Not sure how many people actually utilize the ACI Endpoint Update App. I have the v2.6 of the App installed on my APIC (v5.2(4f)) and trying to setup it to work with Cisco FMC (v7.2.5). When I click submit on the adding device page of the ACI Endpoin...
Cisco ACI Simulator 6.0.3d Installation Guide The Cisco ACI (Application Centric Infrastructure) Simulator is a valuable tool for simulating ACI environments before actual implementation. In this guide, we will walk through the installation ...
Why does ACI track loose nodes?Fabric > Inventory > Fabric Membership > Unmanged Fabric NodesWhat is ACI doing with these, that it needs to treate these devices with a level of magnificence greater than any other connected, non-fabric device?weylin
Hi, I have an ACI network that has three L3 Outs over two sites. Site A has two L3Outs that are both learning and advertising routes and another on Site B which is learning routes from the core into the fabric, but I cannot work out why it will not ...
We are considering upgrading our ACI infrastructure from software version 5.2(8g) to 6.0(3e)(F) to allow for enhanced SFP & cable compatibility required for a project. I was wondering if anyone would know when we can expect version 6 to become a 'Cis...
Dear Allplease how can I stop continuse ping from ACI console I try ctrl+c but still pinging and try ctrl+shift+6 still pinging
Hi, So, recently i tried to upgrade an APIC-server-M2 firmware with the recommended HUU iso acoording to the version of ACI software: specificly i tried to upgrade from 2.0(3i) to 4.1(2b) of firmware and ACI 4.2(1j) as specified in the release notes....
On a brand new ACI v5.2(8e) fabric, I found there is this F3588 minor fault about "plugin-Cisco_ApicVision" installation failure, screenshot is attached...I assume this plugin came with the APIC software as I never manually try to install it and this...
Hi,Under "Out-Of-Band EPG - default", we can configure static routes but without nexthop (or gateway).. What is the purpose of this option? And why I couldn't find the route when typing "route -n" on the apic cli?
Hello,For some raisons, we want to add a static route for APIC OOB mgmt. By default, when we type "route -n" command on the apic cli; we find a default route 0.0.0.0/0 GW: y.y.y.254, now we want to add another route like 10.x.x.x/24 GW: y.y.y.253In t...
Question#1: ACI supports configuration of Interface delay and bandwidth for EIGRP but it seems like those settings are per L3Out. Anyway to set delay or bandwidth per Interface for EIGRP? Question#2: What would be the use case(s) of Passive interface...
I have some questionsI tried to implement uSeg and didn't understand behaviourI have EPG APP with enforced behaviuor.I made two uSeg epg and without contracts they couldn't speak each other - it's good. After it I permited RDP session between them th...
Hi Gents, I want to deploy the Floating L3OUT towards NSX-T edge deivce to form BGP peering in my current multiPOD environment.I have eBGP peering from LF101 and 102 in POD1 towards Edge1 & 2 and LF201 & 202 in POD2 towards Edge3 & 4. Problem stateme...
Hello Team, One of our customer recently procured Cisco N9K-C9316D-GX along with Cisco QDD-400-CU3M passive cable. They want to run the 200G speed via QDD-400-CU3M passive cable on Switch. Kindly let us know How customer can run and achieve the said ...
Hi, I try tu understand how uSeg works in the ACI.I have one DB-EPG and APP-EPG, I made a contract to allow traffic to communicate between DB-EPG and APP-EPG, it works.Now I want to select some DB servers in DB-EPG and deny traffic between them, I us...
