cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
9328
Views
0
Helpful
5
Replies

Nexus 93180YC-EX Switch enable FEX feature issue

Hello:

Right now I am deploying a couple of Nexus 9k, and when I try to enable the fex feature, the system displays the following notice: "FEX config is not supported on Tahoe"   Does anyone has seen this notice before? I am aware that Tahoe is the new ASIC family from Cisco, but what is the issue then?

I am trying to add FEX 2228TP

NX-OS version is 7.0(3)I4(5) 

Thanks

Ricardo

5 Replies 5

Siebe Brouwer
Level 1
Level 1

I have the same issue.

Software: NXOS: version 7.0(3)I4(5)
Hardware: cisco Nexus9000 93180YC-EX chassis
FEX: N2K-C2232TM-E-10G

switch(config)# install feature-set fex
FEX config is not supported on Tahoe
switch(config)#

Did you get this fixed?

Hello Siebe:

I used this version: 7.0(3)I4(2)   (nxos.7.0.3.I4.2.bin) and I was able to enable the fex feature. 

Hope this can help

I have not tried to use 93180 to support FEX yet. Based on my understanding, the new 9300 switches are not capable to support FEX as the latest release of 7.0(3)I4(2)

Supported FEX Modules

Cisco NX-OS Release 7.0(3)I4(2) supports the following FEXes (Fabric extenders) on Cisco Nexus 9332PQ, 9372PX, 9372PX-E, 9396PX, and 9500 Series switches:

       Cisco Nexus 2224TP

       Cisco Nexus 2232PP

       Cisco Nexus 2232TM and 2232TM-E

       Cisco Nexus 2248PQ

       Cisco Nexus 2248TP and 2248TP-E

       Cisco Nexus 2348TQ

       Cisco Nexus 2348UPQ

       Cisco Nexus B22Dell

       Cisco Nexus B22HP

       Cisco Nexus NB22FTS

       Cisco Nexus NB22IBM

Note: Cisco Nexus switches other than Cisco Nexus 9332PQ, 9372PX, 9372PX-E, 9396PX, and 9500 Series switches do not support FEXes (Fabric extenders).

Hello Paul-y.

Finally we were able to fix the issue. I've tried with all the I4 path version without success. But with the version 7.0(3)I5(1) the FEX was added to Nexus 9000 successfully.  With all the images within the I4 path version the status was flapping between  "Image Downloading" and "Connected" but never "Online"

NEXUS9K# sh fex detail
FEX: 101 Description: FEX0101 state: Online
FEX version: 7.0(3)I5(1) [Switch version: 7.0(3)I5(1)]
FEX Interim version: 7.0(3)I5(1)
Switch Interim version: 7.0(3)I5(1)
Extender Model: N2K-C2248TP-1GE, Extender Serial: SS******GY
Part No: 73-12748-05
Card Id: 99, Mac Addr: 68:ef:bd:97:b8:42, Num Macs: 64
Module Sw Gen: 12594 [Switch Sw Gen: 21]
pinning-mode: static Max-links: 1
Fabric port for control traffic: Eth1/3
FCoE Admin: false
FCoE Oper: true
FCoE FEX AA Configured: false
Fabric interface state:
Po101 - Interface Up. State: Active
Eth1/3 - Interface Up. State: Active
Fex Port State Fabric Port
Eth101/1/1 Up Po101
Eth101/1/2 Up Po101
Eth101/1/3 Up Po101

.

.

.

Hope this can help. 

Thank you for your answer

Regards

Ricardo

Great,

The new version of NX-OS fixed it. Thanks for the confirmation.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: