cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
75502
Views
18
Helpful
40
Comments
sagaskar
Level 1
Level 1

TITLE

Unable to share desktop on Jabber for Windows.

SYMPTOMS

The Desktop Sharing Option is grayed out in the Chat Window.

ENVIRONMENT

Cisco Jabber 9.0.1

Cisco Unified Communications Manager 8.6.1 and 8.6.2

Cisco Unified Presence Server 8.x (On-premises deployment)

Cisco WebEx Connect (Cloud based deployments)

CAUSES

To configure Cisco Unified Communications Manager for video desktop sharing, you need to apply a COP file to Cisco Unified Communications Manager and enable video desktop sharing on the SIP profiles of CSF devices.

RESOLUTION


Configuring Desktop Sharing on CUCM 8.6.1 - 

On the CUCM Admin page –

1. Enable desktop sharing on the SIP Profile for the appropriate CSF devices. To do that –
     - Select Device >Device Settings >SIP Profile
     - Select the appropriate SIP profile
     - In the Trunk Specific Configuration section, select Allow Presentation Sharing Using BFCP
     - Select Save

2. Apply the SIP profile to the appropriate CSF devices as follows:
     - Select Device > Phone on an individual device.
     - Use the Bulk Administration Tool for multiple devices.

Configuring Desktop Sharing on CUCM 8.6.2 -


On the CUCM –

1. Upload and apply the ‘cmterm-bfcp-e.8-6-2.cop.sgn ‘ COP file for desktop sharing, you can download the Admin folder on the following link to get access to the same.

http://www.cisco.com/cisco/software/release.html?mdfid=284324806&flowid=32202&softwareid=284006014&release=9.0%281%29&relind=AVAILABLE&rellifecycle=&reltype=latest

2. Restart the CUCM 8.6.2 as follows
     - Open the Cisco Unified OS Administration interface
     - Select Settings > Version
     - Select Restart
     - Repeat the steps for each node in the cluster, starting with the presentation server.

3. Enable video desktop sharing on the SIP Profile for the appropriate CSF devices and apply the SIP profile to the CSF devices, as outlined earlier.

4. Enable video desktop sharing capability on the appropriate devices as follows –
For an individual device, select Allow Presentation Sharing Using BFCP and then select Save
For multiple devices, do the following –
     - Select Bulk Administration > Phones > Export Phones > All Details.
     - Select Bulk Administration > Upload/Download Files and download the exported CSV file.
     - Open the CSV file with any editor.
     - Insert a column named Allow presentation sharing using BFCP into the CSV file.
     - Set the value of the column to Y for all required devices.
     - Save the CSV file.
     - Select the Override the existing configuration option.
     - Import the CSV file.
     - Select Run Immediately.
     - Select Submit.

PREVENTION

Note:  - As of this release, Cisco Jabber for  Windows supports video desktop sharing in software phone mode only.  Video desktop sharing is not available in desk phone mode.

- You cannot enable video desktop sharing on the default SIP profile.  You can copy the default SIP Profile and save it as a new one.

RELATED TOPICS

http://www.cisco.com/en/US/docs/voice_ip_comm/jabber/Windows/9_0_1/b_jabber_win_icg_chapter_010.html#task_002CD757B8EC4F5E85AA5222626C772B

Comments
AskQ2Forum_2
Level 1
Level 1

Hi i only see the jabber msi in the jabber admin file , I dont see a ccm folder with cop files in. Please advise, obviously doing something wrong here.

gonzalezel
Level 1
Level 1

So this COP file needs to be installed on all the callmanager servers in the cluster and then rebooted.  Is that correct?  Does this file need to be installed on the Presence (CUP) server?

fvazquez
Level 1
Level 1

Yes, that's correct. You need to do it first on the CUCM publisher, reboot server, be shure there's no problem with installation and after that you need to do it on the CUCM subscriber(s). Just need to install file on the CUCM cluster, not on CUP.

jameskeagie
Level 1
Level 1

I am just curious - will this eventually extend to other SIP devices as well (i.e. 8900 and 9900 series video phones?)

It would be great to share your desktop to a deskphone or enduser to assist with a helpdesk ticket (i.e. - look here, click on the button that looks like this etc.) especially if there was a preference to allow selection of a bounding box area of your screen, or follow the mouse on your screen for the video feed.

tpejnovi
Cisco Employee
Cisco Employee

Sana,

Small correction on procedure described in this document. When updating CSV file to allow desktop sharing, value should be changed to T and not Y:

- Set the value of the column to Y for all required devices.  <<<--------- Wrong,  it should be T

Regards,

Tijana

Javastudy
Level 1
Level 1

I would like correct above doc under " Configuring Desktop Sharing on CUCM 8.6.2 "

Enable video desktop sharing capability on the appropriate devices as follows –

For an individual device, select Allow Presentation Sharing Using BFCP and then select Save

For multiple devices, do the following –

- Select Bulk Administration > Phones > Export Phones > All Details.

- Select Bulk Administration > Upload/Download Files and download the exported CSV file.

- Open the CSV file with any editor.

- Insert a column named Allow presentation sharing using BFCP into the CSV file.

- Set the value of the column to Y for all required devices.  <<<-----the value should be "T " not " Y"

- Save the CSV file.

- Select the Override the existing configuration option.

- Import the CSV file.

German Zamora
Level 1
Level 1

Updating the post for 9.X versions of CM. As per the below statement and document, in CM 9.X and greater, the COP file is not longer needed, since BFCP presentation is enabled by default.

Cisco Jabber for Windows 9.2.x Server Setup Guide - Set Up On-Premises Deployments with Cisco Unified Communications Manager Version 9.x and Higher

On Cisco Unified                       Communications Manager version 9.0(1) and higher, BFCP presentation sharing is automatically enabled

http://tools.cisco.com/squish/cd95C

4rmorris
Level 1
Level 1

This post (and all the Cisco docs I could find) neglect to mention that any firewall or IPS software running on the PC (like Symantec or Mcafee) needs to be configured to allow UDP port 5070 in and out of the PC.  I followed all the instructions, but I ended up doing a Wireshark capture with the firewall off to confirm exactly what was happening (UDP 5070 to negotiate BFCP, then h.264 in RTP packets).

So don't forget to update your host-based firewall to permit UDP port 5070 in and out for BFCP.

Ryan

RachelGomez161999
Spotlight
Spotlight

Try this steps-

- Select Device >Device Settings >SIP Profile.
- In the Trunk Specific Configuration section, select Allow Presentation Sharing Using BFCP.
- Select Save.
- Select Device > Phone on an individual device.
- Open the Cisco Unified OS Administration interface.
- Select Settings > Version.
- Select Restart.

-Try again

 

Greeting,

Rachel Gomez

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: