Hello, I have ACI version 5.2 with the following scenario: 2 Tenants for Prod and Dev plus the common tenant for the shared services and the L3OUT, and I want to add L4L7 FW and configure service graphs with PBR to redirect the traffic to the FW. The...
Forum Posts
Resolved! Change OOB IPs of APICs
I have a production fabric (running v4.2(3l) ) and I need to move the OOB management interfaces for the APIC cluster to a different subnet. This looks like it should be an easy enough procedure by updating static node management address for each API...
I tried using aci simulator.However, this virtual switch is automatically registered in the simulator.In the simulator, only a specified node can be registered.This is not what I want.What I want is to simulate multiple switches and register FW , ISE...
Hi Team,In my ACI Infra i can see the NTP staus and synced but it is not showing Synced Server IP. Parallelly in GUI i can see primary server is not selected for sync. Can some one help me on this.:~> ntpstatsynchronised to unspecified at stratum 6ac...
Resolved! What is command to save config in ACI
FolksNew leaf and spine are added to ACI system plus inital config. but all configuration disappear after reboot. Is there a commnad to save all configuration? all regular save command do not work in the system. Thanks
Hi experts,My ACI Fabric is currently running on an APIC-L2-CLUSTER.I prepare a migration to L3 servers, following the Cisco procedure below:https://www.cisco.com/c/en/us/td/docs/dcn/whitepapers/cisco-apic-m1-m2-m3-migration-guide.pdfOn the topic "So...
Resolved! ACI ping node from spine
Hi,I am trying to ping from a spine switch to either a node or interface on a leaf switch, and despite much googling I'm not having any success and would be grateful for any help.The Leaf switch lists the interface I am trying to ping as upL101-DC# s...
When migrating multiple ACI fabrics to Multi-site, normal procedure is that the MSO imports the tenant configuration from one site and stretch it to other sites. The question is that when all sites have had the same tenant configured individually, ho...
Hi guys,About a month or so I've been facing the event with code E4208077 with a frequency of 1 minute. I could not find it anywhere by the description and the code. Does anyone faced the same and know what it can be related to?Thenk you.Description:...
Hi guys, our customer have a multisite solution between two sites: each site have: three apics, two spines and sixs leafs The ISN network have two nexus switch per site this multisite is a production enviroment and read documents related for macsec, ...
Resolved! ACI show running-config in XML format
Hello all,I thought there was a way to dump the ACI running config in XML format using the show running-config command but I can't figure it out. I know I can do moquery -o xml but I'm not sure if that's the same thing? I thought there was an argumen...
Hi Guys,So i wonder if you guys know of a moquery command that i can use to find all the duplicate subnets in the fabric. This also goes for Overlapping subnets. I am planning for our fabric upgrade and one of the requirements is checking all the sub...
Gents just for ultimate clarity: 1st i upgrade all APICs & then upgrade switches in fabric, right? tnx in advance. my 1st in-prod upgrade :0)
Hi all.In APIC, when the work is finished, it should be 'completed' but it becomes 'teardown' and I am in trouble.I can't finish.How do I resolve this? Thank you in advance.Best regards.
Resolved! Move APIC to new leafs
Hi, Is there any special procedure for moving APIC connection to new leaf switches ? Lets say, curretly APIC --> leaf-A & leaf-Bmove it to APIC --> leaf-C & leaf-D if we simply unplug the cables and re-connect them to new leafs will that work ?
