12-20-2011 06:30 AM - edited 03-14-2019 09:04 AM
Hello everyone!
I have a strange problem regarding Cisco Unified CCX Database service.
Situation is the following:
UCCX 8.5.1 in HA Cluster
And from time to time, on 1st UCCX Cisco Unified CCX Database is going OUT OF SERVICE.
In CLI utils service list shows that service is STARTED, but in Web-Interface is OUT OF SERVICE.
Whether I restart it through CLI or Web, it stays in INITIALIZING status in Web, but in CLI is STARTED!!
After restart of the system everything goes back like it should be.
Don't see anything unusual in logs.
Any similar experiences? .... Any help or hint is appreciated!!
Thank you
A
01-23-2012 08:11 PM
I'm experiencing the same issue. Any ideas guys?
01-23-2012 08:28 PM
Guys,
Please post the exact UCCX version here, as it is displayed on UCCX App admin page.
If I understood correct, there is no impact on functionality but the visuals are confusing, right ?
Is it HAoWAN or LAN ? Such behavior is seen on UCCX Pub or Sub ?
GP.
01-23-2012 11:34 PM
Hi
I've seen this several times on 8.5... a reboot of the affected node brings it back until it decides to fail again. A bug for sure, but I've not had the chance to open a TAC case for it yet...
Principal Engineer at Logicalis UK
Please rate helpful posts...
11-02-2012 01:40 AM
Hi Aaron,
You are probably running into the defect CSCts80098.
That is why rebooting the server will bring the database back into service. A restart of CVD will also do.
Please rate helpful posts.
-thanks
Mohana
01-24-2012 11:50 AM
Hi Alex,
This is a known issue due to the migration from a MCS server to a UCs Server
Defect ID :CSCtl05454
The reason this is happening is due to
Migrating from MCS to UCS but not keeping all settings intact like changing the case of the hostname
-Please upgrade to SU1 or SU2 to have this resolved
Thanks,
Prashanth
10-31-2012 04:44 AM
We have this same issue, no new applications can be configured though. We're going to restart the server out of hours so hopefully that brings it back to normal. As indicated above, through the CLI the database shows as 'Started', however on the ccx serviceability it shows as out of service.
11-02-2012 01:39 AM
Hi,
Are you on a pre SU2 release? You are probably running into the defect CSCts80098.
This is why a reboot of the server will bring it back into service. A restart of CVD will also do.
Please rate helpful posts.
-thanks
Mohana
11-02-2012 01:57 AM
We're on 8.5.1.1000-37. We'll be looking to upgrade soon and have been on this version for almost a year without issues, so not a bad run.
11-02-2012 02:27 AM
Hi Ashley,
That is probably the bug you are hitting then. You can move to SU2 or SU3 and you wont face any problems.
Please rate helpful posts.
-thanks
Mohana
01-21-2013 01:16 AM
Hi Ashley/Mohana,
We are also experiencing the similar issue as you were. So what exactly you guys did to make it working.
Did restarting process went successfully and you didnt face any issues. I would appreciate if you can share your part.
Coz I am experiencing the very same ; no new applications can be configured though. Through the CLI the database shows as 'Started', however on the ccx serviceability it shows as out of service.
01-21-2013 01:32 AM
Hi Muhammad,
The restart resolved my issue. I performed a cluster reboot for UCCX (Primary/Secondary) and we were then able to add applications. We haven't had any issues since, so without going through logs i couldn't tell you what the cause was.
Ashley
01-21-2013 01:41 AM
Thanks Ashley for your prompt response! We're thinking of the same but might involve TAC to look into the core.
01-21-2013 02:01 AM
Hi all
As pointed out above by Mohana (+5) the bug is CSCts80098.
You can reboot, restart CVD, or apply the latest SU for your release to resolve it fully.
Aaron
08-28-2013 06:28 AM
In the database control center, Disable CDS and HDS and then Enable CDS and HDS will work without rebooted both servers.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide