Starting from release TC5.1.0 a maintenance mode was added to the TelePresence software. This mode will kick in when a codec fails to boot or, in later releases, when a codec crashes. The user or engineer gets presented with a reduced set of commands to troubleshoot the system to determine whether the system is suffering a hardware or a software failure
Maintenance mode : access via telnet or ssh
When accessing the codec via the command line interface (telnet or ssh) as admin user, the user gets presented with a screen as shown below.
Server:/home/cisco # ssh firstname.lastname@example.org Welcome to the Cisco Telepresence maintenance shell.Type 'help' or '?' for help.
- User Commands -
help factoryreset pkgverify selectsw reboot version
The first thing that needs to be done is a capture of the logfiles. This can be done using the "log" command shown in the "User Commands" above. As soon as the command is executed, all logfiles from the codec are sent to the screen output, one after the other. It is paramount the ssh or telnet session is logging all screen output to a file which can then be attached to the service request.
User commands in maintenance mode
From this reduced shell one can reboot the codec.
reboot Really reboot? [yes/no] yes Rebooting.
Broadcast message from root@ex90-home (Mon Oct 8 13:20:37 2012): The system is going down for reboot NOW!
Other options are to execute a factoryreset, use selectsw to load a known working image, verify the version and pkgverify to do a sanity check of the current installed image. If the logfiles have been analyzed by the TAC and it has been determined the unit went into maintenance mode due to a software issue, we can fallback to the previous image, if one is present on the codec. Once the codec has been recovered, it can be upgraded to later release containing fix for the encountered bug.
Some versions have a rootsettings command too.
Welcome to the Cisco Telepresence maintenance shell. Type 'help' or '?' for help. help - User Commands - help factoryreset pkgverify selectsw reboot version rootsettings log OK rootsettings ? usage: rootsettings [on/serial/off/never/get] Command to control root user availability: get obtain current setting off root user is not available never root user permanently turned off serial [password] root user is available on serial port only on [password] root user is available on all ports. OK rootsettings on OK rootsettings on cisco
Having root access gives the additional option of putting all logfiles in a tar file and send them to a server.
Note : Once in maintenance mode you can download the logs to a SCP server. -OR- via PC by using windows SCP application. Maybe you need to open root via the 'rootsettings on' command. The logs which need to be attach to the service request .
Login to the system as root and tar the files :
tar -cvf /tmp/log.tar /var/log/* /var/log/eventlog/*
And then copy /tmp/log.tar.gz to a server. Or use your PC with winscp to get the file.
Printing of IP address of codec when in maintenance mode (TC5.1.5 or later)
An important enhancement to maintenance mode is the printing of the codec's IP address on the screen. Whether the address is obtained via DHCP or statically assigned : the user will now get notified which address to use to connect to the maintenance shell. The screen below was taken using TC5.1.5 release. However, the layout of this screen might change in TC6 release.
Maintenance mode : access via a web browser (TC6.0.1 or later)
Release TC6.0.1 added the possibility to use your web browser in order to connect to a codec running in maintenance mode. The user gets presented with the same user interface as when logged in as admin, however, some options are greyed out, i.e. they are not available. The user still has access to the diagnostics to retrieve the current and historical logfiles and he/she can upgrade the codec. Here again : first thing to do is retrieve both historical and current logfiles so they can be attached to the service request if/when you contact the TAC.
Hi expertsmay I ask how to force rtp go through cube, our voip environment isgenesys — cube — cucm All established call is point to point rtp transmition, cube is only forwarding signaling , is there any ways to make rtp can through cube?
I have an axis camera connected via third party sip to CUCM, when calling a newer sip phone whenever a DTMF is pressed the call disconnects. Works fine with older model phones, any ideas? if it helps I see this in wireshark before disconnect, BYE rea...
We have 2 servers running VMWare vSphere 6 Embedded Essentials, it was purchased as a part of our CUCM server from Cisco. We are looking to change the way we manage these 2 servers. Are we able to join these servers to our vCenter standard, and apply a st...
Hello, my apology for not posting a technical question. I'm a Avaya tech who wants to learn Cisco CUCM by building a mini CUCM home lab. I'm seeing a lot CME lab kits on Ebay however, I believe CUCM and CME are completely different from each o...