cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
107146
Views
19
Helpful
19
Comments

 

 

Introduction

 

This document answers frequently asked questions about the Cisco Unified Border Element (CUBE).

 

Q1. What are the benefits of using Cisco Unified Border Element ?

 

A:

• Multiple physical interconnects, intelligent OAM, Call Admission Control, Billing etc

• Security Demarc: FireWall, DOS protection, VPN, etc

• Signaling, Protocol & Media Interworking: H.323/SIP, transcoding, DTMF etc.

• Media QoS control and monitoring

• Interoperability: various network elements, CUCM, etc.

• Co-existence/co-operation with TDM trunking

 

 

Q2: What type of Calls are supported in CUBE ?

 

A: CUBE supports,

• IP-to-IP Calls
• TDM Voice Calls
• Gatekeeper
• Routing

 

Q3: How the Media is handled in CUBE ?

 

A: Media is handled in 2 different modes

  • Media Flow-Through
  • Media Flow-Around

 

 

Q4: What Platforms are supported for CUBE?

 

A: Cisco CUBE is an Integrated application with Cisco IOS software.

CUBE functionality is supported in Cisco 2600XM, 2691, Cisco ISR 2800, 3800 series, Cisco VXR 7200, Cisco XR 12000, AS5400XM Universal gateways and the Service Provider Gateways.

 

 

Q5: Do we need Digital signal processors (DSPs) for CUBE?

 

A: Digital Signal Processors (DSPs) are only required for calls with dissimilar codecs

 

 

Q6: What is the licensing requirements of the CUBE?

 

A: If you have any existing Cisco Gateway then you can download the Cisco IOS supported version for running CUBE on your Gateway. Also you need to buy license for the no. of sessions in CUBE for different platform. Say for an example if you want to have a CUBE supporting 500 sessions , you need to buy the license for this amount.

 

Q7: How to have a basic setup between CUCM and CUBE?

 

A: The layout will be CUCM-sip-Cube-sip-provider.

  • First you need to create the SIP trunk on the CUCM and point it to the cube
  • Bind your sip signalling to the appriprate interfaces on the CUBE
  • Enter the respective dial-peers on the cube for inbound and out bound calls to and from the CUCM

 

 

Q8: Do CUCM need special license for CUBE or it will be just a SIP trunk without license?


A: No, there is no special license for connecting CUCM to CUBE..

 

 

Q9: WE have a CUBE for a SIP connection. I know there is a license that we purchased from Cisco. Is there a command to enter on the CUBE to view the licenses?

 

A: The CUBE licenses are not entered into the router. As of now, they are paper licenses.

 

 

Q10: Whether CUBE supports Voice and Data traffic simultaneously?

 

A: Yes. CUBE is in IOS based platform hence it can handle both Voice and Data traffic.

 

Q11: Does CUBE have to be run on a dedicated device/router?

 

A: Not Necessary. It depends on the voice traffic you want to route using CUBE. For large enterprise its recommended to use standalone device for CUBE functionality. If the traffic is not high you can run other services along with the CUBE application for voice on the same platform simultaneously.

 

Q12: Do we need DSP resources in CUBE if the SIP trunk from city (external) to the SIP trunk of CUCM will be used?

 

A: DSP resources are required to simply connect to SIP Trunk. DSP resources are required if you plan on doing transcoding between g711 to g729 codec. For conferences if all parties are using g711 codec, then you can use the software resources in UCM to do the conferencing. If one of the parties is using g729 codec and if that needs to be conferenced, you will need to use voice gateways for hardware conferencing which will require DSPs. Digital Signal Processors (DSPs) are only required for calls with dissimilar codecs.

 

Q13: Will SRST work on CUBE ?


A: Yes, SRST and CUBE can be co-located on the same router.

 

Q14: Explain the Call flow in CUBE.

 

A:

 

callflow cube.bmp

 

1.Incoming VoIP setup message from OGW to CUBE

2.This matches an inbound VoIP dial peer 1 for characteristics such as codec, VAD, DTMF method, protocol etc

3.CUBE then looks up called number in setup and matches outbound VoIP dial peer 2

4.Outgoing VoIP setup message from CUBE to TGW

 

 

Q15: How to enable the IP-IP Calls and Protocol support in CUBE ?

