Hello Cisco Community -I just encountered this "Interface configured as L2" fault when configuring a new L3Out (routed sub-interfaces).As soon as I unchecked "The Infrastructure VLAN has been enabled on the AEP" under the AEP configuration, the fault...
hi, need help to configure L3 out OSPF. I got an error when configuring external L3. what is the meaning of oper.state missing ? thanks
Dear all, I'm having a trouble with ACI when receiving TCN BPDU. I have 2 VPC that is connecting ACI leafs to 2 VSS switch (using 2VPC). I understand that whenever I migrate servers from legacy switch to ACI leaf, legacy switch will generate TCN and ...
ACI PathTenants > Networking > External Routed Networks >In the area with the routing protocol check boxes, there are a few options such as BGP, OSPF, and EIGRP.In this image, BGP and OSPF have been enabled.What is the equivalent CLI command for this...
In APIC, the implementation of AAA can be seen in the following path:APIC > ADMIN > AAA > RADIUS Management > RADIUS Providers APIC > ADMIN > AAA > TACACS+ Management > TACACS+ Providers*Image from https://www.cisco.com/c/en/us/td/docs/switches/datac...
Hi,I’m trying to configure smart licensing in Cisco ACI.We have the Premier licenses for all leafs. ACI is registered and authorized successfully with Smart Software Manager Satellite.The problem is, that all leafes are now authorized with the "base ...
In APIC, the status (enabled/disabled) of HTTP, HTTPS, SSH, and Telnet state can be viewed in the following path:APIC > Fabric > Fabric Policies > Pod Policies > Policies > Management AccessWhat is the equivalent command for this? I need to get this ...
Hello guysI was setting up 2 Fabrics today.#1 is already set up and upgraded with a little bit of pain and reloading and manual help, but it is up and active and alive. #2 Fabric behaves like this.Apic sees first leaf, I registered it for the first t...
Hi All, I want asking about problem with APIC and how to resolve it.Let's say, I have three APIC Controller in fabric and all of the fabric go down.1. what happens when all apic controllers in fabric go down?2. How to troubleshoot this problem?3. If ...
Good afternoon, we are running aci on a datacenter site, so we have 1 fabric at the moment. We’ll have probably a second fabric on a 2nd DC which will run his own apic cluster. In this case, we can use same node id for each node across both fabric...
Hello Friends, I am trying to digest concept of L4-L7 feature in ACI if i understood correct, if we use ASAv in L4-l7, then we dont need physical ASA in network to filter port traffic and ACI l4-l7 ASAv will do port based filtering ? Is it?If we use ...
Hi, The ACI Multi-pod white paper explains how remote endpoints belonging to different pods are associated to the spines Anycast VTEP address (Proxy), minimising the number of MP-BGP EVPN updates between pods when the endpoint performs local movement...
Hello Guys,My Cisco ACI fabric have 1 APIC server-M2 (Fimware 2.2(2e)), 1 Spine N9K-9336PQ, 2 Leaf N9K-9396PX using fimware 12.2(2e). can i upgrade my apic fimware to 4.2(3i), spine and leaf fimware to 14.2(3i) ?
If DC site has Cisco ACI switching infrastructure and DR site has non-ACI (Nexus 7K/5K/2K) switching infrastructure, could this impact RTO and RPO? Regards,Mukesh Pal
Hello guys, I have a question as follows:can I integrate checkpoint firewall into ACI in one-arm mode to make L4-L7 SG with PBR for east-west and north-sourth traffic?
