Can someone please explain to me what this means and the impact. How can i clean the storage to bring the utilization down.Thanks
Can someone please explain to me what this means and the impact. How can i clean the storage to bring the utilization down.Thanks
Hi folks, just did a clean and fresh install of MSO 2.2.3i ..Was also reading through all the documentation and found two default logins after install:"admin / we1come!" for older releases"admin / We1come2msc!" for newer releases..However I am comple...
Hey Folks, I hope somebody has further insight on my issue here.I am trying to monitor my ACI fabric via SNMP Polling (against the OOB IP addresses).Tried this running earlier 4.2(2f) and now 4.2(3j). What I already did and already works:Under Fabric...
We upgraded ACI from 2.2(2k) to 2.2(4p) and upgraded one group of leaf switches after APIC/spine upgrade.APIC showed those leaf switches were upgraded successfully, but actual leaf switches were not reloaded and not upgraded.Have you seen such a thin...
Hi, I'm looking for some guidance. We have aci in network centric mode, and have began migration of services into aci using a physical and a vmm domain, these vlans are statically configured as we are trunking the vlans into aci while we migrate, how...
Hey folks, hope we're doing well.I got a topology where traffic got redirected to a pair of CheckPoint firewalls using PBR. Since there's only one logical interface for each node connecting to the ACI leafs, I also use them as management interface (t...
Hi , I am migrating a traditional network to ACI. I have a L3 (SVI) in the current Cisco core (10.200.1.0/24). The same network consists of 2 FW gateways as mentioned above in the same network. ie 10.200.1.100/24 and 10.200.1.150/24. I know we ca...
Error Message "cannot create or Open DB /var/run/XXX_ae/S255_RXXX/XX_ae.dbState = OperationalCluster = In ServiceHealth = Fully fit Hello all Can someone point me in the right direction for this error please?
Hello, for remote working I connect via VPN to a customer network ACI Fabric.Access to the APIC works fine via GUI and SSH. Currently we have Version 4.2(4k) running. Access to APIC with SSH:ssh apic#<domain>\\<username>@<IP address> But connecting...
Say I have model 9364C as the spine switches and I have already got 64 leaf switches connected, how can I add more leaf switches to scale out? Do another pod or site?
Hi Guys,I have few contracts configure on production site ACI and like to replicate same on DR site ACi. I found the option to export configuration to the PC. how do I import to ACI? I don't see similar option for import under contract like I see exp...
ello All, We have scenario where Multiple EPGs are configured under same Bridge Domain(BD), would like to understand IP assignment for node ...For eg : BD : bd_shared_service , BD Subnet : 10.10.10.0/24EPG-1 : epg_ss_10EPG-2 : epg_ss_20 We have ...
Hello, we are migrating from legacy network to ACI but one of our migration cases is we have 2 groups of servers , group A and group B group A&B servers share same subnet and gateway group A can talk to each other and GW group B can talk to each othe...
Hey Guys,I'm facing the bug CSCvo45816, where the switch has been up for a long time (607 days in my case). Once our timer (32-bit integer) wraps around, the Hal process will see this as a missed heartbeat and reload the switch. The workaround is ru...
Same Tenent --two EPG in different VRF --Unicast routing enabled, Advertise externally, Shared between VRF PBR inserted for both the EPG Endpoint A Tenant-A:VRF_1:EPG_1Endpoint B Tenant-A:VRF_2:EPG_2Endpoint C Tenant-A:VRF_2:EPG_2 EP A--> B is workin...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
04-17-2024 06:22 AM | ||
04-15-2024 11:25 AM | ||
04-10-2024 01:55 PM | ||
04-08-2024 11:40 AM | ||
04-04-2024 03:57 AM |