copy is not a recognized - Page 2

pasa barnett · ‎12-07-2015

I am attempting to convert a Nexus 9396 from ACI to standalone mode. i've followed the some online documentation. The image is in the bootfash:

n9000-dk9.6.1.2.I3.4b.bin. I configure the switch to boot the image. and I get the following error. Is there a step I am missing?

Filesystem type is ext2fs, partition type 0x83
No autoboot or failed autoboot. falling to loader

YanL · ‎04-20-2017

I did, no go. bootflash seems corrupted or failed.

I also tried cmdline init_system clear_conf clear_log

Error:

Boot disk not found, Resetting EUSB bootflash
****BOOT DISK NOT FOUND****

Here's the console capture:

loader > cmdline recoverymode=1

loader > boot usb1:nxos.7.0.3.I4.5.bin
Booting usb1:nxos.7.0.3.I4.5.bin
Trying diskboot
Filesystem type is fat, partition type 0xb
Image valid

Image Signature verification was Successful.

Boot Time: 4/20/2017 12:13:10
Boot disk not found, Resetting EUSB bootflash
****BOOT DISK NOT FOUND****
[   38.385856] [1492690429] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000ff00
[   38.385858] [1492690429]
[   38.521822] [1492690429] Pid: 1, comm: init Not tainted 3.4.91-WR5.0.1.13_standard+ #1
[   38.616323] [1492690429] Call Trace:
[   38.658907] [1492690429] [<ffffffff816ff918>] panic+0x11e/0x240
[   38.730559] [1492690429] [<ffffffff8104e34e>] do_exit+0x42e/0x890
[   38.804288] [1492690429] [<ffffffff8104eb10>] do_group_exit+0x80/0xb0
[   38.882176] [1492690429] [<ffffffff8104eb57>] sys_exit_group+0x17/0x20
[   38.961100] [1492690429] [<ffffffff817126a9>] ia32_do_call+0x13/0x13

CISCO SWITCH Ver7.41
Device detected on 0:6:0 after 0 msecs
Device detected on 0:1:1 after 0 msecs
Device detected on 0:1:0 after 0 msecs
MCFrequency 1333Mhz
Relocated to memory
Time: 4/20/2017 12:14:11
Detected CISCO IOFPGA
Donner Present
MIFPGA Present
Code Signing Results:                                    0x0
Using Upgrade FPGA
Checking and setting PSU fan directions
Booting from Primary Bios
FPGA Revison        : 0x8
FPGA ID             : 0x1345727
FPGA Date           : 0x20160526
Power Debug Register: 0x0
Reset Cause Register: 0x80000004
Boot Ctrl Register : 0xe0ff
FPGA Update Status : 0x20
Detected CISCO MIFPGA
Version 2.16.1240. Copyright (C) 2013 American Megatrends, Inc.
Board type 2
IOFPGA @ 0xc8000000
SLOT_ID @ 0xf
Standalone chassis
check_bootmode: grub: Continue grub
Trying to read config file /boot/grub/menu.lst.local from (hd0,0)
Filesystem type is fat, partition type 0xb
Trying to read config file /boot/grub/menu.lst.local from (hd1,4)
Trying to read config file /boot/grub/menu.lst.local from (hd1,5)
No autoboot or failed autoboot. falling to loader

Loader Version 7.41

loader > dir

usb1::

aci-n9000-dk9.12.2.1o.bin
aci-n9000-dk9.12.2.2e.bin
n9000-epld.7.0.3.I4.5.img
nxos.7.0.3.I4.5.bin

bootflash::

loader >

------------------------------------------------------------------------------------------------------

If I boot the ACI image I get to the bash-4.2# prompt

but I don't know what to do at that prompt and it reboots shortly after.

loader > boot usb1:aci-n9000-dk9.12.2.2e.bin
Booting usb1:aci-n9000-dk9.12.2.2e.bin
Trying diskboot
Filesystem type is fat, partition type 0xb
Image valid

Image Signature verification was Successful.

