Is there a way to add description (that will appear on CLI "show interface description") to mgmt0 using the APIC v6 GUI?I'm seeing posts that talk to API and CLI methods. Our operations team will only use the GUI to configure, and the CLI only to in...
Forum Posts
I am following on this document Cisco APIC M1/M2/M3/L1/L2/M3 to M4/L4 Cluster Migration, Release 5.3(1) - Cisco to replace APIC-M2 with APIC-M4.It suggests that "...When you decommission a Cisco APIC, the APIC loses all fault, event, and audit log hi...
I'm having trouble seeing where to enable cdp and lldp on the oob/mgmt0 interfaces in the fabric; can anyone help?
One of my APIC server has rfs2_enc storage at 90%. I wipe the server clean and added back to cluster but this iss
Resolved! replace gen 1 ACI spine with new model
Hi, We are currently running a multi-pod fabric (version 4.2.7), with N9K-C9336PQ spine switches. New spines will be the N9K-C9316D-GX I am trying to find a procedure for this swap and also for specific tips and tricks. Especially I would like to he...
Hello, I have just added a standby controller (apic version 6) to a 3 node active apic cluster. under the standby controllers section, I can see everything seems okay, when going into the node 21, I see the operational state of the standby controller...
Hello Cisco community,I would like to request support from the community, I'm running in a blocking situation where I cannot finish the first setup because I'm blocked in the Setp #11, configuration of the NTP SERVER SETTINGS (Image attached).Every t...
Hi guys, Up until now I've had a very basic ACI deployment with everything I'd needed to do existing in a single physical domain and VLAN pool. Things have gotten a bit complicated. Basics are: 1. I have attached untagged traffic (i.e. VLAN 1) on spe...
Hello , Did Someone have a Logic Explanation , why we use the PI Vlan (Internal Vlan) on ACI? and What is the Role of PI Vlan ? i Know That the FD (Forwarding Vlan ) have always To be maped to an PI vlan , but the Question is Why ? and Why we need...
Hi everyone - I was looking into the documentation for FabricNode and saw two fields revealing the status of the node: AdSt and FabricSt AdSt defined as: The administrative state of the node.FabricSt as: Fabric state of the node Can anyone point me t...
Hi guys,About a month or so I've been facing the event with code E4208077 with a frequency of 1 minute. I could not find it anywhere by the description and the code. Does anyone faced the same and know what it can be related to?Thenk you.Description:...
I am trying to capture (either in APIC Dashboard or through a command) the down status of all leaf interfaces in APIC. I believe it is possible through "moquery" command. Please advice.
Hi,So i fired up ACI Simulator using ProxMox Hypervisor.I have set my static IP as follow:IPv4 address: 192.168.1.200/24Gateway: 192.168.1.1the IP address is free and available in my network.The subnet is correct.The gateway is correct.However, i can...
Resolved! SFP inventory from ACI Fabric
Hi all, I need to inventory the SPF plugged in the SPINE and LEAF of our ACI Fabric, but didn't find a menu where i can check that information, Anyone knows if is it possible to get that information consolidated? Our Fabric is version 2.1(2g) Thank...
Resolved! ACI: Automate EPG static port deployment
Hi ACI professionals,I want to automate the provisioning (and removal) of EPG static ports using the REST-API. My goal is, that the input parameter is the Leaf interface policy group name and the target encapsulation: vPC: infraAccBndlGrp.nameLeaf ac...