 

A: Enabling the IP-to-IP Calls


CUBE#config t
CUBE(config)# voice service voip
CUBE(conf-voi-serv)#allow-connections h323 to h323
CUBE(conf-voi-serv)#allow-connections h323 to sip
CUBE(conf-voi-serv)#allow-connections sip to h323
CUBE(conf-voi-serv)#allow-connections sip to sip

 

It is mandatory to have Incoming and Outgoing VoIP Dial-peers with required parameters like Protocol, Transport, Codec, CAC, QoS, etc

 

Q16: Whether CUBE supports Universal Transcoding ?

 

A: Yes CUBE supports Universal Transcoding, any to any Voice codec. Example. iLBC to G.711 or iLBC to G.729

 

List of codecs supported

  • g711alaw 64Kbps
  • g711ulaw 64Kbps
  • g723r53 5.3Kbps
  • g723r63 6.3Kbps
  • g723r63 6.3Kbps
  • g729 (all variants) 8Kbps
  • iLBC

 

Q17: What is CAC?

 

A: CAC is Call Admission Control. It control number of calls based on resources and bandwidth and Proactively reserve resources for good quality video calls. Also it ensure traffic adheres to QoS policies within each network. CUBE can provide six different CAC mechanisms

 

Q18: Is CP-PWR-CUBE-4= compatible with the 7900 series phones?

 

A: No this power cube is for the new 8900/9900 phones, compatable with Communications Manager. The power tip is different size, won't fit in other phones.

 

Q19: Im trying to find a way to route inbound SIP calls, based on their source.

 

For example:

 

SIPCarrier1 is coming from 1.1.1.1

SIPCarrier2 is coming from 2.2.2.2

 

If calls originate from SIPCarrier1, I want them to be passed to my UCM Cluster.

 

If call originate from SIPCarrier2, I want them to be passed to my Asterisk box.

 

I've played around with incoming called-number, trying to make it work with IP addresses, rather than phone numbers, but no luck.

 

Any ideas on how to enable source based routing?

 

A: Yes this can be achieved by Carrier based Routing. Refer this link for more details.

 

VoIP Gateway Trunk and Carrier Based Routing Enhancements

 

Q20: CUBE Sizing, how many simultaneous calls/ sessions are supported on each Router model to terminate a SIP Trunk at the service provider end?

 

A: Refer the given table for more details.

 

cube8543_450_238_cache.png

 

cube 8539_450_453_cache.png

 

Q21: What are the types of CUBE licenses available?

 

A:Two types of Cisco Unified Border Element licenses are available:-

 

• Pay-as-You-Grow, or session count, license

• Platform, or flat, license

 

Cisco Unified Border Element licenses are available in both types on select platforms. Cisco Gatekeeper licenses are available in the platform license type only.

 

  • Pay-as-You-Grow License

 

This type of license covers the right to use the feature as well as the maximum session count allowed. An example is the FL-CUBE-25 license, which allows up to 25 sessions.

This license is designed to allow a specific number of sessions (or calls) on a platform. Purchase only as many sessions as are required in your deployment. You can add more licenses later as your needs expand, thus offering pay-as-you-grow benefits. Session licenses are stackable. These licenses are available on select platforms as given in Table 3, and are available on all software images. Examples include the FL-CUBE-4 and FL-CUBEE-100 licenses.

 

  • Platform License

 

This type of license covers the right to use the feature up to the maximum session count supported on the chosen platform. An example is the FL-INTVVSRV-2811 license, which allows the maximum number of sessions the Cisco 2811 platform supports.

These licenses are available on select platforms. These licenses require a software image.Examples include the FL-INTVVSRV-2801 and FL-GK-3945 licenses.

 

  • Cisco Unified Border Element Licenses

 

For Active/Standby redundant configurations, use the "Redundant-Platform" licenses. For all other configurations, including single-platform Active/Active load balancing, and Inbox redundant configurations, use the "Single-Platform" licenses.

 

Q: Can we Integrate CUBE with Siemens OSV. Can CUBE do it? What are the element in specific needed for Integration and deployment ? Please share a sample configurations?

 

A: We have validated the integration with Siemens HiPath 4000. More details on the integration is:

 

http://www.cisco.com/en/US/solutions/collateral/ns340/ns414/ns728/ns833/698642.pdf

 

 

Q22: I am trying to troubleshoot the Multicast MOH on Cube, how to do it?

 

Following commands will help you to analyse and troubleshoot the MOH issue you are facing on CUBE.

