Environment:
SPA232D, latest firmware 1.3.1(003_240)
SPA302D handset, firmware 2.40, registered as DECT 1 line.
User wishing to call 800123456 number.
Our user are usign two styles of dialing. Some users:
[A1] push green button
[A2] then enter called number
While other users:
[B1] enter called number
[B2] then push green button.
Both styles work on SPA5xx and SPA1x2 (well, analog phones connected to SPA1x2) devices, so users wish the exact order doesn't matter.
Unfortunatelly, on the SPA232D+SPA302D the only A style dialing work. With B style dialing the ATA device append '#' to the end of dialed number:
INVITE sip:800123456%23@10.250.250.1:5060 SIP/2.0
The PBX know no how to call 8001234546# so call is rejected. It confuse our users.
It's not welcomed behavior of SPA232D. Is there a way to disable unintentional modification of dialed number ?
Just for the completeness, there is syslog&debug log:
cordless_tick(), got something...
cordless_SIP_AP_eventProc(), recevie cmd = 0, src AP = 2
Initial Address
(instance = 0x1000000e, source = , dest = , line = 2)
Cordless session 0 allocated
cordless_SIP_AP_eventProc(), IAM comes from handset 1
preProcessHandsetOutNum(0x309198)
preProcessHandsetOutNum(2)
cordless_findHsNextCcCall(), hs=0x0x2fb834, mode=1, pLid=0x0x407b7a40, pDid=0x0x407b7a3c
select: DECT line1
found idle call 0
sysstatus_set_led_status_payton(), led_id: 4, statusCode:15, systemEvent: 0x100106
cordless_SendLineCfm(0, 1, 0)
CC_main(), evt 10
CC_main(), lid=3, cid=0, CC_CALL=0x32a91c
callEventProcTable[0] is cepIdleProc
cepIdleProc(line=0x32a918, call=0x32a91c, event=10(CC_EV_USR_SEIZURE), par=0, par2=0x309198)
cepIdleProc(), lid=3
cepIdleProc(), pname=10.250.250.1
cepIdleProc(), SYS_NOREG_CALL(3)=0, SIP_REGISTER_OK(3)=1
NEW_CALL_STATE(), call 0: old state = CC_CST_IDLE, new state CC_CST_DIALING
NEW_CALL_STATE_CORDLESS(0), CC_CST_IDLE ==> CC_CST_DIALING
cordless_findSessByLineIdandCID(3, 0), session[0].nCcLineId=3, session[0].nCcCallId=0
Start timer for Dialtone timeout,dial_tone_length = 65535
cepIdleProc(), sid = 0
Set QoS succeed
Apr 24 15:28:47 SPA232D msgswitchd[339]: D2V_SS7_DataReceived
Apr 24 15:28:47 SPA232D msgswitchd[339]: *** SS7 Message ***
Apr 24 15:28:47 SPA232D msgswitchd[339]: *** SS7 Message *** wInterface [AP_SIP] wCmd [IAM]0 wsource [AP_DECT]
Apr 24 15:28:47 SPA232D msgswitchd[339]: IAM Recv SS7 IAM u32_Instance 0x1000000e SS7 IAM u32_SessionType 0x0 SS7 IAM u32_Line 2 SS7 IAM u32_Handset 1 SS7 IAM pu8_Src [0][0][] SS7 IAM pu8_Dst [0][0][]
Apr 24 15:28:47 SPA232D msgswitchd[339]: Codec1 = 9, Codec2 = 0
Apr 24 15:28:47 SPA232D msgswitchd[339]: printSS7Data done
Apr 24 15:28:47 SPA232D msgswitchd[339]: *** SS7 Message ***
Apr 24 15:28:47 SPA232D msgswitchd[339]: *** SS7 Message *** wInterface [AP_DECT] wCmd [INF]8 wsource [AP_SIP]
Apr 24 15:28:47 SPA232D msgswitchd[339]: ss7_send_msg : Unknown AP Send To DECT ss7 -> nl, dst[AP_DECT], dst 2, len 96
Apr 24 15:28:47 SPA232D msgswitchd[339]: In netlinkSendMessage contenttype 1
cordless_eventProc(107(CC_EV_TO_CO_CALL_SEIZURED), 0, 0, 00000000)
Apr 24 15:28:48 SPA232D msgswitchd[339]: D2V_SS7_DataReceived
Apr 24 15:28:48 SPA232D msgswitchd[339]: *** SS7 Message ***
Apr 24 15:28:48 SPA232D msgswitchd[339]: *** SS7 Message *** wInterface [AP_SIP] wCmd [SAM]1 wsource [AP_DECT]
Apr 24 15:28:48 SPA232D msgswitchd[339]: SAM Recv SS7 SAM u32_Instance 0x1000000e SS7 SAM pu8_Dst 800123456#
Apr 24 15:28:48 SPA232D msgswitchd[339]: printSS7Data done
cordless_tick(), got something...
