This document covers some of the best practices methodologies you should put into operation to secure and prevent Toll fraud on Cisco Unified Communications Manager Express and the IP Phones connected to the network.
How to secure Cisco Unified CME and IP Phones?
After-hours calling Restrictions
Call Transfer Restrictions
Call Forward Restrictions
Class of Restrictions (COR)
Securing GUI access on CME
Strict ephone Registration
Deny external traffic on Voice signaling ports
Disable ephone Auto-registration
Configuration examples are based on Cisco Unified CME Version 8.6.
1. After-hours Calling Restrictions
Cisco Unified CME enables you to configure toll restriction policies based on time and date. You can configure the calling policies so that the users are not allowed to make calls to predefined numbers during certain hours of the day and outside business hours.
CME1(config-telephony)# after-hours day Mon 20:00 08:00
CME1(config-telephony)# after-hours day Tue 20:00 08:00
CME1(config-telephony)# after-hours day Wed 20:00 08:00
CME1(config-telephony)# after-hours day Thu 20:00 08:00
CME1(config-telephony)# after-hours day Fri 20:00 08:00
CME1(config-telephony)# after-hours day Sat 12:00 12:00
CME1(config-telephony)# after-hours day Sun 12:00 12:00
Blocks calls outside of business hours, Monday to Friday before 8 am and after 8 pm.
This command disables the call transfer to any destination POTS or VOIP.
CME1(config)# ephone-template 2
CME1(config-ephone-template)# transfer max-length 4
This command specifies the maximum number of digits a user can dial when a call is transferred.
CME1(config)# ephone 10
CME1(config-ephone)# ephone-template 1
CME1(config)# ephone 20
CME1(config-ephone)# ephone-template 2
3. Call Forward Restrictions
For an attacker, the most convenient way to exploit a phone system for toll fraud is to have an insider do a call-forward to certain destinations. To restrict the number of digits that can be dialed by CME, you can use the call forward restriction feature.
CME1(config)# ephone-dn 60
CME1(config-ephone-dn)# number 5001
CME1(config-ephone-dn)# no forward local-calls
This feature restricts the call forward to local calls
This restricts the number of digits that can be dialed by CME during Call forward.
4. Class of Restrictions (COR)
Class of Restriction (COR) in CME is identical to voice gateways. You can apply the COR list in ephone-dn in addition to dial-peers.
CME1(config)# ephone-dn 10
CME1(config-ephone-dn)# number 1001
CME1(config-ephone-dn)# cor incoming internal
CME1(config-ephone-dn)# cor outgoing local
5. Securing GUI access on CME
SSL for HTTP (HTTPS) provides server authentication, encryption and message integrity to allow secure HTTP communications. SSL also provides HTTP client authentication. It is highly recommended to have Cisco Unified CME GUI interface secured with HTTPS access.
CME1(config)# ip http authentication AAA | TACACS | local
Default HTTPS port is 443, which can be changed to a higher port (none-1024) port number.
5. Strict ephone Registration
CME should be configured to enable only Cisco Unified IP Phones in the trusted domain (inside zone) for registration. You can use the strict-match option in ip source-address command so that only locally attached IP Phones can get register to CME.
CME1(config-telephony)# ip source-address 10.85.102.160 port <2000/5060> strict-match
In addition block TCP ports 2000-2002 and 5060 from the WAN to prevent external SCCP/SIP phone registration with CME.
6. Deny External Traffic on Voice signaling ports
CME1(config)# ip access-list extended BlockTraffic
CME1(config-ext-nac1) deny tcp any any range 2000 2002
CME1(config-ext-nac1) deny tcp any any eq 5060
CME1(config-ext-nac1) permit ip any any log
CME1(config)# interface FastEtherner 1/0
CME1(config-if)# ip access-group BlockTraffic in
7. Disable ephone Auto-Registration
CME enables auto-registration of ephones by default. This implies that new Cisco Unified IP Phones that try to register with CME are auto-registered with DN auto-assigned and are able to make calls immediately. You can disable auto-registration to prevent toll fraud.
CME1(config-telephony)# no auto-reg-ephone
Restricting SIP Phone Auto Registration : For SIP Phones you must configure the system so that the SIP endpoints must authenticate with a username and password
CME1(config)# voice register global
CME1(config-register-global)# mode cme
CME1(config-register-global)# source-address 10.85.102.152 port 5060
i have 8841 phone registered in the CUCM but i notice there is several phone that different in firmware.why is that ?how to resolve it ?Actual problem is that the phone with download status fail not able to call using VOIP function. Is that related ...
Hello,We are planning to have a SX20 on a Moving Cart. Is VLAN an absolute requirement for a VC device? This mobile system is more likely to be plugged in anywhere on multiple floors so we need to look at name based resolution not hardcoded IP’s
Hi All, For a particular directory number (egs : 8123) is mapped to specific mobile phone number in the translation pattern. When any desk phone from within the organization calls on the 8123 number it gets connected to the specific mobile phone and ...
We have an application where we want to integrate the following CMS page:https://join.xxxxxxxx.com/index.html?id=<id>secret=<secret>&lang=en-USThis works well, if we open a separate child window, but not embedded in an iframe:"Refused to d...