Application Centric Infrastructure

Resolved! why APIC Fabirc interface is not UP

Hi, Team Need your help , our LAB APICs were connected to leaf switch by using 10G fiber connections and APICs were discovering fine.but since we have 1G copper SFP , we are try to replace fiber with the copper. but after swap , nothing is working. I...

Resolved! EPG associate with physical domain

Hello, I'm not clear why/when we need to associate a physical domain with an EPG? Without associate the EPG with a physical domain, the EPG can pass the traffic OK through static path binding. The front panel ports can get active vlans from AEP->doma...

Is cisco VSUM 1.2.2 compatible with esxi 6.0?

Is the latest cisco VSUM 1.2.2 which release on 7-May-2015 compatible with esxi 6.0?

Cisco ACI QoS

Guys, Is there a way a can police traffic on ACI. I need to limit traffic on a particular EPG, i know i can create a custom QoS policy but not sure how i can rate limit it.I figured i could probably mark the traffic and then send into 7k and police ...

Resolved! where to get cobra library to import in aci python samples

HiI have downloaded ACI Python samples provided by cisco on github. I searched using Python pip search for cobra but couldn't find any relevant library. Please let me know where could I get the python cobra library for ACI samples. Many Thanks Mehran

ACI Simulator: Cannot ping out from Leaf1 to External Network

Hello,We have a loaner ACI simulator UCSC-220 box which we have installed the simulator software on, however we are having trouble getting it fully configured and usable. Each of the 3 APICs have been configured with IP addresses, following the inst...

Resolved! max delay for stretched ACI fabric

Hi, ...regarding the limitation of a stretched ACI Fabric of 30km's - what's the max delay tolerated by the solution?When using a DWDM system, longer distances might be possible, if delay's are still acceptable? Thanks, Andy

Resolved! Cisco ACI maximums

Hi There, Could anyone help me find out the maximum tenants can setup in Cisco ACI. My understanding is it can support 64k tenants base on document below. however someone said it only support 100 tenants and it will grow to 500 in the future. Could ...

Resolved! Intra VRF Route Leaking

I need to route leak between VRFs in the same tenant, i know how to do it for Inter Tenant but i cannot get it working when inside the same tenant with two different VRFs using different BD. any ideas thanks

3-arm design on ASAv Possible?

Would like to know if we can create a 3-arm design on the ASAv? Possible?

ACI shared L3 out connection via tenant Common

For L3 connectivity outside the fabric, I config L3-out in tenant Common, I want to share L3 connection for multi tenants. How to do this.Please help me!Thanks.

Resolved! Cisco Nexus 9500 Spine Config

Hi We are planning a leaf and spine architecture using Nexus 9300 & 9500 in NX-OS mode.Seek to know if an overlay(VXLAN) is mandatory in leaf and spine modeAlso whats the configuration that s required on the Nexus 9500 Spine (routing?)Can I actually ...

Resolved! Cisco APIC and APIC-EM

Hi, I have some questions below in preparation for our upcoming implementation. 1. APIC-EMa. Is the Nexus 9K required to use APIC-EM?b. What are the components to use this?c. What are the supported Catalyst switches/IOS versions to u...

Recommended Stable Version for Nexus 9500/9300

Hi,What is the recommended stable version for the Nexus 9500/9300 DC Switches?

Layer2 OUT vs Extending static EPGs

Hello - I am working on migrating an exiting DC to an ACI fabric. Initially, we will be mapping EPGs to the legacy VLAN tags as most of my existing connections are all just plain dotq trunks between my existing switch infrastructure (Cisco 6500s and...