cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2409
Views
15
Helpful
8
Replies

nexsu9000

networkinblood
Level 1
Level 1

Hi ,

 

I m very new to nexsus ...practising on eveng on cisco nx-os 9000 , every time my switch goes to loader mode . 

my query is --

1-- why its going in loader mode ..

2-- how to recover it 

may be my queries are silly but wanna discuss so other friends will get benifites.

thanks in advance

1 Accepted Solution

Accepted Solutions

balaji.bandi
Hall of Fame
Hall of Fame

is this Lab or real environment :

 

1. Once you got nexus device # prompt, issue a dir bootflash:

  - it will show you the images in the flash as example below :

 

switch# dir bootflash:
       757307904    Feb 16 17:17:14 2017  nxos.7.0.3.I7.4.bin

switch# conf t
Enter configuration commands, one per line. End with CNTL/Z.
switch(config)# boot nxos bootflash:nxos.7.0.3.I7.4.bin
end
copy run start

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

View solution in original post

8 Replies 8

ngkin2010
Level 7
Level 7

1. You didn't specify the boot image in the configuration during the 1st time setup. 

You have to specify it as follow  

(config)# boot nxos bootflash:nxos-image-name
(config)# copy run start

After that, you won't going in 'bootloader mode' when reloading the device.

 

2. If you in the 'bootloader mode' use the following command to boot the image.

loader> boot bootflash:nxos-image-name

balaji.bandi
Hall of Fame
Hall of Fame

is this Lab or real environment :

 

1. Once you got nexus device # prompt, issue a dir bootflash:

  - it will show you the images in the flash as example below :

 

switch# dir bootflash:
       757307904    Feb 16 17:17:14 2017  nxos.7.0.3.I7.4.bin

switch# conf t
Enter configuration commands, one per line. End with CNTL/Z.
switch(config)# boot nxos bootflash:nxos.7.0.3.I7.4.bin
end
copy run start

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Thank you so much sir , for a quick revert .. image file was nxos.7.0.3.I7.4.bin . I am going to configure pVC , VDC , VXLAN ,EVPN MPBGP , STP , If I will found any issue or any query I ll definitely trouble you .

Once again thanks

is this virtual ? the VDC not going to work on virtual, so do not waste time, VDC works only Physical Devices.

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Okk ..it's lab only ..thanks for suggestion .. I m new in nex_os . But I
wanna learn much more on ACI spine _leaf architecture, can I implement
same on lab on virtual switches .

You can find good information over Google and Youtube, since you learning, learn step by step can understand as expected.

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

HI , I followed steps  as u mentioned  earlier ..now like this is coming 

System is coming up ... Please wait ...
....System is coming up ... Please wait ...
....System is coming up ... Please wait ...
....System is coming up ... Please wait ...
....System is coming up ... Please wait ...
....System is coming up ... Please wait ...
....System is coming up ... Please wait ...
....System is coming up ... Please wait ...
....System is coming up ... Please wait ...
....System is coming up ... Please wait ...
....System is coming up ... Please wait ...
..bash-4.2#
bash-4.2#
bash-4.2#
bash-4.2#
bash-4.2#

have you completed the task as mentioned above and saved the config? what kind of emulator are you used to this image?

 

what kind of computer resource do you have?

 

 

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: