cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
830
Views
0
Helpful
0
Replies

N9K-C9372PX-E - autoboot or failed autoboot falling to loader

fasnettec
Level 1
Level 1

i got this device from my friend and it not booting so im trying to boot it from tftp and install nxos on it but i got this error and this is my device log : 

CISCO SWITCH Ver7.17

Device detected on 0:6:0 after 0 msecs

Device detected on 0:1:1 after 0 msecs

Device detected on 0:1:0 after 0 msecs

MCFrequency 1600Mhz

Relocated to memory

Detected CISCO IOFPGA

Donner Present

MIFPGA Present

Code Signing Results:                                    0x0

Using Upgrade FPGA

Booting from Primary Bios

FPGA Revison        : 0x6

FPGA ID             : 0x1345727

FPGA Date           : 0x20141015

Power Debug Register: 0x0

Reset Cause Register: 0x80000000

Boot Ctrl Register  : 0xe0ff

FPGA Update Status  : 0x20

Detected CISCO MIFPGA

Version 2.16.1240. Copyright (C) 2013 American Megatrends, Inc.

Board type  2

IOFPGA @ 0xc8000000

SLOT_ID @ 0xf

Trying to read config file /boot/grub/menu.lst.local from (hd0,4)

 Filesystem type is ext2fs, partition type 0x83

Trying to read config file /boot/grub/menu.lst.local from (hd0,5)

 Filesystem type is ext2fs, partition type 0x83

No autoboot or failed autoboot. falling to loader

 

 

 

                Loader Version 7.17

 

loader > set ip 192.168.100.121 255.255.255.0

Correct - ip addr is 192.168.100.121, mask is 255.255.255.0

Finding driver for NIC vendor 8086 Device 438

Found the device 8086:438 at ioaddr e000, membase d8200000 at 1:2

Probing...igb: e1000_set_media_typeMedia type is copper 00900c00

igb: e1000_set_media_typeMedia type is copper 00900c00

igb: INTEL MAC+PHY reset (ctrl 0x08d00240)

igb: INTEL p has large-format EERD

igb: INTEL has EEPROM MAC address

Ethernet addr: E0:0E:DA:2A:0C:D6

igb: INTEL link status is 0x80080747

Link is up

Link speed = 100 Mbps, Full Duplex

igb: e1000_init_rx_addrsigb: Programming MAC Address into RAR[0]

igb: Clearing RAR[1-15]

Tx: TDBAL: 0x7d739d80

TDLEN: 128

TCTL: 0x0003f0fa

TXDCTL: 0x02000000

TDH: 0x00000000

TDT: 0x00000000

 tx_head=0x00000000, tx_tail = 0x00000000

Rx: RDBAL: 0x7d739c80

RDLEN: 128

RCTL:  0x04008002

RXDCTL:  0x02010a0c

RDH:  0x00000000

RXCSUM:  0x00000300

RDT:  0x00000007

igb: INTEL link status is 0x80080747

Link is up

Link speed = 100 Mbps, Full Duplex

CTRL: 0x08d00240

STATUS: 0x80080747

CTRL_EXT: 0x12900c00

TXCW: 0x00000000

RXCW: 0x00000000

TPR: 0x00000006

TPT: 0x00000000

EECD: 0x00004718

EERD: 0xd60c020a

FCAL: 0x00c28001

FCAH: 0x00000100

FCT: 0x00008808

VET: 0x81008100

FCTTV: 0x00000000

LEDCTL: 0xcf06cf02

PBA: 0x00000000

ICR: 0x00000004

ITR: 0x00000000

ICS: 0x00000000

IMS: 0x00000000

IMC: 0x00000000

RCTL: 0x04008002

FCRTL: 0x00000000

FCRTH: 0x00000000

RDBAL: 0x7d739c80

RDBAH: 0x00000000

RDLEN: 0x00000080

RDH: 0x00000000

RDT: 0x00000007

RDTR: 0x00000000

RADV: 0x00000000

RSRPD: 0x00000000

TCTL: 0x0003f0fa

TIPG: 0x00601008

TDBAL: 0x7d739d80

TDBAH: 0x00000000

TDLEN: 0x00000080

TDH: 0x00000000

TDT: 0x00000000

TIDV: 0x00000000

TXDMAC: 0x00000000

TXDCTL: 0x02000000

TADV: 0x00000000

TSPMT: 0x00000000

RXDCTL: 0x02010a0c

RXCSUM: 0x00000300

CONNSW: 0x00000600

PCS_CFG0: 0x00000008

PCS_LCTL: 0x0211000c

PCS_LSTS: 0x0063001b

PCS_ANADV: 0x000001a0

PCS_LPAB: 0x0000d400

Address: 192.168.100.121

Netmask: 255.255.255.0

Server: 0.0.0.0

Gateway: 0.0.0.0

 