Boot Time: 4/20/2017 12:17:53
[    0.000000] Reserving ebda at 0x9f000 Len 0x61000
Z▒▒W▒▒j▒ZSk▒Sk▒Sk▒Sk▒ZR▒BSk▒VSk▒▒[    6.493162] sd 5:0:0:0: [sda] No Caching mode page found
[    6.558401] sd 5:0:0:0: [sda] Assuming drive cache: write through
[    6.639676] sd 5:0:0:0: [sda] No Caching mode page found
[    6.703106] sd 5:0:0:0: [sda] Assuming drive cache: write through
[    6.783442] sd 5:0:0:0: [sda] No Caching mode page found
[    6.846874] sd 5:0:0:0: [sda] Assuming drive cache: write through
[   20.166465] ata5.00: failed to set xfermode (err_mask=0x4)
[   35.737653] ata5.00: failed to set xfermode (err_mask=0x4)
[   51.308837] ata5.00: failed to set xfermode (err_mask=0x4)
switching root to tmpfs
INIT: version 2.88 booting
Usage: grep [OPTION]... PATTERN [FILE]...
Try `grep --help' for more information.
Found card_index=21025
*** Running INXOS PE IFC image ***
Executing /etc/rc.d/rcS.d/S10mount-ramfs
Total memory: 16399656
Using new partition sizes as sup memory is 8G
*** Running INXOS PE IFC image ***
Mounting /var
Mounting /etc
Mounting /nxos/tmp
Mounting /var/log
Mounting /var/home
Mounting /var/tmp
Skip /var/sysmgr setup to S26 script HW: 1, IFC: 1
Mounting /nginx
Mounting /dev/shm
Mounting /volatile
Mounting /debug
VDC_PREFIX = vdc_
VDC_PREFIX = vdc_
VDC_PREFIX = vdc_
*** Running INXOS PE IFC image ***
Starting udev
e2fsck 1.42.1 (17-Feb-2012)
/sbin/e2fsck: No such file or directory while trying to open /dev/hd-cfg0
Possibly non-existent device?
e2fsck 1.42.1 (17-Feb-2012)
/sbin/e2fsck: No such file or directory while trying to open /dev/hd-cfg1
Possibly non-existent device?
e2fsck 1.42.1 (17-Feb-2012)
/sbin/e2fsck: No such file or directory while trying to open /dev/hd-pss
Possibly non-existent device?
e2fsck 1.42.1 (17-Feb-2012)
/sbin/e2fsck: No such file or directory while trying to open /dev/hd-bootflash
Possibly non-existent device?
e2fsck 1.42.1 (17-Feb-2012)
/sbin/e2fsck: No such file or directory while trying to open /dev/hd-logflash
Possibly non-existent device?
e2fsck 1.42.1 (17-Feb-2012)
/sbin/e2fsck: No such file or directory while trying to open /dev/hd-recovery
Possibly non-existent device?
e2fsck 1.42.1 (17-Feb-2012)
/sbin/e2fsck: No such file or directory while trying to open /dev/hd-ifc-cfg
Possibly non-existent device?
e2fsck 1.42.1 (17-Feb-2012)
/sbin/e2fsck: No such file or directory while trying to open /dev/hd-ifc-log
Possibly non-existent device?
Early mount of filesystems
mount: special device /dev/hd-bootflash does not exist
mount: mount point /mnt/ifc/cfg does not exist
Starting Bootlog daemon: bootlogd.
Starting mcelog daemon
mount: special device /dev/hd-cfg0 does not exist
*** Running INXOS PE IFC image ***
umount: /mnt/cfg/0: not mounted
*** Running INXOS PE IFC image ***
Total memory: 16399656
Using new partition sizes as sup memory is 8G
Number of vdcs supported = 4
Executing /etc/rc.d/rcS.d/S26check-flash
Enter system maintenance mode? (y/n) [n]: ### For now falling back to system mode always ###

Checking partition structure
ls: cannot access /dev/hd-bootdev: No such file or directory
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Error: /dev: unrecognised disk label
Total disk size (MB)0
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Error: /dev: unrecognised disk label
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Error: /dev: unrecognised disk label
Total free space (MB)0
Total partitions found 0
ERROR: Two few partitions
Unexpected Partitioning structure. Fixing it
WARNING: Reformatting disks
mount: special device /dev/hd-bootflash does not exist
mount: special device /dev/hd-cfg0 does not exist
/bin/cp: cannot stat `/bootflash/golden-insieme-image': No such file or directory
/bin/cp: cannot stat `/bootflash/startup-cfg': No such file or directory
/bin/cp: cannot stat `/bootflash/mysetup.sh': No such file or directory
/bin/cp: cannot stat `/bootflash/isim.conf*': No such file or directory
/bin/cp: cannot stat `/bootflash/aci-n9000-dk9.12.2.2e.bin': No such file or directory
/bin/cp: cannot stat `/mnt/cfg/0/boot/grub/menu.lst.*': No such file or directory
Usage: grep [OPTION]... PATTERN [FILE]...
Try `grep --help' for more information.
Usage: umount -h | -V
umount -a [-d] [-f] [-r] [-n] [-v] [-t vfstypes] [-O opts]
umount [-d] [-f] [-r] [-n] [-v] special | node...
*** Running INXOS PE IFC image ***
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened read-only.
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened read-only.
Error: /dev: unrecognised disk label
security_password="cisco"

