cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
18693
Views
10
Helpful
4
Comments
vemanyam
Level 1
Level 1

 

 

Introduction

This document covers the Procedure for Dumping CUCM Fresh Install Logs - Virtualization

 

Problem Description

In order to dump install logs on a virtual UC installation, it is necessary to use a virtual serial port on the virtual machine. By default, a serial port is not present when deploying from the Cisco provided OVA. Thus it will often be the case that the first time you hit an installation problem and need to dump the logs, the serial port will not be available. Use this procedure to add a serial port to the virtual machine and dump the logs.

 

Procedure

Follow this procedure to dump install logs to the serial port on the VM.

1. When the VM is powered off, edit settings and add a serial port to the VM.

Note: You cannot add one while the VM is running.

2. You will be required at this time to attach the serial port to a file. Just attach to any temp/junk file, as this file will NOT be used to dump the logs.

3. Power on the VM and start your installation. At boot up, linux will dump some garbage characters (escape sequence characters) into the temp file you attached to the serial port.

4. When you're ready to actually dump the log files, attach a new, empty file to the serial port by editing settings of the VM while the machine is running. You do not have to power down the VM to change the file attached to the serial port.

5. After the file is saved, you can open it using 7-zip (http://www.7-zip.org/download.html)

6. After you have a successful install in the VM, power off the VM, edit settings and remove the serial port from the VM.

Capture1.JPG

Capture2.JPG

Capture3.JPG

Capture4.JPG

Capture5.JPG

Capture6.JPG

Note

Leaving the serial port (or any other unnecessary virtual hardware) can negatively impact performance of the VM. There is no other use of the serial port in a Unified CM VM other than dumping the install logs, so you will not need it again unless you do a fresh install.

Comments
msaeedi
Level 1
Level 1

and to open the file you will need the program 7zip 

BenBen
Level 1
Level 1

Hi,

 

Thanks for this document. At the end of the document it says:

"There is no other use of the serial port in a Unified CM VM other than dumping the install logs, so you will not need it again unless you do a fresh install."

 

Does this indicate that a "direct standard" install do NOT need a serial port? 

Creating this serial port would need to shutdown the VMs which is not a small task. I am performing a "Direct Standard" upgrade so I want to know if I need the serial port or not.

 

Thanks.

 

-Ben

rrendonm
Cisco Employee
Cisco Employee

No longer supported on CUCM 15, 

 

https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/install/15/cucm_b_install-guide-cucm-imp-15/cucm_b_install-guide-cucm-imp-14_chapter_0100.html

 

Steps to Recover Logs using Recovery CD
You should use the Recovery CD to recover the logs to access the diagnostic information. Follow the steps mentioned:

Insert the recovery CD.

Reboot the system.

Once the recovery CD menu comes up, press Alt + F2 to get to the command prompt.

Find the largest partition by performing a "df -h". (/mnt/part6).

Locate the install logs at: /mnt/part6/log/install/ directory.

Collect the logs.

rrendonm
Cisco Employee
Cisco Employee

A better document on how to collect these logs is here:

How to pull the install logs using the Recovery Disk – CRAZY NETWORKING (defaultgateway.org)

 

  • Gain access to command line and find location of install logs
    1. Mount Recovery Disk
    2. Reboot System and boot to Disk
 

 

Press “Alt + F2” to get to the Command Prompt

 

 

Type “df -h” to show the available partitions.  The biggest partition should have the install logs.  In this example, its part6.

 

 

The install logs should be in the following directory /mnt/<your_install_partition>/log/install

 

 

Assign IP and Gateway to machine for network access

Type “ifconfig” to see the available interfaces.  In this case its eth0.  In CUCM/IMP 12.5 the interface may be ens160

 

 

Next type the following to set the IP address on your interface

ifconfig eth0

ifconfig eth0 netmask <netmask>

route add default gw <gateway_address> eth0

 

 

Transfer Files Using SFTP

Change the directory to the path where the install logs are located

ex: cd /mnt/part6/log/install

Next, connect to the SFTP server.  In my example I am using freeFTPd

Type in sftp sftp_username@sftp_ip

After logging in successfully with username/pw, the prompt should change to sftp

 

 

Since we changed the directory to where the install files are located, you should be able to type the following (This should grab all files in the install folder):

 

put *

Now go to your SFTP server and see if the files are downloaded.

To exit SFTP just type “exit”

To get back to the recovery disk prompt press “Alt + F1”

How to Grab the installdb logs

The installdb logs are in a different location.  If the install is failing at the DB compontent, you may want to pull these as well.  The location should be as follows:

  • /mnt/<your_install_partition>/log/taos-log-a/cm/trace/db/sdi

If you cannot find the installdb log then use this command to find the path:

  • find / -name installdb*

Then change the directory to the location of the installdb log and extract it with the sftp server. 

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: