cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Get the latest Cisco news in this February issue of the Cisco Small Business Monthly Newsletter

1021
Views
0
Helpful
7
Replies
Highlighted
Beginner

SPA8000 does not accept certain valid parameters

Hello,

I am pushing my config to my device through http://<device>/admin/resync?tftp://<my-tftp-server>/<config-file>.txt

It is accepting changes fine, with the exception of the following:

<Networking_Service ua="rw" group="Lan_Status/">Bridge</Networking_Service>

<Enable_DHCP_Server ua="rw" group="Lan_Status/LAN_Network_Settings">No</Enable_DHCP_Server>

It keeps reverting these back to these values:

<Networking_Service ua="rw" group="Lan_Status/">NAT</Networking_Service>
<Enable_DHCP_Server ua="rw" group="Lan_Status/LAN_Network_Settings">Yes</Enable_DHCP_Server>

Again, all other changes I apply seem to work fine; so I know the device is accepting my config and trying to apply it..

Thoughts?

Kind Regards,

HondaLove

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
Rising star

SPA8000 does not accept certain valid parameters

You can use the Profile Compiler SPC tool to generate a valid xml configuration example.

You can find it at this link:

http://software.cisco.com/download/release.html?mdfid=282414110&softwareid=282562500&release=6.1.11&relind=AVAILABLE&rellifecycle=&reltype=latest

Regards.

View solution in original post

7 REPLIES 7
Highlighted
Rising star

SPA8000 does not accept certain valid parameters

SPA8000 doesn't support BRIDGE mode.

Regards.

Highlighted
Beginner

SPA8000 does not accept certain valid parameters

It is supported in SPA2102.. These are read-write values, not just read; what are other valid parameters? I have not been able to find documentation on BRIDGE/NAT.

Thanks,

HondaLove

Highlighted
Rising star

SPA8000 does not accept certain valid parameters

You can use the Profile Compiler SPC tool to generate a valid xml configuration example.

You can find it at this link:

http://software.cisco.com/download/release.html?mdfid=282414110&softwareid=282562500&release=6.1.11&relind=AVAILABLE&rellifecycle=&reltype=latest

Regards.

View solution in original post

Highlighted
Beginner

SPA8000 does not accept certain valid parameters

Hey Daniele,

The compiler does not actually generate this value in it's XML config export for some strange reason.

Thanks,

HL

Highlighted
Rising star

Re: SPA8000 does not accept certain valid parameters

Try this, for me works:

C:\Documents and Settings\Desktop>spa8000-6-1-11-spc-win32-i386.exe --sample-xml cfg.xml

  spc: generated SPA8000 sample configuration cfg.xml

I've attached cfg.xml.

Regards.

Highlighted
Beginner

Re: SPA8000 does not accept certain valid parameters

Hey Daniele,

Thanks for generating this. This is the same output that it provided me; howeer, I don't see anything referencing the original XML in question:

Networking_Service
Enable_DHCP_Server

Thanks,

HL

Highlighted
Rising star

Re: SPA8000 does not accept certain valid parameters

These parameters are unchangeable. You can find more info in the ATA admin guide here:

http://www.cisco.com/en/US/docs/voice_ip_comm/csbpvga/ata/administration/guide/ATA_AG_v3_NC-WEB.pdf

See the comparison table at page 12:

RJ-45 Ethernet (LAN) of SPA8000: Maintenance only

See SPA8000 connectivity at page 18:

By default, the device on the AUX port is assigned the network address 192.168.0.0 with a subnet mask of 255.255.255.0. If there is a network address

conflict with a device on the Ethernet port, the network address of the device on the AUX port is automatically changed to 192.168.1.0.

Notes at page 19:

The SPA8000 is not designed to forward IP packets to devices connected to its AUX port and that configuration is not supported.

Regards.