Which version of CME to be installed on ISR4351

[Rene MUGIRANEZA]

Hello;

I want to know which version of CME to be installed on ISR4351 router.

Its IoS:

Cisco IOS Software, ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.5(3)S4b, RELEASE SOFTWARE (fc1)

Find in attachment the full information about "show version"

[Jaime Valencia]

See here

https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/requirements/guide/33matrix.html

[Maren Mahoney]

I hunted around for a while including the compatibility matrix Jaime linked to which does not list your IOS, and including the Cisco Feature Generator which does not list your IOS at all, and Cisco does not seem to have information for that specific IOS version pretty much anywhere...which is really interesting.

The rule of thumb is that the compatibility matrix will show the minimum IOS version required for a specific version of CME to run. Given the linked matrix, I'd guess isr4300-universalk9.03.16.04b.S.155-3.S4b-ext.SPA.bin would give you CME 10.5. But that is an educated guess at best.

If you already have this IOS version installed, you can run the command "show telephony-service" to view the Express version.

HTH

[Rene MUGIRANEZA]

Hello Maren Mahoney;
When I run "show telephony-service", I got the following output.
This confirms that I should use CME 10.5?



RWAO-VOIP-RTR-1#show telephony-service
CONFIG (Version=10.5)
=====================
Version 10.5
Max phoneload sccp version 17
Max dspfarm sccp version 18
Cisco Unified Communications Manager Express
For on-line documentation please see:
http://www.cisco.com/en/US/products/sw/voicesw/ps4625/tsd_products_support_series_home.html

protocol mode default
ip source-address UNKNOWN port 2000
ip qos dscp:
ef (the MS 6 bits, 46, in ToS, 0xB8) for media
cs3 (the MS 6 bits, 24, in ToS, 0x60) for signal
af41 (the MS 6 bits, 34, in ToS, 0x88) for video
default (the MS 6 bits, 0, in ToS, 0x0) for serviceservice directed-pickup
max-ephones 0
max-dn 0
max-conferences 8 gain -6
dspfarm units 0
dspfarm transcode sessions 0
conference software
privacy
no privacy-on-hold
hunt-group report delay 1 hours
hunt-group logout DND
max-redirect 10
cnf-file location: system:
cnf-file option: PER-PHONE-TYPE
network-locale[0] US (This is the default network locale for this box)
network-locale[1] US
network-locale[2] US
network-locale[3] US
network-locale[4] US
user-locale[0] US (This is the default user locale for this box)
user-locale[1] US
user-locale[2] US
user-locale[3] US
user-locale[4] US
srst mode auto-provision is OFF
srst ephone template is 0
srst dn template is 0
srst dn line-mode single
time-format 12
date-format mm-dd-yy
timezone 0 Greenwich Standard Time
no transfer-pattern is configured, transfer is restricted to local SCCP phones only.
keepalive 30 auxiliary 30
timeout interdigit 10
timeout busy 10
timeout ringing 180
timeout transfer-recall 0
timeout ringin-callerid 8
timeout night-service-bell 12
caller-id name-only: enable
web admin system name Admin
web admin customer name Customer
edit DN through Web: disabled.
edit TIME through web: disabled.
background save interval 10 minutes
Log (table parameters):
max-size: 150
retain-timer: 15
transfer-system full-consult
transfer-digit-collect new-call
local directory service: enabled.
Extension-assigner tag-type ephone-tag.

RWAO-VOIP-RTR-1#

[Maren Mahoney · Accepted solution]

Yes, you got it. You will be running 10.5.

If this solves your problem, please mark this problem solved.

Maren

[Rene MUGIRANEZA]

Dear Maren Mahoney;
Thank you for your quick reply,
Kindly share with me the link where I can download CME 10.5, for me I don't find exact link to download it. My manager has all necessary credential to download it.
Thank you once again for your support.

[Maren Mahoney]

If you have the voice licensing enabled, CME code is included in the IOS. No additional software is necessary, unless you want to use the administrative GUI. CME is usually configured via the command line.

Here is a link to the CME Administration Guide, which provides all of the necessary configuration information:

Cisco Unified Communications Manager Express System Administrator Guide

Maren

[Rene MUGIRANEZA]

Hello Maren;
Yes I want to enable GUI for CME 10.5. Do I need to download files for GUI? If yes, kindly support me to provide the link.
Regards;

[Maren Mahoney]

Here you go. I encourage you to become familiar with how to locate software on Cisco Software Download site.

https://software.cisco.com/download/home/286322815/type/282786567/release/10.5

Maren