/dev/:
Issuing SECURITY_SET_PASS command, password="cisco", user=user, mode=high
SECURITY_SET_PASS: Inappropriate ioctl for device
security_password="cisco"

/dev/:
Issuing SECURITY_ERASE command, password="cisco", user=user
HDIO_DRIVE_CMD(identify) failed: Inappropriate ioctl for device
ERASE_PREPARE: Inappropriate ioctl for device
HDIO_DRIVE_CMD(identify) failed: Inappropriate ioctl for device

/dev/:
HDIO_DRIVE_CMD(identify) failed: Inappropriate ioctl for device
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
/isanboot/sbin/init-system: line 67: [: -gt: unary operator expected
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Error: /dev: unrecognised disk label
mkfs.fat 3.0.22 (2013-07-19)
/dev/1: No such file or directory
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Error: /dev: unrecognised disk label
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Error: /dev: unrecognised disk label
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Error: /dev: unrecognised disk label
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Error: /dev: unrecognised disk label
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Error: /dev: unrecognised disk label
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Error: /dev: unrecognised disk label
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Error: /dev: unrecognised disk label
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Warning: Unable to open /dev read-write (Is a directory). /dev has been opened
read-only.
Error: /dev: unrecognised disk label
mke2fs 1.42.1 (17-Feb-2012)
Could not stat /dev/2 --- No such file or directory

The device apparently does not exist; did you specify it correctly?
mke2fs 1.42.1 (17-Feb-2012)
Could not stat /dev/3 --- No such file or directory

The device apparently does not exist; did you specify it correctly?
mke2fs 1.42.1 (17-Feb-2012)
Could not stat /dev/4 --- No such file or directory

The device apparently does not exist; did you specify it correctly?
mke2fs 1.42.1 (17-Feb-2012)
Could not stat /dev/5 --- No such file or directory

The device apparently does not exist; did you specify it correctly?
mke2fs 1.42.1 (17-Feb-2012)
Could not stat /dev/6 --- No such file or directory

The device apparently does not exist; did you specify it correctly?
mke2fs 1.42.1 (17-Feb-2012)
Could not stat /dev/7 --- No such file or directory

The device apparently does not exist; did you specify it correctly?
mke2fs 1.42.1 (17-Feb-2012)
Could not stat /dev/8 --- No such file or directory

The device apparently does not exist; did you specify it correctly?
mke2fs 1.42.1 (17-Feb-2012)
Could not stat /dev/9 --- No such file or directory

