cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
863
Views
15
Helpful
3
Replies

CSCve06744 - N9K vPC peer-keepalive fails after initial mis-config and cannot save config - 1

bandarianusha
Level 1
Level 1

hi, I'm running NXOS: version 7.0(3)I7(4) and still have the issue of saving the configs. The peer-keep is configured correctly with source, destination and VRF.

3 Replies 3

balaji.bandi
Hall of Fame
Hall of Fame

Can you post both the configuration and show vpc from both the switches ?

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Tommy LE BALCH
Level 1
Level 1

Hi still same problem with the 7.0(3)I7(5) on a Nexus9000 C93180YC-FX

 

Log:

2019 May 9 15:39:24.389 N9000 %VPC-2-PEER_KEEP_ALIVE_RECV_FAIL: In domain 10, VPC peer keep-alive receive has failed
2019 May 9 15:39:24.389 N9000 %VPC-2-PEER_KEEP_ALIVE_SEND_FAIL: In domain 10, VPC peer keep-alive send has failed
2019 May 9 15:39:41.697 N9000 %AAA-6-AAA_ACCOUNTING_MESSAGE: update:10.241.21.32@pts/0:lebalch_t:Performing configuration copy.
2019 May 9 15:39:41.789 N9000 %SYSMGR-2-CFGWRITE_ABORTED_CONFELEMENT_RETRIES: Copy R S failed as config-failure retries are ongoing. Type "show nxapi retries" for checking the ongoing retries.
2019 May 9 15:39:41.791 N9000 %SYSMGR-3-CFGWRITE_SRVFAILED: Service "confelem" failed to store its configuration (error-id 0x00000079).
2019 May 9 15:39:42.692 N9000 %SYSMGR-2-CFGWRITE_ABORTED: Configuration copy aborted.
2019 May 9 15:39:43.001 N9000 %SYSMGR-3-CFGWRITE_FAILED: Configuration copy failed (error-id 0x401E0000).

 

Config VPC :

N9000(config)# sh run vpc

vpc domain 10
peer-switch
role priority 10
system-priority 32667
peer-keepalive destination 10.246.19.115 source 10.246.19.114 udp-port 3200 vrf management interval 1000 timeout 5 precedence 6 hold-timeout 3
delay restore 200
no delay peer-link
no dual-active exclude interface-vlan
peer-gateway
no layer3 peer-router
layer3 peer-router syslog interval 3600
graceful consistency-check
auto-recovery reload-delay 240
delay restore interface-vlan 10
delay restore orphan-port 0
no fast-convergence
port-channel limit
no shutdown
ipv6 nd synchronize
ip arp synchronize

 

 

VPC State :

N9000(config)# sh vpc

Legend:
(*) - local vPC is down, forwarding vi
a vPC peer-link

vPC domain id : 10
Peer status : peer adjacency for
med ok
vPC keep-alive status : Suspended (Destina
tion IP not reachable)
Configuration consistency status : success
Per-vlan consistency status : success

Type-2 consistency status : success
vPC role : secondary

Number of vPCs configured : 0
Peer Gateway : Enabled
Dual-active excluded VLANs : -
Graceful Consistency Check : Enabled
Auto-recovery status : Enabled, timer is
off.(timeout = 240s)
Delay-restore status : Timer is off.(time
out = 200s)
Delay-restore SVI status : Timer is off.(time
out = 10s)
Operational Layer3 Peer-router : Disabled

vPC Peer-link status
------------------------------------------------------
---------------
id Port Status Active vlans
-- ---- ------ ----------------------------------
---------------
1 Po1 up 1,3900

You have not posted both the side config.

 

high level :

 

vPC keep-alive status : Suspended (Destina
tion IP not reachable)

 

how is your vpc-peer link connected ? those ports UP ? can you post full config of both please.

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help