loader > set gw 192.168.100.3

Correct gateway addr 192.168.100.3

Address: 192.168.100.121

Netmask: 255.255.255.0

Server: 0.0.0.0

Gateway: 192.168.100.3

loader > cmdline recoery=1

 

loader > boot tftp://192.168.100.3/nxos.9.3.7a.bin

Booting tftp://192.168.100.3/nxos.9.3.7a.bin

Trying netboot

Filename: /nxos.9.3.7a.bin

Address: 192.168.100.121

Netmask: 255.255.255.0

Server: 192.168.100.3

Gateway: 192.168.100.3

 Filesystem type is tftp, using whole disk

..........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................Image valid

 

 

Image Signature verification was Successful.

 

 

image length: 512779264 bytes

Installing klm_card_index

done

Linking n9k flash devices

creating flash devices BOOT_DEV= sda

INIT: version 2.88 booting

Installing ata_piix module ... done.

Unsquashing rootfs ...

Total size needed in bootflash is 108800

check bootflash : OK

Total size needed in bootflash is 41192

check bootflash : OK

Enabling 8250 serial driver spurious INTs workaround

Installing isan procfs ... done.

is_lxc: is_titan_eor: is_stby: suffix: klm_ftrace: /isanboot/lib/modules/klm_ftrace.o

Installing ftrace in non-lxc mode done

Installing SSE module with card index 21025 ... done.

Creating SSE device node 247 ... done.

Loading I2C driver ... done.

Loading MEM scrub driver ... done.

Installing CCTRL driver for card_type 19 without NEED_GEM ... done.

Loading IGB driver ... done.

Not Micron SSD...

 

Checking all filesystems.Warning: switch is starting up with default configuration

 

 **Warning** :Free memory available in /var/sysmgr/ftp is 2048 MB

need atleast 2GB space for RPM extraction via tftp/pxe boot ,run df -h

Installing SPROM driver ... 21025 IS_N9K done.

Installing pfmsvcs module ...done.

Installing nvram module ... done.

Installing if_index module with port mode 6 ... done.

Installing fcfwd

Installing RNI lcnd ... done

Installing LC netdev ... done

Installing psdev module ... done.

Installing veobc module ... done.

Checking SR card

Card Index is 21025

Inserting eMMC module ...

Inserting mtdphysmap module...Inserting OBFL module ... done.

Making OBFL character devices

mounting plog for N9k!

Mounting OBFL pstore for mtd

Inserting kernel_services module ... done.

Making kernel_services character devices

cgroups initialized

exit code: 1

tune2fs 1.42.9 (28-Dec-2013)

Setting reserved blocks percentage to 0% (0 blocks)

Starting portmap daemon...

creating NFS state directory: done

starting 8 nfsd kernel threads: done

starting mountd: done

starting statd: done

 setup_ipv4_mgmt_int_cmos_or_dhcp

Cmos IP=192.168.100.121

Cmos gw=192.168.100.3

Cmos mask=255.255.255.0

Valid IP4 address 192.168.100.121

Valid IP4 gateway 192.168.100.3

eth1      Link encap:Ethernet  HWaddr e0:0e:da:2a:0c:d6

          inet addr:192.168.100.121  Bcast:192.168.100.255  Mask:255.255.255.0

          UP BROADCAST MULTICAST  MTU:1500  Metric:1

          RX packets:0 errors:0 dropped:0 overruns:0 frame:0

          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000

          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

 

 Sleeping for 120 seconds as management interface takes time to come up

eth1      Link encap:Ethernet  HWaddr e0:0e:da:2a:0c:d6

          inet addr:192.168.100.121  Bcast:192.168.100.255  Mask:255.255.255.0

          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

          RX packets:0 errors:0 dropped:0 overruns:0 frame:0

          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:1000

          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

 

Saving image for img-sync ...

