cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
255
Views
5
Helpful
2
Replies
Tala_Ali
Beginner

The correct configuration of the Gateway and statics routes

Hello, 

 

I'm facing a big problem with my DNA center 2nd génération appliance. 

 

My Appliance was shiped with pre-configured software 1.3.0.6  and now it'is upgrated to 1.3.1.5. All functions seem to be installed correctelty and no hardware problem. 

 

the only problem that i'm facing ( is the only and big problem) is that the Entreprise port can't reach my Subnets ( internal network : 10.0.0.0/8 For Data, 192.168.10/24 For servers). I DNA Center  network configuration  is as following: 

 

Entp port (ENP94S0F0)

 

                 IP : 192.168.128.240 

                 Netmask : 255.255.255.0 

                 Default-gateway 192.168.128.254

                 DNS  :blank 

 

Mangement Port (eno1):

 

              IP : 10.3.0.240

             Netmask : 255.255.255.0 

            Default gateway IP address : Blank 

            DNS servers : 192.168.10.10 192.168.10.20 192.168.10.63 

           Static routes: 

             192.168.0.0/255.255.0.0/10.3.0.254  

              10.0.0.0/255.0.0.0/10.3.0.254

 

Cluster port ( ENP94S0F1)

 

            IP : 192.168.129.240  

 

          Mask : 255.255.255.0 

 

          Default gateway : Blank 

 

 X Cluster

              

 CIMC Port : Another subnet ( 10.3.2.10/24)

 

My Subnets adress pool for pnp automation will be on 10.0.0.0./8

 

After throublshooting with ping : 

Ping sourced from Subnets 10.0.0.0/8 or 192.168.0.0/16  to Ent port or Cluster port Doesn't replay. 

 

Ping sourced from subnets 172.16.0.0./12  to Enterprise port == Ok, it's replay , Cluster port doesn't replay 

 

I  Relased that the satics routes configured on the Mangement (GUI) port take precedence over the default routes. 

 

My question are : 

 

1- How can i do the correct configuration for default-gateway and for statics routes ( can someone give explication using my config) ?

2 - Cisco say that we can change IPs and statics routes after deployement. Now i'm using sofware 1.3.1.5, Can somesone confirm that, and which Command should we enter ? 

 

Thanks in advance  

 

1 ACCEPTED SOLUTION

Accepted Solutions
ammahend
Contributor

If you know the IP, static route and gateways that you need to change from Cisco the use this command to start the setup wizard 

sudo maglev-config update

 do it on master Node CLI if this is a cluster and preferably over CIMC 

-Rate helpful posts-

View solution in original post

2 REPLIES 2
ammahend
Contributor

If you know the IP, static route and gateways that you need to change from Cisco the use this command to start the setup wizard 

sudo maglev-config update

 do it on master Node CLI if this is a cluster and preferably over CIMC 

-Rate helpful posts-

View solution in original post

Hello,

Thank you ammahned for your reply. I issued the same config:

sud maglev-config update
** Inter wizard config and change the routes :
1- Entreprise with default gateway
2 - GUI with a static route ( access sourced from my management network).