cordless_SIP_AP_eventProc(), recevie cmd = 1, src AP = 2
========================Instance ID = 1000000e===========================
00
===================================================
===================================================
002fd5ec
===================================================
800123456#
===================================================
Subsequent Address=800123456# line 3
call state(3, 0) = 1
CC_main(), evt 103
CC_main(), lid=3, cid=0, CC_CALL=0x32a91c
callEventProcTable[1] is cepDialingProc
cepDialingProc(line=0x32a918, call=0x32a91c, event=103(CC_EV_FROM_CO_DSTRING_DIALED), par=0, par2=0x3091ac)
cepDialingProc(), event = 103(CC_EV_FROM_CO_DSTRING_DIALED)
cepDialingProc(), dn = (null)
callEventProcTable[1] is cepDialingProc
cepDialingProc(line=0x32a918, call=0x32a91c, event=34(CC_EV_TMR_DIALPLAN), par=0, par2=(nil))
cepDialingProc(), event = 34(CC_EV_TMR_DIALPLAN)
cepDialingProc(), dn = 800123456#
[checkSuppFeatActCode] lid 3 vid 3 dn 800123456#
cepDialingProc(CC_EV_TO_CO_CALL_ADDR_COMPLETED(800123456#))
cordless_SendDialCfm(0, 1, 2)
gwid: -1, lid: 3
getCodecList line 0x32a918 call 0x32a91c clRemote: 0x0 bInbound 0
pconly: 128
====== Local codec num 1 ======
8
================================
NEW_CALL_STATE(), call 0: old state = CC_CST_DIALING, new state CC_CST_CALLING
NEW_CALL_STATE_CORDLESS(0), CC_CST_DIALING ==> CC_CST_CALLING
cordless_findSessByLineIdandCID(3, 0), session[0].nCcLineId=3, session[0].nCcCallId=0
Calling:800123456%23@10.250.250.1:5060, rc=0
++++ called number = 800123456%23
++++ called number = 800123456%23
RTP_nextMediaPort(), port = 16532
RTP_nextMediaPort(), rc=16530
dbg_tmp: initSdp bOneCodec: 0, sdp->ucNumCodec: 2
AUD_allocCallObj() call(0x3af5d0)
[3:0]AUD ALLOC CALL (port=16530)
+++++ initSession AUD_startRtpRx
[AUD]AUD_startRtpRx(0x3af5d0) lid 3
Local loopback mode: None. Type: None.
Remote loopback mode: None. Type None.
DECT call no rtp channel yet, do nothing
[AUD]RTP Rx Up
cordless_tick(), got something...
cordless_SIP_AP_eventProc(), recevie cmd = 9, src AP = 2
CHST (instance = 0x1000000e) =============================
IID 0x1000000e, CH ID 0, CH state 5
Session current call state = 3
send CC_EV_FROM_CO_CHST
cordless_eventProc(108(CC_EV_TO_CO_CALL_ADDR_COMPLETED), 0, 0, 00000000)
CC_main(), evt 104
++++ receive CC_EV_FROM_CO_CHST
+++++ CC_main CHST AUD_startRtpRx
[AUD]AUD_startRtpRx(0x3af5d0) lid 3
Local loopback mode: None. Type: None.
Remote loopback mode: None. Type None.
DECT call CoSess id is 0, rtp_chan is 0
RTP channel setup: udp_no_checksum 0, sysmmetric_rtp 0, tos 0xb8, cos 6, mlb 0.
cordless_start_rtp(), chan:0 remote ip:(null) port:0 local:16530 rx:1 ipt:0 ptime:0
Starting Rx only RTP.
Socket 32 bound to port 16530.
Remote IP/port: 0.0.0.0:0
Codec list from SDP (internal pt):
Codec list from SDP (internal pt):
8
8
136
136[AUD]RTP Tx Down
[AUD]AUD_stopRtpRx(0x3af5d0)
cordless_stop_rtp_rx(), Channel 0.
RTP channel 0 going from Rx to Idle.
RTP configuration:
audio_mode RTP_MODE_INACTIVE, media_loop_level RTP_LOOP_LEVEL_NONE, dtmf2833numEndPakcets 3, opts 0x0
Codec: duration 0, rx_pt_event 101, tx_pt_event -1, tx_pt 0
rx[0] 8 PCMA/8000, rx[1] 112 encaprtp/8000, rx[2] -1
rx[3] -1 , rx[4] -1 , rx[5] -1
Jib: max 180ms, min 60ms, adapt 1
Apr 24 15:28:49 SPA232D msgswitchd[339]: MSGSWD RTCP Reqt len 12 Data 2,35,7312,268435470
Apr 24 15:28:49 SPA232D msgswitchd[339]: In netlinkSendMessage contenttype 2
RTP channel 0 is now Idle.
[AUD]RTP Down
[AUD]AUD_releaseRtp(0x3af5d0)
cordless_stop_rtp(), releasing RTP channel:0
cordless_stop_rtp(), RTP session 0 stopped succussfully
[AUD]RTP channel released
[3:0]AUD Rel Call
SIP_releaseAudioResources(), CC_lineIsIdle(3)=0, gAudLine[3].
