This document covers the procedure on how to monitor the current call volume on gateway using Cisco Prime Collaboration.
About Cisco Prime Collaboration
Cisco Prime Collaboration provides a unified view of the entire IP communications infrastructure. It presents the current operational status of each element of the IP communications network. Cisco Prime Collaboration continuously monitors the current operational status of different IP communications elements, such as: CUCM, CUCME, Cisco Unity, Cisco Unified Contact Center, Cisco gateways, Cisco IP Phones etc.
There are queries from the customers asking, Is there a way to monitor the current call volume for the calls through the gateways configured with H.323 and SIP trunks using Cisco Prime Collaboration ?
Answer is Yes, you can monitor the current call volume on gateways. There's a "Calls Active" value available when you right click on the gateway and choose Performance. "This value represents the number of streaming connections that are currently active (in use); in other words, the number of calls that actually have a voice path connected."
Calls in setup mode or in teardown mode are not reported by this count.
View the performance report or graphs for Active Calls (Number) on a Cisco UBE by selecting the Performance right-click option from the UC Topology View.
The minimum and maximum of this value can also be collected over time for capacity planning purposes.
Real-time graphing of this parameter, compared with expected values based on historical data, is useful in detecting subtle system performance degradation (generally by detecting that the real-time number of calls active is below expected values compared to the same time-of-day/day-of-week baseline values).
For monitoring PRI channels, there is a "PRI Channels Active" value available.
This value represents the total number of B channels that are holding active voice calls. Collection of this data over time is used to understand call patterns and busy-hour peak calls. Baseline data can be used to detect real-time underutilization of circuits, an indication of possible system performance degradation (including otherwise hard-to-detect PSTN call routing or circuit-down conditions). Data trending allows for circuit growth and provisioning planning.
View the performance report or graphs for PRI channel utilization on a Cisco UBE by selecting the Performance right-click option from the UC Topology View.
To view related counters, go to Detailed Device View > IOS Gateway Port Usage.
More information on Managing Cisco UBE and Performance monitoring
Managing Cisco UBE
For Cisco Prime Collaboration to manage a Cisco Unified Voice Gateway, you must add the latter to Cisco Prime Collaboration using Operate > Device Work Center. When you want to add a Cisco UBE, keep the following information nearby: • The IP address or hostname • The SNMP read-only credentials
Once the Cisco UBE has been added and Cisco Prime Collaboration has collected the required inventory details from the device, Cisco Prime Collaboration marks the device as Managed. This signals that the Cisco UBE has been successfully added and is being managed by Cisco Prime Collaboration.
Cisco Prime Collaboration performs trending of the following categories on a Cisco UBE:
• Resource usage (DSP and its channels) • Call statistics (active calls) • Trunk statistics (trunk usage at DS0 level, port usage, gateway statistics) • MTP and Transcoder Sessions usage • Total, Inbound, Outbound Call Volume both at interface and dial-peer level You can view the performance report or graphs over the past 7 days by selecting the Performance right-click option on the device from the UC Topology View, and then selecting the performance parameter that you want to view. You can view multiple performance reports or graphs in a single screen
Hi, We need to upgrade our customer CUCM from 10.5 to 12.5. Can we upgrade from 10.5 to 12.5 directly.And will al licenses be migrated from 10.5 to 12.5 after upgrade or we need to purchase licenses. Thanks.
Hi Team, I have a customer who has Cisco Telepresence devices that are registered with CUCM, the Customer is looking to integrate Microsoft Teams with Telepresence Devices for Video Conference meetings. for this purpose, I offered him a CVI lice...
hi friends,in which version (subversion) of cucm, we can create one profile jabber for all devices ?? (pc,androis,ios,...) currently, i have cucm 11.5 su1,which i must create separate profile for each devices .. i want to know if it is possible ...
Hi all. I am hoping for some pointers or advice.I am having an issue where calls from CMS (v3.1.1) fail after 30 seconds when they call an older MOVI client (I appreciate that this is an older and no longer supported).Call path is CMS [neighbor] VCS-C [tr...
Bear with me - I'm trying to setup CUCM for a small multi-tenant scenario. Both tenants have shared resources (receptionists, assistants, conference rooms, etc). Fortunately these tenants are fairly trusted to each other, but for the sake of best pr...