The device apparently does not exist; did you specify it correctly?
Erasing 128 Kibyte @ 60000 -- 100 % complete
Erasing 128 Kibyte @ 20000 -- 100 % complete
Erasing 128 Kibyte @ 20000 -- 100 % complete
Erasing 128 Kibyte @ 60000 -- 100 % complete
Erasing 128 Kibyte @ 60000 -- 100 % complete
Erasing 128 Kibyte @ be0000 -- 100 % complete
Erasing 128 Kibyte @ 31e0000 -- 100 % complete
Remounting file systems
mount: special device /dev/hd-cfg0 does not exist
mount: special device /dev/hd-cfg1 does not exist
mount: special device /dev/hd-pss does not exist
mount: special device /dev/hd-bootflash does not exist
mount: mount point /logflash does not exist
mount: mount point /recovery does not exist
mount: special device /dev/hd-ifc-cfg does not exist
mount: mount point /mnt/ifc/log does not exist
mount: unknown filesystem type 'vfat'
mount: mount point /usb/usb2 does not exist
/bin/mv: cannot stat `/dev/shm/golden-insieme-image': No such file or directory
/bin/mv: cannot stat `/dev/shm/startup-cfg': No such file or directory
/bin/mv: cannot stat `/dev/shm/mysetup.sh': No such file or directory
/bin/mv: cannot stat `/dev/shm/isim.conf*': No such file or directory
/bin/cp: cannot stat `/dev/shm/aci-n9000-dk9.12.2.2e.bin': No such file or directory
/bin/mv: cannot stat `/dev/shm/menu.lst.*': No such file or directory
mount: special device /dev/hd-ifc-cfg does not exist
Checking all filesystems.mount: special device /dev/hd-cfg0 does not exist
mount: special device /dev/hd-cfg1 does not exist
mount: special device /dev/hd-pss does not exist
mount: special device /dev/hd-bootflash does not exist
mount: mount point /logflash does not exist
mount: mount point /recovery does not exist
mount: special device /dev/hd-ifc-cfg does not exist
mount: mount point /mnt/ifc/log does not exist
mount: unknown filesystem type 'vfat'
mount: mount point /usb/usb2 does not exist
Checking cfg0
ls: cannot access /dev/hd-cfg0: No such file or directory
Fsck on /mnt/cfg/0
umount2: Invalid argument
umount: /mnt/cfg/0: not mounted
RPARTITION BAD. EXIT TO REFORMAT AND CONTINUE
bash-4.2#

bash-4.2# [ 559.209458] Uhhuh. NMI received for unknown reason 21 on CPU 0.
[ 559.280176] Do you have a strange power saving mode enabled?
[ 559.347841] Dazed and confused, but trying to continue