 Low free space ,tftp download destination changed to bootflash

 Enough free disk space found on bootflash

mv: missing destination file operand after '/bootflash/nxos.9.3.7a.bin'

Try 'mv --help' for more information.

 not found. TFTP download failed, Pls diagnose your network problem first

Extracting rpms from image...

ls: cannot access /rpms/crdcfg_rpms/t2_tor_crdcfgdata-*.rpm: No such file or directory

ls: cannot access /wrl/: No such file or directory

Card index is 21025

Calling install_tor for TOR

ls: cannot access /rpms/tor_rpms/tor_n9k-*rpm: No such file or directory

ls: cannot access /rpms/tor_rpms/tor_n3k-*rpm: No such file or directory

ls: cannot access /rpms/tor_rpms/tor_n3500-*rpm: No such file or directory

ls: cannot access /rpms/tor_rpms/tor_fretta-*rpm: No such file or directory

ls: cannot access /rpms/tahusd_n9000-*rpm: No such file or directory

mkdir: cannot create directory '/lc': File exists

mount: special device /isanboot/bin/images/ins_tor_n9k.bin does not exist

Not Micron SSD...

Not Micron SSD...

Loading system software

Installing local RPMS

Patch Repository Setup completed successfully

Creating /dev/mcelog

Starting mcelog daemon

INIT: Entering runlevel: 3

Running S93thirdparty-script...

 

Populating conf files for hybrid sysmgr ...

Starting hybrid sysmgr ...

done

Netbroker support IS present in the kernel.

done

Skipping EMON in TOR ...

Executing Prune clis.

ethernet switching mode Wed May  9 23:16:48 UTC 2012

May  9 23:16:49 sysmgr: <<%SYSMGR-2-PARSEERR_INVALIDDEPEND>> /isan/etc/sysmgr.d.hybrid_lc/synctask4.conf:211 [from /isan/etc/sysmgr.conf.hybrid_lc:62] (in dependency list of service "lcdc3_syncpoint4"): service "xbar_client" not defined for scope "control".

May  9 23:16:49 %SYSMGR-2-PARSEERR_INVALIDDEPEND /isan/etc/sysmgr.d.hybrid_lc/synctask4.conf:211 [from /isan/etc/sysmgr.conf.hybrid_lc:62] (in dependency list of service "lcdc3_syncpoint4"): service "xbar_client" not defined for scope "control".

May  9 23:16:50 %FW_APP-2-FIRMWARE_IMAGE_LOAD_SUCCESS No Firmware needed for Non SR card.

2012 May  9 23:16:54  %$ VDC-1 %$  %USER-2-SYSTEM_MSG: <<%USBHSD-2-MOUNT>> logflash: online  - usbhsd

2012 May  9 23:16:56  %$ VDC-1 %$ %CRDCFG-SLOT1-2-CRDCFG_SRV_CRIT: Error getting crd info:

2012 May  9 23:16:57  %$ VDC-1 %$ %CARDCLIENT-2-CARDCL_CRIT: cardcl_af_sync1_done: Failed to get card info

2012 May  9 23:16:57  %$ VDC-1 %$ %MODULE-2-MOD_DIAG_FAIL: Module 1 (Serial number: ) reported failure due to Card Configuration Request Failed in device DEV_LINECARD (device error 0x0)

2012 May  9 23:16:57  %$ VDC-1 %$ %USER-1-SYSTEM_MSG: ASSERT@../utils/usd/libusd/usd_drv.c:3226  - dc3_sensor

[▒

CISCO SWITCH Ver7.17

Device detected on 0:6:0 after 0 msecs

Device detected on 0:1:1 after 0 msecs

Device detected on 0:1:0 after 0 msecs

MCFrequency 1600Mhz

Relocated to memory

Detected CISCO IOFPGA

Donner Present

MIFPGA Present

Code Signing Results:                                    0x0

Using Upgrade FPGA

Booting from Primary Bios

FPGA Revison        : 0x6

FPGA ID             : 0x1345727

FPGA Date           : 0x20141015

Power Debug Register: 0x0

Reset Cause Register: 0x4

Boot Ctrl Register  : 0xe0ff

FPGA Update Status  : 0x20

Detected CISCO MIFPGA

Version 2.16.1240. Copyright (C) 2013 American Megatrends, Inc.

Board type  2

IOFPGA @ 0xc8000000

SLOT_ID @ 0xf

Trying to read config file /boot/grub/menu.lst.local from (hd0,4)

 Filesystem type is ext2fs, partition type 0x83

Trying to read config file /boot/grub/menu.lst.local from (hd0,5)

 Filesystem type is ext2fs, partition type 0x83

No autoboot or failed autoboot. falling to loader

 

 

 

                Loader Version 7.17

 

loader >

 

0 Replies 0
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Save 25% on Day-2 Operations Add-On License