Rx payload list:
Rx payload list:
PCMA/8000(8)
PCMA/8000(8)
encaprtp/8000(112)
encaprtp/8000(112)
set RTP_SESSION_OPT_DTMF
RTP configuration:
audio_mode RTP_MODE_REC_ONLY, media_loop_level RTP_LOOP_LEVEL_NONE, dtmf2833numEndPakcets 3, opts 0x0
Codec: duration 0, rx_pt_event 101, tx_pt_event -1, tx_pt 0
rx[0] 8 PCMA/8000, rx[1] 112 encaprtp/8000, rx[2] -1
rx[3] -1 , rx[4] -1 , rx[5] -1
Jib: max 180ms, min 60ms, adapt 1
RTP Channel 0 is virgin: 1.
#### rtp seq number is 311
Apr 24 15:28:49 SPA232D msgswitchd[339]: *** SS7 Message ***
Apr 24 15:28:49 SPA232D msgswitchd[339]: *** SS7 Message *** wInterface [AP_DECT] wCmd [INF]8 wsource [AP_SIP]
Apr 24 15:28:49 SPA232D msgswitchd[339]: ss7_send_msg : Unknown AP Send To DECT ss7 -> nl, dst[AP_DECT], dst 2, len 96
Apr 24 15:28:49 SPA232D msgswitchd[339]: In netlinkSendMessage contenttype 1
Apr 24 15:28:49 SPA232D msgswitchd[339]: D2V_SS7_DataReceived
Apr 24 15:28:49 SPA232D msgswitchd[339]: *** SS7 Message ***
Apr 24 15:28:49 SPA232D msgswitchd[339]: *** SS7 Message *** wInterface [AP_SIP] wCmd [CHST]9 wsource [AP_DECT]
Apr 24 15:28:49 SPA232D msgswitchd[339]: CHST Recv SS7 CHST u32_Instance 0x1000000e SS7 CHST u32_ChannelID 0 SS7 CHST u32_State [SS70_CH_STATE_RESERVE]
Apr 24 15:28:49 SPA232D msgswitchd[339]: printSS7Data done
Apr 24 15:28:49 SPA232D [17194585.036000] In cordless Driver Codec 8 and str PCMA/8000 chan 0
Apr 24 15:28:49 SPA232D [17194585.036000] In cordless Driver Codec 112 and str encaprtp/8000 chan 0
Apr 24 15:28:49 SPA232D [17194585.036000] In cordless Driver Codec 255 and str chan 0
Apr 24 15:28:49 SPA232D [17194585.036000] In cordless Driver Codec 255 and str chan 0
Apr 24 15:28:49 SPA232D [17194585.036000] In cordless Driver Codec 255 and str chan 0
Apr 24 15:28:49 SPA232D [17194585.036000] In cordless Driver Codec 255 and str chan 0
RTP session 0 started
[AUD]RTP Rx Up
SIP_tsInviteClientEventProc(event:27)
SIP_sessTsEventProc(event:27)
xxxx SIP session.c 399730ed-e14ce9c7@10.20.12.247 processInviteResponse statusClass=13
SIP_tsInviteClientEventProc(event:27)
SIP_sessTsEventProc(event:27)
xxxx SIP session.c 399730ed-e14ce9c7@10.20.12.247 processInviteResponse statusClass=1
SIP_tsInviteClientEventProc(event:27)
SIP_sessTsEventProc(event:27)
xxxx SIP session.c 399730ed-e14ce9c7@10.20.12.247 processInviteResponse statusClass=13
SIP_releaseAudioResources() entered ################!!!!!!!!!!!!!!!!!
Requesting call statistics...
RTP TX stats updated for channel 0
RTP RX stats updated for channel 0
Call statistics updated.
AUD_releaseCallObj() call(0x3af5d0)
[AUD]AUD_stopRtpTx(0x3af5d0)
cordless_stop_rtp_tx(), Channel 0.
*** RTP channel not in Tx. Nothing to stop!
[AUD]RTP Tx Down
[AUD]AUD_stopRtpRx(0x3af5d0)
cordless_stop_rtp_rx(), Channel 0.
RTP channel 0 going from Rx to Idle.
RTP configuration:
audio_mode RTP_MODE_INACTIVE, media_loop_level RTP_LOOP_LEVEL_NONE, dtmf2833numEndPakcets 3, opts 0x0
Codec: duration 0, rx_pt_event 101, tx_pt_event -1, tx_pt 0
rx[0] 8 PCMA/8000, rx[1] 112 encaprtp/8000, rx[2] -1
rx[3] -1 , rx[4] -1 , rx[5] -1
Jib: max 180ms, min 60ms, adapt 1
Apr 24 15:28:49 SPA232D msgswitchd[339]: MSGSWD RTCP Reqt len 12 Data 2,35,7312,268435470
Apr 24 15:28:49 SPA232D msgswitchd[339]: In netlinkSendMessage contenttype 2
RTP channel 0 is now Idle.
[AUD]RTP Down
[AUD]AUD_releaseRtp(0x3af5d0)
cordless_stop_rtp(), releasing RTP channel:0
cordless_stop_rtp(), RTP session 0 stopped succussfully
[AUD]RTP channel released
[3:0]AUD Rel Call
SIP_releaseAudioResources(), CC_lineIsIdle(3)=0, gAudLine[3].