bash-4.2#

bash-4.2# cd dev
bash-4.2# ls
aer_inject          ptyc9 ptys7 ptyy5        tty57 ttyef      ttyuc
block               ptyca ptys8 ptyy6        tty58 ttyp0      ttyud
bsg                 ptycb ptys9 ptyy7        tty59 ttyp1      ttyue
bus                 ptycc ptysa ptyy8        tty6   ttyp2      ttyuf
char                ptycd ptysb ptyy9        tty60 ttyp3      ttyv0
cmos                ptyce ptysc ptyya        tty61 ttyp4      ttyv1
console             ptycf ptysd ptyyb        tty62 ttyp5      ttyv2
core                ptyd0 ptyse ptyyc        tty63 ttyp6      ttyv3
cpu                 ptyd1 ptysf ptyyd        tty7   ttyp7      ttyv4
cpu_dma_latency     ptyd2 ptyt0 ptyye        tty8   ttyp8      ttyv5
fd                  ptyd3 ptyt1 ptyyf        tty9   ttyp9      ttyv6
full                ptyd4 ptyt2 ptyz0        ttyS0 ttypa      ttyv7
fuse                ptyd5 ptyt3 ptyz1        ttyS1 ttypb      ttyv8
hd-usb1             ptyd6 ptyt4 ptyz2        ttyS2 ttypc      ttyv9
hd-usbdev1          ptyd7 ptyt5 ptyz3        ttyS3 ttypd      ttyva
initctl             ptyd8 ptyt6 ptyz4        ttya0 ttype      ttyvb
kbootctrl           ptyd9 ptyt7 ptyz5        ttya1 ttypf      ttyvc
kmem                ptyda ptyt8 ptyz6        ttya2 ttyprintk ttyvd
kmsg                ptydb ptyt9 ptyz7        ttya3 ttyq0      ttyve
kvm                 ptydc ptyta ptyz8        ttya4 ttyq1      ttyvf
loop-control        ptydd ptytb ptyz9        ttya5 ttyq2      ttyw0
loop0               ptyde ptytc ptyza        ttya6 ttyq3      ttyw1
loop1               ptydf ptytd ptyzb        ttya7 ttyq4      ttyw2
loop2               ptye0 ptyte ptyzc        ttya8 ttyq5      ttyw3
loop3               ptye1 ptytf ptyzd        ttya9 ttyq6      ttyw4
loop4               ptye2 ptyu0 ptyze        ttyaa ttyq7      ttyw5
loop5               ptye3 ptyu1 ptyzf        ttyab ttyq8      ttyw6
loop6               ptye4 ptyu2 ram          ttyac ttyq9      ttyw7
loop7               ptye5 ptyu3 ram0         ttyad ttyqa      ttyw8
mcelog              ptye6 ptyu4 ram1         ttyae ttyqb      ttyw9
mem                 ptye7 ptyu5 random       ttyaf ttyqc      ttywa
mqueue              ptye8 ptyu6 rtc          ttyb0 ttyqd      ttywb
mtd0                ptye9 ptyu7 rtc0         ttyb1 ttyqe      ttywc
mtd0ro              ptyea ptyu8 sda          ttyb2 ttyqf      ttywd
mtd1                ptyeb ptyu9 sda1         ttyb3 ttyr0      ttywe
mtd1ro              ptyec ptyua shm          ttyb4 ttyr1      ttywf
mtd2                ptyed ptyub stderr       ttyb5 ttyr2      ttyx0
mtd2ro              ptyee ptyuc stdin        ttyb6 ttyr3      ttyx1
mtd3                ptyef ptyud stdout       ttyb7 ttyr4      ttyx2
mtd3ro              ptyp0 ptyue tracedevice ttyb8 ttyr5      ttyx3
mtd4                ptyp1 ptyuf tty          ttyb9 ttyr6      ttyx4
mtd4ro              ptyp2 ptyv0 tty0         ttyba ttyr7      ttyx5
mtd5                ptyp3 ptyv1 tty1         ttybb ttyr8      ttyx6
mtd5ro              ptyp4 ptyv2 tty10        ttybc ttyr9      ttyx7
mtd6                ptyp5 ptyv3 tty11        ttybd ttyra      ttyx8
mtd6ro              ptyp6 ptyv4 tty12        ttybe ttyrb      ttyx9
net                 ptyp7 ptyv5 tty13        ttybf ttyrc      ttyxa
network_latency     ptyp8 ptyv6 tty14        ttyc0 ttyrd      ttyxb
network_throughput ptyp9 ptyv7 tty15        ttyc1 ttyre      ttyxc
null                ptypa ptyv8 tty16        ttyc2 ttyrf      ttyxd
port                ptypb ptyv9 tty17        ttyc3 ttys0      ttyxe
ptmx                ptypc ptyva tty18        ttyc4 ttys1      ttyxf
pts                 ptypd ptyvb tty19        ttyc5 ttys2      ttyy0
ptya0               ptype ptyvc tty2         ttyc6 ttys3      ttyy1
ptya1               ptypf ptyvd tty20        ttyc7 ttys4      ttyy2
ptya2               ptyq0 ptyve tty21        ttyc8 ttys5      ttyy3
ptya3               ptyq1 ptyvf tty22        ttyc9 ttys6      ttyy4
ptya4               ptyq2 ptyw0 tty23        ttyca ttys7      ttyy5
ptya5               ptyq3 ptyw1 tty24        ttycb ttys8      ttyy6
ptya6               ptyq4 ptyw2 tty25        ttycc ttys9      ttyy7
ptya7               ptyq5 ptyw3 tty26        ttycd ttysa      ttyy8
ptya8               ptyq6 ptyw4 tty27        ttyce ttysb      ttyy9
ptya9               ptyq7 ptyw5 tty28        ttycf ttysc      ttyya
ptyaa               ptyq8 ptyw6 tty29        ttyd0 ttysd      ttyyb
ptyab               ptyq9 ptyw7 tty3         ttyd1 ttyse      ttyyc
ptyac               ptyqa ptyw8 tty30        ttyd2 ttysf      ttyyd
ptyad               ptyqb ptyw9 tty31        ttyd3 ttyt0      ttyye
ptyae               ptyqc ptywa tty32        ttyd4 ttyt1      ttyyf
ptyaf               ptyqd ptywb tty33        ttyd5 ttyt2      ttyz0
ptyb0               ptyqe ptywc tty34        ttyd6 ttyt3      ttyz1
ptyb1               ptyqf ptywd tty35        ttyd7 ttyt4      ttyz2
ptyb2               ptyr0 ptywe tty36        ttyd8 ttyt5      ttyz3
ptyb3               ptyr1 ptywf tty37        ttyd9 ttyt6      ttyz4
ptyb4               ptyr2 ptyx0 tty38        ttyda ttyt7      ttyz5
ptyb5               ptyr3 ptyx1 tty39        ttydb ttyt8      ttyz6
ptyb6               ptyr4 ptyx2 tty4         ttydc ttyt9      ttyz7
ptyb7               ptyr5 ptyx3 tty40        ttydd ttyta      ttyz8
ptyb8               ptyr6 ptyx4 tty41        ttyde ttytb      ttyz9
ptyb9               ptyr7 ptyx5 tty42        ttydf ttytc      ttyza
ptyba               ptyr8 ptyx6 tty43        ttye0 ttytd      ttyzb
ptybb               ptyr9 ptyx7 tty44        ttye1 ttyte      ttyzc
ptybc               ptyra ptyx8 tty45        ttye2 ttytf      ttyzd
ptybd               ptyrb ptyx9 tty46        ttye3 ttyu0      ttyze
ptybe               ptyrc ptyxa tty47        ttye4 ttyu1      ttyzf
ptybf               ptyrd ptyxb tty48        ttye5 ttyu2      ubi_ctrl
ptyc0               ptyre ptyxc tty49        ttye6 ttyu3      urandom
ptyc1               ptyrf ptyxd tty5         ttye7 ttyu4      vcs
ptyc2               ptys0 ptyxe tty50        ttye8 ttyu5      vcs1
ptyc3               ptys1 ptyxf tty51        ttye9 ttyu6      vcsa
ptyc4               ptys2 ptyy0 tty52        ttyea ttyu7      vcsa1
ptyc5               ptys3 ptyy1 tty53        ttyeb ttyu8      vga_arbiter
ptyc6               ptys4 ptyy2 tty54        ttyec ttyu9      vhost-net
ptyc7               ptys5 ptyy3 tty55        ttyed ttyua      zero
ptyc8               ptys6 ptyy4 tty56        ttyee ttyub
bash-4.2#

