The Spint Brain Recovery condition in Unity Connections is an odd state to find your Unity Connections cluster in, for sure. One thing is certain though, 'something' happened, and this is the result of whatever that 'something' was or is.
When this condition happens, what you'll notice (either from logs or by watching the cluster node status) is that the Primary and HA servers will take turns being the cluster's primary node every few minutes. This is because both cluster nodes have somehow ended up with slightly different database versions and the Server Redundancy Manager service cannot determine exactly which server should be primary. The cluster will try to resolve this issue on it's own, but often times cannot.
The good news (maybe not so good) is that in several cases, the cluster will continue to function and answer calls during a split brain. Where I have seen the split brain condition cause service outage to users is with SCCP integrations that do not have sufficient SCCP ports on both cluster nodes.
What causes this can be a number of things; often it is the result of the two nodes losing network communication between themselves and/or service failure. The resolution to this condition is fairly simple, although, you'd be best served to figure out why it happened in the first place, lest you repeat it again.
Since Unity Connections is running the same operating system as Unified Communications Manager, you can run the same health checks in Unity Connections that you would run you Unified Communications Manager. You'll want to resolve any issues discovered in those health checks before resolving the split brain issue.
Assuming you have a healthy Unity Connections cluster and/or discovered and resolved the issue that caused the split brain you'll want to move on to resolution.
Power off / shut down the true HA node (the node that is not supposed to be the true primary).
In the Cisco Unity Connection Administration section click on Cluster under System Settings in the left-side vertical navigation menu and verify that both nodes are entered in correctly (IP address/hostname/FQDN).
In the Cisco Unity Connection Serviceability section click on Service Management under the Tools menu and verify that the Connection Message Transfer Agent and the Connection Notifer services are started.
Restart the Unity Connections Cluster primary server. From the CLI, issue the command "utils system restart" and press "Y" to the proceeding prompt.
Once the rebooted primary server is back up, wait till you can access the GUI web page of the server before proceeding (in other words, wait till the Cisco Tomcat Service is operational).
From the Unified Communications Server (or other type of call control server), place a call into voicemail (all you really need is something that will signal the IVR to pickup) and then hang-up and wait 5 minutes before proceeding to the last step.
Power on the HA node (that should still be shutdown) and wait till you can access the GUI web page of the server before proceeding (in other words, wait till the Cisco Tomcat Service is operational).
Verify that the split brain status has been removed for the node status on the Cluster Management page under Cisco Unity Connection Serviceability (or issue show cuc cluster status from the CLI of the cluster's primary server).
Run health checks on the cluster one last time, to verify everything is healthy and operational.
The cluster should be back to normal status now and the split brain condition no longer listed on the cluster nodes.
In some instances (usually due to how long the cluster was in this state), even more action is necessary and you may need to reset the cluster replication (done via the CLI of the primary server with, utils dbreplication reset *) if the cluster's database replication is damaged. The need to do this will be discovered in your final set of health checks.
Dear Support,Hope this email find you in good health, We have 96 rooms which has two phones with one EXT Number (for example 101 )and as per my understanding it should take Enhanced plus/ CUWL standard licenses. So it will cover 192 phones as each ro...
Customer would like to know if the below two softwares are compatible with Cisco UCCE 11.6 or 12 contact center solution or not : 1) IBM Security Guardium Ajan for SQL database on Rogger/AW2) HP OpenView Performance Agent / windows with Ag...
Hi, Can some one please explain whats the difference between expressway CE and CUBE, why some one would choose CUBE to deploy inside its CUCM and why someone should choose Expressway to deploye along with CUCM ? Regards,Masood
Looks like iOS 13 Beta 3 breaks the messaging components of Webex Teams. When you select the spaces, the messages don’t load. I know this isn’t a bug or anything to fix, more of an FYI. If anyone does have a fix for this, please let me k...
Hi , Please help me on attached error. When I am trying to update phone book from Manage Phone Book with Manage Phone book source, getting error can not be synced. Also re started the TMS extension services but no luck.