02-17-2017 11:28 AM - edited 03-01-2019 05:09 AM
I have a new ACI just turned on and attached to the core switch. The goal is migrating servers from core to ACI one VLAN at a time.
BD_1504 and EPG_1504 were created for all hosts in VLAN 1504. SVI for 1504 is at the core switch. I think the link and VLAN are correct because I can see clients in VLAN 1504 are populating in the EPG_1504 Operational.
Two physical servers connect to port 13 on two FEXs which connect to two LEAVE. These severs have not been able to communicate. They can’t even communicate with each other. I have tried with Trunk and Access 802.1P in Mode
Fex Profile Interface Policy Group GENERIC associates to AEP with Physical Domain that include all VLANs in Production
Any helps, suggestions is appreciated. Apology if this question has been answered.
Regards,
Solved! Go to Solution.
02-20-2017 04:09 AM
how did you configure the static binding? if you want access port, please try either 802.1p (recommended) or access(untagged)
thanks for the output. one more command...
-show interface e111/1/13
by the looks of it, they are virtual machines (mac 0050), if they are windows, can you confirm the firewall is disabled for both?
02-18-2017 05:49 AM
Hello
Thanks for using SupportForums
To get started, please provide the following output from the leaf
-show fex detail
-show fex
-show vlan ex
-show endpoint
Im not sure i understood but you have a FEX connected to two leafs? or the endpoint is connected to two FEX on two different leafs?
02-19-2017 06:00 AM
Dpita,
Thank you for your help.
These are two hosts connect to two FEXs. We can focus on one host on leaf111-fex111-port13. These are the show commands that you request, I hope I did not omit any crucial details.
L111# show fex detail
FEX: 111 Description: FEX0111 state: Online
FEX version: 12.1(1h) [Switch version: 12.1(1h)]
FEX Interim version: 12.1(1h)
Switch Interim version: 12.1(1h)
Extender Model: N2K-C2248TP-E-1GE, Extender Serial: FOX
Part No: 68-4059-03
Card Id: 149, Mac Addr: 00:00:00:00:00, Num Macs: 64
Module Sw Gen: 22 [Switch Sw Gen: 21]
pinning-mode: static Max-links: 1
Fabric port for control traffic: Eth1/45
Fabric interface state:
Eth1/45 - Interface Up. State: Active
Eth1/46 - Interface Up. State: Active
Po6 - Interface Up. State: Active
Fex Port State Fabric Port
Eth111/1/1 Down Po6
Eth111/1/2 Down Po6
Eth111/1/3 Down Po6
Eth111/1/4 Down Po6
Eth111/1/5 Down Po6
Eth111/1/6 Down Po6
Eth111/1/7 Down Po6
Eth111/1/8 Down Po6
Eth111/1/9 Down Po6
Eth111/1/10 Down Po6
Eth111/1/11 Down Po6
Eth111/1/12 Down Po6
Eth111/1/13 Up Po6 <SERVER is on this port>
L111# show fex
FEX FEX FEX FEX
Number Description State Model Serial
--------------------------------------------------------------------------
111 FEX0111 Online N2K-C2248TP-E-1GE FOX
121 FEX0121 Online N2K-C2248TP-E-1GE FOX
L111# show vlan ex
5 Production:AP-Prod:VLAN1504 active Eth1/3, Eth1/4, Eth111/1/13,Po4
26 Production:BD-VLAN1504 active Eth1/3, Eth1/4, Eth111/1/13,Po4
L111# show endpoint | include vlan-1504
<output omit, more endpoints on this Vlan also omit>
5/Production:Production vlan-1504 0050.xxxx.xxxx LV
Regards,
02-19-2017 07:07 AM
This is the show interface where the server connect to. Note that the Port mode is TRUNK. How can I make this trunk port with native VLAN 1504? I think that is my problem.
L112# show interface Eth112/1/13
Ethernet112/1/13 is up
admin state is up, Dedicated Interface
Hardware: 100/1000/auto Ethernet, address: 042a.e211.5a4e (bia 042a.e211.5a4e)
MTU 9000 bytes, BW 1000000 Kbit, DLY 1 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, medium is broadcast
Port mode is trunk
full-duplex, 1000 Mb/s
FEC (forward-error-correction) : disable-fec
02-20-2017 04:09 AM
how did you configure the static binding? if you want access port, please try either 802.1p (recommended) or access(untagged)
thanks for the output. one more command...
-show interface e111/1/13
by the looks of it, they are virtual machines (mac 0050), if they are windows, can you confirm the firewall is disabled for both?
02-20-2017 06:55 AM
dpita,
That is, change the binding to 802.1p works. While in EPG not allow mixing trunk with access binding, it does allow trunk and 802.1p.
Best Regards.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide