Hello, Can we say VXLAN is only used at ACI? or where else it can be used? or we can say without ACI, we do not need VXLAN, so VXLAN is generated only for ACI? thanks
Hello, Can we say VXLAN is only used at ACI? or where else it can be used? or we can say without ACI, we do not need VXLAN, so VXLAN is generated only for ACI? thanks
Hi, just to clarify about the service graph integration because the FW technically have multiple sub-interfaces mapped to each VLANs, can we do a static mapping of those VLANs to the ACI when configuring service graphs? I got confused about the tutor...
Hi,Trying to allow access from a L3out epg in the common tenant, to a service hosted within another tenant and I just cannot get the connectivity to work.I've tried:Standard contract provided from the second tenant - not available within common tenan...
Hello Team,Have a quick question about ACI MultiPod fabric and Firewall design. The goal is to have a cluster of two Firepower 4112s in the first Pod and separate/standalone single Firepower 4112 in the second Pod (I cant afford a split spanned Ethrc...
Hello all,I am adding a 3rd spine ("Spine 3") to our ACI fabric and we are making use of some fiber patch panels that we have in the datacenter. The fiber patch panel has standard fiber "cassettes" which take an MTP fiber connection on the back of th...
When sharing services from the common tenant, and multiple customer tenants use overlapping IP addresses, can ACI do NAT/PAT to work around this? For example, the shared DNS would receive packets from the same source IP from 2 tenants, and not know w...
Gents just for ultimate clarity: 1st i upgrade all APICs & then upgrade switches in fabric, right? tnx in advance. my 1st in-prod upgrade :0)
Hi all.In APIC, when the work is finished, it should be 'completed' but it becomes 'teardown' and I am in trouble.I can't finish.How do I resolve this? Thank you in advance.Best regards.
Hi fellas, we are doing a multi-site deployment with the service-graph re-direct use case to a FW local to each site. {We have 2 x DCs.} ACI Fabric will be the default-gateway for all Vlans/BDs. (Even for secured vlans which were previously behind th...
Hello,i have read from many comments that The simulator allows you to connect external management entities such as ESX servers, vCenters, vShields, bare metal servers, L4-L7 services, AAA systems, and other physical or virtual service appliances.but...
Hi I'm trying to use 93180YC-FX as a remote leaf. It is connected to IPN with 10G SFPs in ports 1/45 and 1/46. These ports are downlink ports by default. I have console access to the switch. Can I convert ports 1/45 and 1/46 to fabric ports using swi...
Hi Folks, I have a use case for Policy Based Routing to perform PBR based on specific Source and Destination IP via L3OUT in ACI. Below mentioned is the scenario. There is an EPG-1 where I have a VM 10.10.10.10 and we have a default route towards Fi...
I am going to be bringing a new data center online next week. We have a cookie cutter data center solution so that most of the configuration stays the same between data centers. One example is that there are three APICs, 2 spines, and however many le...
Hi, Is there any special procedure for moving APIC connection to new leaf switches ? Lets say, curretly APIC --> leaf-A & leaf-Bmove it to APIC --> leaf-C & leaf-D if we simply unplug the cables and re-connect them to new leafs will that work ?
Hi, Really new in ACI environment. I read and watched multiple articles/how-tos and videos about ACI logical design but I am not sure which is the best or applicable for a data center if it has the following: 1. Multisite DC (PDC/DR) 2. Both DC have ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-22-2024 03:41 AM | ||
04-17-2024 06:22 AM | ||
04-08-2024 11:40 AM | ||
04-04-2024 03:57 AM | ||
04-04-2024 02:29 AM |