bash-4.2#
CISCO SWITCH Ver7.41
Device detected on 0:6:0 after 0 msecs
Device detected on 0:1:1 after 0 msecs
Device detected on 0:1:0 after 0 msecs
MCFrequency 1333Mhz
Relocated to memory
Time: 4/20/2017 12:31:21
Detected CISCO IOFPGA
Donner Present
MIFPGA Present
Code Signing Results:                                    0x0
Using Upgrade FPGA
Checking and setting PSU fan directions
Booting from Primary Bios
FPGA Revison        : 0x8
FPGA ID             : 0x1345727
FPGA Date           : 0x20160526
Power Debug Register: 0x0
Reset Cause Register: 0x80000004
Boot Ctrl Register : 0xe0ff
FPGA Update Status : 0x20
Detected CISCO MIFPGA
FPGA Update Status : 0x20
Version 2.16.1240. Copyright (C) 2013 American Megatrends, Inc.
Board type 2
IOFPGA @ 0xc8000000
SLOT_ID @ 0xf
Standalone chassis
check_bootmode: grub: Continue grub
Trying to read config file /boot/grub/menu.lst.local from (hd0,0)
Filesystem type is fat, partition type 0xb
Trying to read config file /boot/grub/menu.lst.local from (hd1,4)
Trying to read config file /boot/grub/menu.lst.local from (hd1,5)
No autoboot or failed autoboot. falling to loader

Loader Version 7.41

loader >

Tomas de Leon · ‎12-07-2015

You should be able to recover from the loader prompt with the following steps:

1) Copy Image from USB to bootflash:

Loader > dir usb1:
Loader > copy usb1:<ACI Image Name> bootflash:
Or
Loader > dir usb2:
Loader > copy usb2:<ACI Image Name> bootflash:

2) Clear previous configuration, initialize filesystem:

Loader > cmdline init_system clear_config clear_log

3) Boot new image:

Loader > dir
Loader > boot bootflash://<ACI Image Name>

OR

Boot the Cisco Nexus 9000 Series ACI-Mode image from hosting server. For this method, Use TFTP. Use the command, "boot tftp://<tftpserver_ip>/<path>/<ACI_IMAGE.bin>".

pasa barnett · ‎12-07-2015

copy is not a recognized command from the loader prompt.

pasa barnett · ‎12-07-2015

Hi aleccham,

the switch will not even stop at the kickstart..

Tomas de Leon · ‎12-07-2015

Pasa,

From the loader prompt, list the contents of bootflash. Capture the output and paste the response to the forum.

Loader > dir

Thanks

T.

pasa barnett · ‎12-07-2015

I issued the system_init and now the nx-os image is no longer in the bootflash. and i can only get to the loader prompt.

Tomas de Leon · ‎12-07-2015

Pasa,

From the loader prompt, list the contents of bootflash. Capture the output and paste the response to the forum.

Loader > dir

Thanks

T.