NOTE: Even though we have g711ulaw configured under voice register pool for jabber client, in the INVITE message from Jabber client we always see g729 codec.
Config: ! voice register pool 1 registration-timer max 720 min 660 id mac 30F7.C583.E8D8 session-transport tcp type CiscoMobile-iOS number 1 dn 1 dtmf-relay sip-notify Codec g711ulaw username 6810 password cisco !
++++CME sends 488 Not Acceptable Media in response, since under voice register pool we had only g711 configured. SIP_UNACCEPTABLE_MEDIA_ERR Mar 2 08:30:29.458: //15204/37EECCC3BF4A/SIP/Error/sipSPIContinueNewMsgInvite: Unacceptable media indicated for INVITE
Sent: SIP/2.0 488 Not Acceptable Media Via: SIP/2.0/TCP 192.168.131.197:63438;branch=z9hG4bK3451ff19 From: "118216801" <sip:email@example.com>;tag=000000000000005800f06918-2783a723 To: <sip:firstname.lastname@example.org>;tag=46749EC-1C3A Date: Mon, 02 Mar 2015 08:30:29 GMT Call-ID: email@example.com CSeq: 101 INVITE Allow-Events: telephone-event Warning: 304 192.168.131.253 "Media Type(s) Unavailable" Reason: Q.850;cause=65 Server: Cisco-SIPGateway/IOS-12.x Content-Length: 0
++++After Disabling the Low bandwidth option on Jabber client. Config: ! voice register pool 1 registration-timer max 720 min 660 id mac 30F7.C583.E8D8 session-transport tcp type CiscoMobile-iOS number 1 dn 1 dtmf-relay sip-notify voice class codec 1 username 6810 password cisco ! voice class codec 1 codec preference 1 g711ulaw codec preference 2 g711alaw codec preference 3 g729r8 !
+++We can see now, Jabber client sending now all the configured codecs in the INVITE message to CME for outbound call.
NOTE: Make sure we do "create profile" under "voice register global" and restart the jabber application, every time a change is made under "voice register pool"
====Fix==== -Disable low bandwidth option on Jabber on iPhone IOS -We can keep low bandwidth option on jabber, but then g729 codec as to be there under voice register pool or voice-class codec applied on the voice register pool. So all the calls from/to Jabber client will be on g729 codec.
Phones on our voice vlan do not get a dhcp assigned ip address. However the computers connected to the switch do get an ip address on the access vlan. The switch has a trunk port going to the upstream switch and that looks fine. Any ideas?
Calls to some of our registered SX10/SX20 endpoints (usually from Zoom, but not always) end up with one-way video. The media paths shown in xstatus are address of the far-end system. There does not seem to be any obvious way to get our e...
Hello, We currently have SRST's at many remote sites. Each site has approximately 5-10 POTS lines which cost $20-$40/each depending on site. I was curious if it's possible to use something like cellular instead of POTS lines for this.&nbs...
We've just went from 10.5 to 11.5, and now, we're unable to maximize/stretch-to-fit dashboards. Previous versions allowed us to do so. This issue has been duplicated across multiple browsers. Any ideas?
Hi Team.CMS is working fine calls in and out from the box, what i need to do, is to assign some kind of ownership over the space/room, like webex, so the owner can mute and also dismiss the guest user from the space. Is it possible? Regards in advanc...