 

Debug commands:

  • debug ccm-manager music-on-old all
  • debug voip rtp
  • debug ccsip all

 

Show commands:

  • show version
  • show running configuration

When MMOH is being streamed, please collect the following output on CUBE:

 

  • show ccm-manager music-on-hold
  • show voip rtp connections
  • show call active voice compact

 

Note: Please collect the logs using buffered logging mechanism. You can configure the following:

no logging queue-limit

logging buffered 80000000

no logging rate-limit

no logging console

 

Q23: Debug commands on CUBE

 

DEBUG COMMANDS - Make sure to clear logg before call is made & get show logg after call is done

 

1. H.323 - H.323 Scenarios

debug h225 asn1

debug h225 events

debug h245 asn1

debug h245 events

debug h225 q931

debug cch323 all

debug voip ipipgw

debug voip ccapi inout

 

2. H.323 - SIP Scenarios

debug h225 asn1

debug h225 events

debug h245 asn1

debug h245 events

debug cch323 all

debug voip ipipgw

debug voip ccapi inout

debug ccsip all

 

3. SIP - SIP Scenarios

debug ccsip all

debug voip ccapi inout

 

4. Transcoder related scenarios

Apart from the debugs mentioned above based on the scenario

debug dspfarm all

debug sccp messages

 

 

Verifying Fundamental Cisco Unified Border Element Configurations

 

To verify Cisco Unified Border Element feature configuration and operation, perform the following steps (listed alphabetically) as appropriate.

 

 

Step 1 show call active video

 

Use this command to display the active video H.323 call legs.

 

Step 2 show call active voice

 

Use this command to display call information for voice calls that are in progress.

 

Step 3 show call active fax

 

Use this command to display the fax transmissions that are in progress.

 

Step 4 show call history video

 

Use this command to display the history of video H.323 call legs.

 

Step 5 show call history voice

 

Use this command to display the history of voice call legs.

 

Step 6 show call history fax

 

Use this command to display the call history table for fax transmissions that are in progress.

 

Step 7 show crm

 

Use this command to display the carrier ID list or IP circuit utilization.

 

Step 8 show dial-peer voice

 

Use this command to display information about voice dial peers.

 

Step 9 show running-config

 

Use this command to verify which H.323-to-H.323, H.323-to-SIP, or SIP-to-SIP connection types are supported.

 

Step 10 show voip rtp connections

 

Use this command to display active Real-Time Transport Protocol (RTP) connections.

 

 

This FAQ Document was created from the Cisco Unified Border Element related discussions in Cisco Support Community

 

Related Information

Comments
balaji.babu1
Level 1
Level 1

Hi Lavanya,

Cube and srst is not supported on the same 2911 gateway .

regards

balaji 

Jonathan Schulenberg
Hall of Fame
Hall of Fame

Please be aware that the answer to question 13 is incorrect.

Q13: Will SRST work on CUBE ?
A: Yes, SRST and CUBE can be co-located on the same router.

CUBE and SIP SRST aren't supported co-resident on any platform. CUBE and SRST - either SIP or SCCP - are not supported on ISR 4k. I have been told this first-person by both the PM and TME supporting CUBE as recently as June 2017. Some feature/call combinations will work but not all of them and since the developers weren't asked to explicitly build for and test that combination they can't be asked to support them after the fact. The product manager has to put that effort on the product development roadmap and commit hours/dollars to get it done.

The BU is well aware of this painful reality. Anything forward-looking is NDA-protected so I can't speak to the timeframe when/if this will be addressed here. You can reach out to your Cisco AM with any questions on that front.

eslam rizk
Level 4
Level 4

Good job bro , almost of CUBE info in simple document 
Thanks :))

Jonathan Schulenberg
Hall of Fame
Hall of Fame

To keep everyone updated, CUBE and SIP SRST are now supported co-resident on the same ISR 4000 series router beginning with IOS XE 16.7.1. The key feature that allowed this to happen is SIP multi-tenanancy, allowing the line- and trunk-side SIP feature sets to coexist without stepping on one another. Additional detail is provided in the CUBE Configuration Guide Supported Platforms chapter and SRST System Administrator Guide Configuring SIP Trunking on Unified SRST chapter.

 

In my opinion, we're unlikely to see SCCP co-residency added in the future. My impression is that Cisco has consolidated all future development effort on SIP, likely as a pragmatic realization that they can't keep up by keeping all of the "legacy" protocols afloat. Again, that's only my opinion.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: