When we try to deploy c3650 switch as edge in DNAC it ended up the error as follows:"NCSO20544: Failed to add device L04-IDF04-FE02-TEMP.domain.com to fabric. Only Cisco Catalyst 9000 Series Switches support Layer 2 Pools." DNAC version: 2.2.3.4 swi...
Forum Posts
Resolved! DNA IP Transit using iBGP
Hi, please may you tell me if it is possibile and if it is a supported solution by Cisco to use iBGP session(s) instead of eBGP between Border Nodes and the Fusion router for IP Transit ?Shortly: Fusion Router and Border Router can be in the same BGP...
HmmAdded a CLI credential in Management Credentials and signed it to Global. Bad idea.I want to be able to use it on specific sites. Not Globaly....But in Management Credentials its grayed and cant be deleted just edited AaaaahhAny ideas???
Dear Friends,As shown in the attached picture, I have the SDA network configured.My goal is to remove the distribution switch connected to SITE-A CO1 & CO2 and migrate the Admin building G Floor and Floor-1 edge switches to SITE-B CO1 & CO2.My doubts...
Hi!Im using a remote host to store all my backup data of my dna center, after a reset I did to the dnac I cant see any backups on the backup tab (system->backup and restore->backups).I have daily scheduled backup and everytime it finishes with succes...
We tried to provision a switch through LAN Automation and we receiveid this error: "Perform write-erase and reload on PNP device TSPXXXXXXXXX after resolving device issue. Please delete this device from PNP page to retry PNP onboarding." Switch 9200-...
The DNA server is connected to the smart account and registered. My network devices do not have a direct connection to the Internet. I'm trying to change the SSM connection mode to "smart proxy". In the audit logs, I can see that the changes are bein...
Hi,I have noticed that during Image Update Readiness Check the config register check it is showing the warning for config register values. As below:Please change the Config-register valueExpected: 0x2102,0x102 Actual: 0x142 (will be 0x102 at next rel...
We need to allow guest wifi users access to internal webmail. I can create a loopback easily, and this works for most clients. We are having an issue with android though due to its use of DoT (DNS over TLS). This occurs on port 853 and does not trigg...
Hi, Currently we have a CORP SSID in our network and are hosted on 3rd party Wireless controller, now we have a requirement to extend that SSID to the SD fabric over the LAN. We are using a Wireless over the top so is there a way to extend this vlan/...
Resolved! Port Channels in C9200
Hi All, Is L2/L3 port channel supported in C9200 with Network/DNA essential license? #sh ver | in Smart Licensenetwork-essentials Smart License network-essentialsdna-essentials Subscription Smart License dna-essentialsAlso with this license can I con...
Management bought some Audio Visual devices that support bonjour/mdns and we are expected to make airplay work.In the below setup AP and A/V device may end up connecting to same switches but because of signal overlap, client can remain associated to...
Hello Experts, After installing OVA file of Cisco SPACES on VM, We are not able to login to SPACES cli via VM itself. Is there any known issue related to Cisco SPACES? I came across bug CSCvx02620 but no concrete solution so far. Kindly help to resol...
Hello, In an ongoing project our customer needs to integrate the DNA deployment with 2 separate ISE deployments : one is specific to the guest wireless use case. Is it possible to integrate DNA with two ISE deployments ? If so, how can we configure D...
Hi all!I would like some advice regarding DNA, 9800 WLC's, ISE and NPS.We currently have an HA 9800-CL WLC pair in our data centers controlling AP's across multiple sites in flex-connect mode. All wireless networks are locally switched except a guest...
