I'm currently exploring the Hands-on Lab (HOL) feature and am in the process of setting up the lab computers we would access remotely.
Setting up the computers has been relatively straight forward, however I've been running into some issues with the computers constantly going offline??
I was wondering if anyone else is currently using HOL and if you were willing to share any best practices/tips etc. Has anyone else experienced any similiar issues with HOL?
Any feedback would be greatly appreciated!
Message was edited on June 5, 2013: Kelli Glass, Cisco Collaboration Community moderator, added community categories and tags for greater ease in filtering posts (no change to content).
Clearly you are experiencing an issue that requires you contact WebEx customer support.
I know this is a little late, but, make sure your user is not Shutting down the machine. Once it is shut down, you cannot access it again. The user can log off and disconnect from the remote machine, but stress to them not to shut down the machine.
Hope that helps.
No worries... better late than never. I appreciate your feedback!
We've come a long way since my initial post... I've set up several labs since then and we're actively using over 60 HOL pcs. Hands-on Lab has been a very effective feature for us!
Otherwise, we've determined that our issue with the HOL pcs going offline is more of an internal IT issue... firewalls, proxy settings, etc. We've made some progress here as well but still have some work to do to make sure they are all consistently active.
Thanks again for your response!
I know this is an older thread, but has anyone had issues where the lab pc screen is just blank, and nothing seems to change the status, (send cntl+alt+del) reboot, changed the administrator password under WebEx Services. We are new and would love to know about best practices for HOL.
Thank you for participating in the Collaboration Community. I recommend that you also post this issue to the WebEx Support Forum for more information and assistance.
I hope that helps.
Moderator for the Cisco Collaboration Community
How to get access to Hands on Labs section. Any advise??
Mark me a copy to email@example.com
I use it all the time! When your WebEx training center is setup – the lab is part of it. There is a separate URL that will take you to the Lab Admin page. Obviously you will need to have computers that you plan to use with your lab (virtual or otherwise). You load the access anywhere software and you assign the computer to a lab.
I hope this helps.
Hands-On Lab has a few components:
1. First, configure your HOL Machines: From each computer you want to identify as a 'lab computer', launch the HOL Admin tool located at https://yourwebexsite.webex.com/labadmin. Log in and complete the setup. If you are unable to log-in, then your Site Administrator has not given you permission to be an HOL Lab Administrator and s/he needs to change that in WebEx Site Admin. Once logged in, launch the wizard to configure that computer as a lab machine. Re-launch the same admin URL on each machine you want to be accessible via Training Center as an HOL machine. This is your one-time setup process on each lab computer.
2. Once the machines are configured, you can make them available in a live session, or outside of a live session.
To make the machines available in a live session, reserve them during the TC scheduling process on the Training Center/ Schedule Session page. When you launch your live TC session, you'll see all the HOL machine(s) you reserved in a separate panel and you can click to access the machines remotely.
You can also access HOL computers outside of a live WebEx session by reserving them for On-Demand Access from the Hands-On Lab link in the Training Center navigation bar.
We offer a live, instructor-led HOL class, if you find you'd like to take some training.
Hope this helps.
Hi Jeffrey / Moderator,
Is there any way to find out what the firewall and proxy settings are that affect/cause this problem? We are starting to use Hands-on Labs in a big way, but are experiencing the same exact issue as Jeffrey mentioned in this thread.
I tried searching in the Webex support site, but this is the only reference I could find for this issue. Any help or guidance will be much appreciated!
We are also having the same problems with Pcs going offline in the Hands on Lab we are setting up, so any info about the settings would be very useful.