ATAs, Gateways and Accessories

Resolved! Provisioning of RT31P2

I'm looking for information on how to provision the Linsys RT31P2 telephone adapter. It is not mentioned in the spa_provisioning_guide.pdf but it's webpages (and the naming of the parameters) look very similar to the WRT54GS, is the spa_provisioning_...

SPA3102 FXO port problem

Hello,I'm having troubles with incoming calls. These calls are ringing on FXS ports, but I need this calls to connect with the IP PBX "Eolix" (FXO Port). I can call from any phone, the only trouble is that the incomings calls are not connecting with ...

Delay on using outgoing PSTN on SPA 3102

Hi,I have been using a SPA 3102 on Pennytel for about a year with no problems.However, now when I dial out using gw0 (PSTN) I have an interesting problem:The number rings for about 30 seconds (but there is no response at the other end), if I persist ...

SIPURA (LINKSYS) SPA 1001

Can my SIPURA (now LINKSYS) 1001 re-direct calls to my cellphone? My VoiP carrier is USA based but my cell has a Venezuelan carrier. If so what do I have to do to make it work.

Need informations about PAP2 and WRP400 provisionning

Hello,i'm just checking how to pre-provision and auto-provision the PAP2 and WRP400 like i have done with the SPA922.In a fist time i need to know how to modify the configuration file (before encrypting) to put the SIP informations (server, Id, passo...

Getting to admin page on non-provisioned RC-model

Hello!When we were RC-certified, we provided an admin-password with the RC-profile. On a unit with profile: pending, hos do you get to the admin pages? Upon entering /admin you just get a 403 but without being presented with the possibility to specif...

Resolved! PAP2T with CUCM

Hello. Is PAP2T compatible with Cisco Unified Communications Manager? If yes, which versions of CUCM? Are there any restrictions? I suppose it uses 3rd-party SIP DLUs, but how many? Thanks.

SPA8000: attended transfer with FLASH does not work

Hi,I'm having trouble with attended transfers on phones connected to an SPA8000.If an SPA phone A calls another SPA phone B which in turn, picks the call up and subsequently presses the R key (Flash) and dials another SPA extension C until C picks th...

SPA8000 "partial" dialing and 484 ADDRESS INCOMPLETE responses

Hi,I'm using SPA8000 units with Asterisk servers. I would like to know if the SPA8000 supports "early dialing" or "partial dialing" with "484 ADDRESS INCOMPLETE responses".I would like that feature because I don't want the Linksys device to do the di...

User guide/manual access

Where exactly has Cisco hidden links to user guides? Since this move to cisco.com you can't find anything easily. Am I just missing something? If so, I've had several others look for them too but they seem to also miss them. Please return full an...

Resolved! Reboot reasons for SPA2000/2102/PAP2

From time to time when we do troubleshooting on customer equipment we run into log lines that state a "reboot reason", I have been unable to find a document describing what errors these codes (for example c200, c40000 and so on) resolve to. Is there ...

Problems configuring a SPA2102 for FAX - HELP?

I am having trouble configuring a fax line on the Linksys SPA2102. Please can somebody assist with this. I have checked all doc's on the device and no good info found on the fax configs. We are using fax over VOIP.

ATAs, Gateways and Accessories

Forum Posts

Resolved! Provisioning of RT31P2

SPA3102 FXO port problem

Delay on using outgoing PSTN on SPA 3102

SIPURA (LINKSYS) SPA 1001

Need informations about PAP2 and WRP400 provisionning

Getting to admin page on non-provisioned RC-model

Resolved! PAP2T with CUCM

SPA8000: attended transfer with FLASH does not work

SPA8000 "partial" dialing and 484 ADDRESS INCOMPLETE responses

User guide/manual access

Resolved! Reboot reasons for SPA2000/2102/PAP2

Problems configuring a SPA2102 for FAX - HELP?

Hearty congratulations to the December Spotlight Award winners!

Renew.cisco.com just got refreshed, and it will make your life easier!

Announcing Resources That Guide You to Success

SPA122 RC - Pending configuration

SPA112 Web interface hangs randomly, cannot configure network

SPA112 No line feed

SPA122 Web Interface Issue

SPA 3000 Problem