Application Centric Infrastructure

Resolved! VMM Intergration - Multiple DVS ?

Hello All Our VMware Infra is divided into multiple clusters within single VMware Datacenter. We plan to use one DVS per Cluster, which means multiple DVS under on datacenter. When VMM integration is done between vCenter and APIC - Q1) do we have to...

Resolved! Upgrade 1.0(1n) to 1.0(2j)

I'm in the midst of upgrading my lab APICs from 1.0(1n) to 1.0(2j). When checking the status at the CLI i see the following output: Node-Id Role Current-Firmware Target-Firmware Upgrade-Status Progress-Percent(if inprogress)------------------------...

Resolved! ACI APIC failed to discover directly connected leaf nodes

I have successfully brought up the first APIC of an ACI fabric. It is running 2.2(1o). I have a pair of N938108TC-EX connected by the APIC, and managed to use lldp to detect them. Example below. Just have no idea why I cannot see this new node dis...

ASAv

Hi using ACI APIC the ASAv firewall log can be seen, the real time log?, anybody did this or any idea ?, my understanding using only ADSM only firewall logs can be seen reg V.Muthu

Resolved! ACI multi-pod: Access to non seed pod

Hello, We are currently doing labs with ACI. Does anyone know if it is possible to connect with the APIC through the infra tenant to another pods TEP (Pod2, 10.201.0.0/16 in our case) that is not the seed pod? It works fine in the seed-pod (Pod 1, 1...

How to configure Backup of Fabric in Cisco ACI

I am trying to take the backup of my ACI fabric to remote destination. Steps what I am following:- 1)Admin>Import/Export>Export Policies>Configuration right click create new config file put the Backup server policy under remote location and Start now...

Resolved! CISCO ACI - Port Channel

Hi, I was looking to get the command to see the bandwidth available in port-channel on ACI. But unfortunately not able to find same. Basically i was looking for below command available in catalyst sh int port-channel 1Port-channel1 is up, line proto...

Multiple ESXI with VPC/PC

Hi all I would like some advice about the best pratices to define a VPC with multiple ESXi, vlan and on 2 Datacenters my architecture is 4 leafs (2 on each DCs) leaf 1,2 then 3 and 412 ESXi (6 on each DCs)For each Esxi I have 4 10G splitted in 2 Por...

ASAv not rendering Parameters correctly in APIC GUI.

Just wondering if anyone can assist with the following issue. I have integrated an ASAv version 9.5.1 with device package .1.2.4.8. the APIC is currently running 2.2(1n). The device status is 'Stable'. However, if i navigate to the parameters tab...

ASAV on cisco aci

Hello ,I'm currently trying to implement asav on cisco aci , I created my device , created my instance graph. I have no faults at all but my devices does not appear in the deployed graph tab. And the ip address configured in this graph are not pushed...

ACI - routing protocol configration? why so complex? any easy way to remember steps?

is there any easy way to remember steps to configure routing protocols? it involves a lot of steps and its very hard to remember it. I have been thinking why did they made it so difficult to configure routing protocols in ACI? please suggest an easy...

Resolved! FCoE topology

I am referring to Fig 9 of http://www.cisco.com/c/en/us/td/docs/switches/datacenter/aci/apic/sw/2-x/basic_config/b_APIC_Basic_Config_Guide_2_x/b_APIC_Basic_Config_Guide_2_x_chapter_0100.html#id_21541 Q. Is it possible to connect servers with FCoE on ...

How to disable snmp trap on link status change on ACI switch ports ?

Hi While it is a simple job to disable snmp trap on a Nexus switch port using "no snmp trap link-status", I find it hard to configure similar on APIC. Kindly give me some idea. Thanks a lot!! Regards Clement

Does Fabricpath have a future when compared to ACI / VXLAN MP-BGP EVPN??

Hi, I'm studying for the CCDP exam and I am taking in alot of new concepts, I have started looking into fabircpath but this seems like its going to be a non-starter when compared with technologies such as VXLAN with the MP-BGP-EVN control plane - e...

border leaf for service appliance

are the max number of border leaves are five, cxan bord leaf connect to service appliance besides compute,storage ? thanks

Application Centric Infrastructure

Forum Posts

Resolved! VMM Intergration - Multiple DVS ?

Resolved! Upgrade 1.0(1n) to 1.0(2j)

Resolved! ACI APIC failed to discover directly connected leaf nodes

ASAv

Resolved! ACI multi-pod: Access to non seed pod

How to configure Backup of Fabric in Cisco ACI

Resolved! CISCO ACI - Port Channel

Multiple ESXI with VPC/PC

ASAv not rendering Parameters correctly in APIC GUI.

ASAV on cisco aci

ACI - routing protocol configration? why so complex? any easy way to remember steps?

Resolved! FCoE topology

How to disable snmp trap on link status change on ACI switch ports ?

Does Fabricpath have a future when compared to ACI / VXLAN MP-BGP EVPN??

border leaf for service appliance

Change normal contract to vzAny Contract

remote Leaf Uplink specefications

ACI Simulator ver-5.2-4d, Leaf and Spin are inactive state.

Contract limitations regarding the Consumers and Providers limits

ACI Node-Role TLV in LLDP Packets

Cisco ACI with Fortigate Multipod Cluser

Loop L2-Migration Legacy FabricPath to ACI

Cisco ACI - Impossible to delete objects created by Apic VPC Wizard

Extending Spine to IPN connections breaks inter-pod communication

How to use Object Store URL on APIC cli