Hello - I need help to get a script for Deploying Static EPG in VPC interface. The equivalent CLI configuration is below vpc context leaf 2471 2481 interface vpc VPC-TO-APPSERVER switchport trunk allowed vlan 200 tenant PROD application AP_SERVER e...
Forum Posts
Hi, I'm trying to do a service-graph with a Forti-VM. When I configure my device, I get No mgmt ip found for LDevVip. I have configured an IP address as you can see on my screen shot and the leaf pings the Forti. There's no problem of connectivity.Wh...
In the aci_contract_subject module I can find no way to set "apply both directions" to false. Also how does this ever work if we have defined a provider and a consumer. I can only guess a consumer cannot initiate a connection??
Resolved! Layer 2 Multicast configuration
could someone guide me to enable Layer 2 multicast only on Leaf ports connected to vRail servers. I see that PIM is required when We needed routing and for between different bridge domains. for Layer 2, what all settings I needed to enable and how th...
Hello all, I am hoping I can get some assistance on this. I am doing some testing with Inter-VRF Transit Routing and am having problems learning my routes on either VRF. Here is my topology: VRF1 - BGP L3Out Networks: VRF2 - OSPF L3Out Netw...
APIC discovered only one of eight Leaf and Spine Switches. The apics do not have the CIMC port cabled, and has only one ethernet/oob mgmt port connected. On the CIMC, I've verified lldp disabled and the nic is in dedicated mode. Apics have formed...
Hello, I have configured 2 different L3outs with interfaces on the same leafs. However, all routes that should be advertised only to the first L3out are being advertised also to the second one without adding it to the associated L3 in the bridge doma...
Resolved! Looking for ACI CVD Deployment Guide
Hi Freinds Looking for ACI CVD Deployment Guide , pls post the link as i didn't find thanks
Dear Community, at the moment i am struggeling to debug protocols on ACI. When i do the following commands on the CLI, i got no output: debug bgp ipv6 unicast / debug ospfv3 adjacency / debug bfd errors etc.. I ask because the fault on the GUI is no...
Hi, Just curious if anyone has found a tool/utility in ACI that can be used to check if ports are open on remote devices. Such as telnetting on a port? This was always a useful tool to me on non-ACI equipment so it would be a shame if Cisco deprecia...
Resolved! How to downgrade the ACI-Mode OS.
Hello, I am currently using APIC 2.3 (1i), Spine / Leaf 12.3.1i.I'm trying to add a new leaf switch, but the new leaf switch is version 14.0.So I will downgrade from version 14.0 to version 12.3.1i and add it to the fabric. The NX-OS Upgrade / downgr...
Are the Cisco Nexus 93180YC-FX 25G ports compliant with the 25G Consortium and/or IEEE standard ?
Hello - Can anybody help me to know what is the meaning of PC ID in the output of the command "show vpc map". I attached a simple diagram for reference. APIC# show vpc map VPC-TO-ROUTER1virtual port-channel Name domain Virtual IP Peer IP VPC ...
Hi!I have a Cisco APIC fabric with one ACI controller, two leaf swethes and one spine switch with version 3.2 (1m). And I decided to upgrade my fabric and now I have a 4.1(1j) version. I successfully upgraded APIC fabric but now from the APIC CLI I c...
Hello experts, I have a question for you, do you know a tool that allow us to convert Cisco ASA rules to filters in ACI ? because i have a lot of ACLs in ASA and it's difficult to covert all this rules manually. My second question is about Tufin int...
