Hi Experts , How do I check the PSU status of LEAF switch from GUI and also from CLI .
Forum Posts
Resolved! Moving a Subnet Between Bridge Domains
Hello everybody, I ran into a problem when trying to delete a subnet from a BD and create the same one on a different BD.Let me explain the whole use-case, we work with ACI in a Network Centric manner, this means that VLAN=epg/bd.We created an epg an...
how to Add ACI copy service to existing l4-7 PBR serivce-graph ? and will that cause a traffic disruption ? We have PBR l4-7 pbr service graph deployed to a one-armed firewll that is filtering all traffic with any/any contract. No we want to copy the...
Resolved! OSPF on ACI
If I remember correctly, when configuring OSPF L3Out in ACI, the default Area# and Area type are 1 and NSSA respectively. Majority of the cases I ran into is ACI fabric would be running as the CORE in DC. So I would have to change them to 0 and stand...
Hello team, I have 2 questions (confusion) regarding ACI Fabric discovery:1- When the Leaf-1 sends a DHCP Discover, the offered IP is assigned to the Infra interface VLAN, right? (and then the Lo0 interface is configured from the bootstrap file)?(I m...
C9500-48Y4C - 17.3.4 (L3-out connected to ACI) Cisco ACI 4.2(7l) Controller | n9000-14.2(7l) (No change made on ACI)on Cat 9500 command enteredip pim bidir-enableno ip multicast-routingip multicast-routingLeaf Switches were crashed: any idea (switch ...
Hello Community, I have a question about TCPdump on a leaf Switch (ACI). When I start a TCPdump for an IP address learned via an L3OUT on the Border Leaf, see the ping in the TCPdump. When I start a TCPdump for an IP address learned as EPG -> BD, I...
In attached scenario leaf 103 continues to forward multicast to spine 202 over another ftag tree where spine 202 is the root.Could someone explain whats the need to do so as spine 201 would have already sent multicast frame to all leaf switches.Also ...
We are migrating some Dell Chassis to our ACI infrastructure with B22 expansion modules. The FEX's are online but I do have a question about the speed settings in the Leaf Access Policy Group, should this be set to 10GBs or 1GBs? The infra team is ...
Hello Cisco, I'm trying to configure in-band management on the ACI fabric, but the APIC in-band management IP address is not being advertised into the in-band management VRF routing table. The Leafs can ping each other in the in-band management VRF b...
Hi Folks,Is there a way, via moquery perhaps, to filter where a certain filter is used and in which contract?I have looked around and played with moquery but it doesnt seem to give me the needed results.Thanks!
Hi,I have a SIP Trunk Server (Debian - Kamailio) - in EPG1/BD1, and a Media Server in EPG2/BD2 - communication is SIP --> Media :UDP:5060 - I have a Contract to allow UDP:5060 (and a few more voip specific ports and i also allowed icmp) - the call ...
hi all, I'm trying to understand whether it's possible to enable LLDP or CDP on the fabric interfaces, i.e. the interfaces that connect the leaves to the spine. I'm trying to use a Solarwinds Orion Maps and it doesn't detect the connection perspectiv...
Good day.From time to time I need to verify whether a specific port is being opened or not, so I would like use Postman to query a defined ACI Filter but the problem I have is that the Postman response does not have the port information, and I do not...
Hi all,is it possible and recommended to connect a active/passive firewall (Cisco Firepower) with a L3Out to Cisco ACI without SVI? Instead of SVI we want to use routed port because we need multicast support on this L3Out. Multicast over SVI is not s...
