1
顶贴求支持

jing zhang
Level 1
Level 1
你这个是瘦AP,有无线控制器么?
如果没有需要降级成胖AP的……

wongmin2015
Level 1
Level 1
thousandmoun 发表于 2015-4-12 12:13 back.gif
你这个是瘦AP,有无线控制器么?
如果没有需要降级成胖AP的……

大哥,无线控制器怎么看,怎么降级的

wongmin2015
Level 1
Level 1
thousandmoun 发表于 2015-4-12 12:13 back.gif
你这个是瘦AP,有无线控制器么?
如果没有需要降级成胖AP的……

电脑服务器连到SF90D-08以太网交换机上,交换机接的AP

jing zhang
Level 1
Level 1
打开TFTP工具,准备好胖AP的IOS(如ap3g2-k9w7-tar.152-4.JA1.tar,把他重命名为ap3g2-k9w7-tar.default)放到TFTP的跟目录下,将TFTP服务器的IP地址改成10.0.0.2到10.0.0.254中任意一个;
然后在关闭AP电源,按住Mode键再开电源,直到AP上出现为一个常亮的红灯,松开mode键,让AP自动下载IOS就可以了,AP本身的默认IP地址为10.0.0.1。

wongmin2015
Level 1
Level 1
thousandmoun 发表于 2015-4-12 16:38 back.gif
打开TFTP工具,准备好胖AP的IOS(如ap3g2-k9w7-tar.152-4.JA1.tar,把他重命名为ap3g2-k9w7-tar.default)放 ...

谢谢你的帮助,我想我明白了.那么另一个问题我的是2602i的,请问你有能让我升级的胖AP的IOS文件吗?我邮箱是wongmin2015@163.com,谢谢

wongmin2015
Level 1
Level 1
sunlui820522 发表于 2015-4-12 16:46 back.gif
出厂一般默认瘦AP;你需要转为胖AP才可以使用;
1、用网线连接AP的RJ45口,设置本地电脑网卡IP为10.0.0. ...

大哥,你的回答对我非常有用,非常感谢你.请问大哥你有能供我2602I升级的IOS文件吗?或者你可以告诉我怎么去获得这样的文件.我的邮箱是wongmin2015@163.com,感谢你

Xin Lei
Spotlight
Spotlight
本帖最后由 sunlui820522 于 2015-4-13 20:33 编辑
wongmin2015 发表于 2015-4-13 10:07 back.gif
大哥,你的回答对我非常有用,非常感谢你.请问大哥你有能供我2602I升级的IOS文件吗?或者你可以告诉我怎么去 ...

用你的思科账号登陆以下网址可以下载;
https://software.cisco.com/download/release.html?mdfid=284362257&flowid=34153&softwareid=284180979&release=15.3.3-JAB&relind=AVAILABLE&rellifecycle=ED&reltype=latest

yttbxrsxu8095
Level 1
Level 1
精英 们:
我还是下载不了这个IOS文件,没有权限下载呀!!!!!。。。。。。。。。谁有能不能发一份到我的邮箱,万分感谢!!!43852530@qq.com

yttbxrsxu8095
Level 1
Level 1
下载不了,提示没有权限,我也是刚注册的帐号,哪位有的能不能帮忙发一份到我拉邮箱!!!!谢谢!!! 43852530@qq.com
入门指南

使用上面的搜索栏输入关键字、短语或问题,搜索问题的答案。

我们希望您在这里的旅程尽可能顺利,因此这里有一些链接可以帮助您快速熟悉思科社区:









快捷链接